6061铝合金厚层搅拌摩擦增材工具凸台的影响

doi:10.3969/j.issn.1004-132X.2026.10.010

摘要/Abstract

摘要：

为提高搅拌摩擦增材制造效率，开发了一种高沉积层厚工艺，探究了工具凸台对沉积层内材料流动、组织演变与力学性能的影响。研究结果表明，沉积层稳定温度和均匀表面确保了高质量成形；工具凸台导致沉积层内形成凸台作用区与非作用区，凸台作用区材料呈碗口状涡旋流动，非作用区表现为稳定层流；沉积层晶粒相比原料均显著细化，凸台作用区因高应变率与短时高温，抑制晶粒再结晶过程，而非作用区在适中条件下实现了充分的动态再结晶；在性能方面，与原料棒相比，非凸台作用区抗拉强度下降了约40.8%，但断后伸长率显著提高了约115%，而凸台作用区旋转挤压的成形模式诱发高位错密度与晶格畸变导致拉伸中过早断裂，抗拉强度与断后伸长率仅为141.1 MPa与5.7%。

关键词: 搅拌摩擦沉积增材, 高层厚, 工具凸台, 组织演变, 力学性能

Abstract:

To improve the efficiency of additive friction stir deposition， a thick-layer process was developed to investigate the effect of tool protrusions on the material flow， microstructure evolution， and mechanical properties of the deposited layer. The results show that the stabilized temperature and uniform surface of the deposited layer ensure high quality forming. The tool protrusions lead to the formation of a tool protrusion-effective zone （TPEZ） and a tool protrusion non-effective zone （TPNZ） within the deposition， materials in the TPEZ exhibit a vortex-like flow with a bowl-shaped profile， while those in the TPNZ show stable laminar flow. The grains in the deposited layer are significantly refined compared with the raw material， and the high strain rate and short-term high temperature in the TPEZ inhibit the grain recrystallization process， while the TPNZ achieve sufficient dynamic recrystallization under moderate conditions. In terms of mechanical properties， the TPNZ showed a 40.8% decrease in tensile strength but a 115% increase in elongation after fracture compared with the feedstock rod. In contrast， the TPEZ exhibited premature fracture due to high dislocation density and lattice distortion induced by rotational-extrusion-dominated deformation， with a tensile strength and elongation of only 141.1 MPa and 5.7%， respectively.

Key words: additive friction stir deposition, thick-layer, tool protrusion, microstructure evolution, mechanical properties

中图分类号:

TP453

王帅普, 赵磊, 王云龙, 陈琦, 王俊红, 吴志林. 6061铝合金厚层搅拌摩擦增材工具凸台的影响[J]. 中国机械工程, 2026, 37(10): 2476-2483.

WANG Shuaipu, ZHAO Lei, WANG Yunlong, CHEN Qi, WANG Junhong, WU Zhilin. Effect of Tool Protrusion in Thick-layer Additive Friction Stir Deposition of 6061Aluminum Alloy[J]. China Mechanical Engineering, 2026, 37(10): 2476-2483.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2026.10.010

https://www.cmemo.org.cn/CN/Y2026/V37/I10/2476

图/表 16

表1 6061-T6铝合金成分 (%)

Tab.1 Composition of the 6061-T6 aluminum alloy

成分	Si	Fe	Cu	Mn	Mg	Cr	Zn	Ti	Al
质量分数	0.55	0.35	0.35	0.05	1.0	0.25	0.15	0.10	其余

图1 6061-T6原料棒微观组织

Fig.1 Microstructure of the 6061-T6 feedstock

表2 6061-T6铝合金力学性能

Tab.2 Mechanical properties of 6061-T6 aluminum alloy

屈服强度	抗拉强度	断后伸长率	硬度
275 MPa	346 MPa	13.9%	113HV

图2 AFSD 工艺示意图

Fig.2 Schematic of the AFSD process

图3 AFSD设备及沉积层宏观形貌

Fig.3 AFSD setup and macroscopic view of the deposit

图4 沉积层样品分割示意图

Fig.4 Schematic of the sample sectioning for the deposited layer

图5 AFSD沉积层温度演变

Fig.5 Temperature evolution of the deposited during AFSD

图6 AFSD稳定沉积3D形貌

Fig.6 3D morphology of the AFSD deposit

图7 沉积层内材料流动观察

Fig.7 Observation of material flow within the deposited layer

图8 沉积层晶粒反极图、尺寸分布及取向差角统计

Fig.8 Inverse pole figure， grain size distribution， and misorientation angle statistics of grains in the deposited layer

图9 TPEZ和TPNZ核平均取向差与几何必须位错密度

Fig.9 KAM and GND density in the TPEZ and TPNZ

图10 TPEZ和TPNZ晶粒类型分布及占比统计

Fig.10 Distribution and proportion statistics of grain types in the TPEZ and TPNZ

图11 层内不同区域晶粒演变过程机制

Fig.11 Schematic of the grain evolution mechanism in different intra-layer regions

图12 沉积层层内不同区域维氏硬度分布

Fig.12 Distribution of Vickers hardness in different regions of the deposited layer

图13 原料棒及沉积层不同区域拉伸性能统计

Fig.13 Tensile properties of the feedstock and different regions of the deposited layer

图14 不同区域拉伸断口形貌观察

Fig.14 Morphology observation of tensile fracture from different regions

参考文献 26

[1]	卢秉恒，李涤尘. 增材制造（3D打印）技术发展［J］. 机械制造与自动化， 2013， 42（4）： 1-4.
	LU Bingheng， LI Dichen. Development of the Additive Manufacturing （3D Printing）Technology［J］. Machine Building & Automation， 2013， 42（4）： 1-4.
[2]	DEBROY T， WEI H L， ZUBACK J S， et al. Additive Manufacturing of Metallic Components-process， Structure and Properties［J］. Progress in Materials Science， 2018， 92： 112-224.
[3]	李权，王福德，王国庆，等. 航空航天轻质金属材料电弧熔丝增材制造技术［J］. 航空制造技术， 2018， 61（3）： 74-82.
	LI Quan， WANG Fude， WANG Guoqing， et al. Wire and Arc Additive Manufacturing of Lightweight Metal Components in Aeronautics and Astronautics［J］. Aeronautical Manufacturing Technology， 2018， 61（3）： 74-82.
[4]	ZHANG H， DONG Y， LI N， et al. Microstructure and Mechanical Properties of 6061 Aluminum Alloy/Galvanized Steel Laser-arc Hybrid Fusion-brazed Welded Joint： Experiment and First-principles Calculation［J］. China Welding， 2025， 34（3）： 192-206.
[5]	YI H， YANG L， JIA L， et al. Porosity in Wire-arc Directed Energy Deposition of Aluminum Alloys： Formation Mechanisms， Influencing Factors and Inhibition Strategies［J］. Additive Manufacturing， 2024， 84： 104108.
[6]	CHU Y， ZHAO X， SUN W， et al. Laser Directed Energy Deposition Additive Manufacturing Using Friction Stir Channelling Extruded Wire［J］. Journal of Manufacturing Processes， 2025， 154： 122-133.
[7]	YAP C Y， CHUA C K， DONG Z L， et al. Review of Selective Laser Melting： Materials and Applications［J］. Applied Physics Reviews， 2015， 2（4）： 041101.
[8]	ABDOLLAHZADEH A， BAGHERI B， ABBASI M， et al. A Modified Version of Friction Stir Welding Process of Aluminum Alloys： Analyzing the Thermal Treatment and Wear Behavior［J］. Proceedings of the Institution of Mechanical Engineers， Part L： Journal of Materials： Design and Applications， 2021， 235（10）： 2291-2309.
[9]	LI X， LI X， HU S， et al. Additive Friction Stir Deposition： a Review on Processes， Parameters， Characteristics， and Applications［J］. The International Journal of Advanced Manufacturing Technology， 2024， 133（3）： 1111-1128.
[10]	YU H Z， JONES M E， BRADY G W， et al. Non-beam-based Metal Additive Manufacturing Enabled by Additive Friction Stir Deposition［J］. Scripta Materialia， 2018， 153： 122-130.
[11]	赵磊，王帅普，武明建，等. 6061铝合金非连续搅拌摩擦增材制造与性能研究［J］. 精密成形工程， 2024， 16（12）： 124-132.
	ZHAO Lei， WANG Shuaipu， WU Mingjian， et al. Synthesis and Performance of 6061 Aluminum Alloy via Non-continuous Friction Stir Additive Manufacturing［J］. Journal of Netshape Forming Engineering， 2024， 16（12）： 124-132.
[12]	石磊，李阳，肖亦辰，等. 基于搅拌摩擦的金属固相增材制造研究进展［J］. 材料工程， 2022， 50（1）： 1-14.
	SHI Lei， LI Yang， XIAO Yichen， et al. Research Progress of Metal Solid Phase Additive Manufacturing Based on Friction Stir［J］. Journal of Materials Engineering， 2022， 50（1）： 1-14.
[13]	PHILLIPS B J， AVERY D Z， LIU T， et al. Microstructure-deformation Relationship of Additive Friction Stir-deposition Al-Mg-Si［J］. Materialia， 2019， 7： 100387.
[14]	BECK S C， RUTHERFORD B A， AVERY D Z， et al. The Effect of Solutionizing and Artificial Aging on the Microstructure and Mechanical Properties in Solid-state Additive Manufacturing of Precipitation Hardened Al-Mg-Si Alloy［J］. Materials Science and Engineering： A， 2021， 819： 141351.
[15]	ZENG C， GHADIMI H， DING H， et al. Microstructure Evolution of Al6061 Alloy Made by Additive Friction Stir Deposition［J］. Materials， 2022， 15（10）： 3676.
[16]	PARIYAR A， YASA E， SHARMAN A， et al. Understanding Process Parameter-induced Variability for Tailoring Precipitation Behavior， Grain Structure， and Mechanical Properties of Al-Mg-Si-Mn Alloy during Solid-state Additive Manufacturing［J］. Materials & Design， 2024， 245： 113238.
[17]	TANG W， YANG X， TIAN C. Influence of Rotation Speed on Interfacial Bonding Mechanism and Mechanical Performance of Aluminum 6061 Fabricated by Multilayer Friction-based Additive Manufacturing［J］. The International Journal of Advanced Manufacturing Technology， 2023， 126（9）： 4119-4133.
[18]	CHEN G， WU K， WANG Y， et al. Effect of Rotational Speed and Feed Rate on Microstructure and Mechanical Properties of 6061 Aluminum Alloy Manufactured by Additive Friction Stir Deposition［J］. The International Journal of Advanced Manufacturing Technology， 2023， 127（3）： 1165-1176.
[19]	QIAO Q， ZHOU M， GONG X， et al. In-situ Monitoring of Additive Friction Stir Deposition of AA6061： Effect of Layer Thickness on the Microstructure and Mechanical Properties［J］. Additive Manufacturing， 2024， 84： 104141.
[20]	CHEN G， WU K， WANG Y， et al. Quantitative Study on the Correlation between Microstructure and Mechanical Properties of Additive Friction Stir Deposited 6061-T6 Al-Mg-Si Alloy［J］. Journal of Materials Research and Technology， 2023， 25： 6725-6736.
[21]	TANG W， YANG X， LUO T， et al. Precipitation Behavior and Strengthening-toughening Mechanism of Additive Friction Stir-deposited Al-Mg-Si-Cu Alloy［J］. Additive Manufacturing， 2023， 76： 103785.
[22]	CHEN L， JIANG T， LI J， et al. Microstructure and Mechanical Properties of 2195 Al-li Alloy via Friction Stir Additive Manufacturing with Different Stirring Paths［J］. Journal of Alloys and Compounds， 2024， 1008： 176666.
[23]	LI Y， HE C， WEI J， et al. Correlation of Local Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloy Build Fabricated via Underwater Friction Stir Additive Manufacturing［J］. Materials Science and Engineering： A， 2021， 805： 140590.
[24]	MA K， WEN H， HU T， et al. Mechanical Behavior and Strengthening Mechanisms in Ultrafine Grain Precipitation-strengthened Aluminum Alloy［J］. Acta Materialia， 2014， 62： 141-155.
[25]	HANSEN N， HUANG X. Microstructure and Flow Stress of Polycrystals and Single Crystals［J］. Acta Materialia， 1998， 46（5）： 1827-1836.
[26]	LEI Z， HE L， LIU R， et al. Pore-induced Crack Initiation Mechanism and Life Prediction in Additively Manufactured High-strength Aluminum Alloy during High Cycle Fatigue［J］. Engineering Failure Analysis， 2026， 184： 110285.