Lubrication Analysis of Vane-stator Pair in a Variable Vane Pump Based on Different Apical Radius of Vane

Abstract

Abstract:

Aiming at the direct contact between vane and stator in pre-lower pressure area which will aggravate the wear conditions, lubricating state and elastohydrodynamic lubrication model of vane-stator pair in vane pump were discussed.Then pressure distribution in contact area was studied by numerical simulation.Through analysing the effects of apical radius and bearing area of vane on mechanics property,the influences of them on the hydrodynamic lubrication performance of vane-stator pair were investigated.Results show that poor lubrication performance occure near the end of pre unloading zone. The effects of the change of bearing area on mechanics and lubrication performance can not be ignored. Increase of the apical radius can improve the lubrication condition and lead the distribute of pressure more uniformity. Therefore the lubricating condition is more stable and reliable.

Key words: variable vane pump, vane-stator pair, apical radius, lubrication characteristics, numerical simulation

摘要：

针对叶片泵叶片-定子副在预卸压区中易发生对偶面间直接接触而加剧磨损的状况,通过分析叶片-定子副在预卸压区中的润滑状态,建立了叶片-定子副的弹流动压润滑模型，并数值模拟了接触区内压力分布，结合叶顶曲率半径和叶顶承载面积的变化对叶片-定子副间力学特性的影响，分析了叶顶曲率半径和叶顶承载面积的变化对动压油膜润滑性能的影响。结果表明：叶片-定子副处于预卸压区末端时润滑状况最差；承载面积的变化对叶顶载荷和润滑性能的影响不容忽视；增大叶顶半径后能改善摩擦副的润滑状态，许可范围内随叶顶曲率半径增大，接触区内油膜压力分布更趋均匀，叶片-定子副间的润滑状况也更加稳定可靠。

关键词: 变量叶片泵, 叶片定子副, 叶顶曲率半径, 润滑特性, 数值分析

CLC Number:

TH324

Zhang Guotao, Yin Yanguo. Lubrication Analysis of Vane-stator Pair in a Variable Vane Pump Based on Different Apical Radius of Vane[J]. China Mechanical Engineering, 2015, 26(18): 2481-2485,2490.

张国涛, 尹延国. 基于叶顶曲率半径变化的变量叶片泵叶片-定子副润滑数值分析[J]. 中国机械工程, 2015, 26(18): 2481-2485,2490.

References

[1]檀润华,苑彩云.弹流理论在单作用叶片泵叶片顶廓设计中的应用[J].河北工学院学报,1991,20(3):43-50.
Tan Runhua,Yuan Caiyun.The Application of Elastic Fluid Theory to the Design of Vane Outline of Variable Displacement Vane Pump[J].Journal of Hebei Institute of Technology,1991,20(3):43-50.
[2]张国涛,尹延国.变量叶片泵闭死容腔中压力变化特性及叶片受力分析[J].应用数学和力学,2014,35(4):401-411.
Zhang Guotao,Yin Yanguo.Pressure Variation in Sealed Cavity and Force Analysis on Vanes in Variable Displacement Vane Pumps[J].Applied Mathematics and Mechanics,2014,35(4):401-411.
[3]王德石,赖声远.流体动压支承高速叶片泵的设计方法[J].大连铁道学院学报,1994,15(2):69-72.
Wang Deshi,Lai Shengyuan.The Designing Method of the High-speed Rotation Vane Pump Supported by the Fluid Dynamic Pressure[J]. Journal of Dalian Railway Institute,1994,15(2):69-72.
[4]Kim H J.Lubrication Oil Pumping by Utilizing Vane Motion in a Horizontal Rotary Compressor[J].International Journal of Refrigeration,2005,28(4):498-505.
[5]Jeon H G,Oh S D,Lee Y Z.Friction and Wear of the Lubricated Vane and Roller Materials in a Carbon Dioxide Refrigerant[J]. Wear,2009,267(5):1252-1256.
[6]Cho M R,Han D C.Vane Tip Detachment in a Positive Displacement Vane Pump[J].Journal of Mechanical Science and Technology,1998,12(5):881-887.
[7]Jang J S, Kim K H,Cho M R, et al. The Characteristics of Pressure Ripple in Variable Displacement Vane   Pumps: Comparison between Theory and Experiment[J].Proceedings of the Institution of Mechanical Engineers.Part A:Power and Energy,2002,216(1):89-96.
[8]Gellrich R, Kunz A, Beckmann,et al. Theoretical and Practical Aspects of the   Wear of Vane Pumps Part A. Adaptation of a Model for Predictive Wear Calculation[J].Wear,1995,181/183(2):862-867.
[9]Kunz A,Broszeit E,Gellrich R,et al. Theoretical and Practical Aspects of the Wear of Vane Pumps Part B.Analysis of a Wear Behaviour in   the Vickers Vane Pump Test[J].Wear,1995,181/183(2):868-875.
[10]Cho I,Oh S H,Jung J Y.The Lubrication Characteristics of the Vane Tip under Inlet Pressure Boundary Conditions for an Oil Hydraulic Vane Pump[J].Journal of Mechanical Science and Technology,2005,19(12):2179-2186.
[11]Cho I,Oh S H,Song K K,et al.The Lubrication Characteristics of the Vane Tip Under Pressure Boundary Condition of Oil Hydraulic Vane Pump[J].Journal of Mechanical Science and Technology,2006,20(10):1716-1721.
[12]Mucchi E,Cremonini G,Delvecchio S,et al.On the Pressure Ripple Measurement in Variable Displacement Vane Pumps[J]. Journal of Fluid Engineering,2013,135(9):91-103.
[13]Mucchi E,Agazzi A,Delia G,et al.On the Wear and Lubrication Regime in Variable Displacement Vane Pumps[J]. Wear, 2013,306(1/2):36-46.
[14]温诗铸,杨沛然.弹性流体动力润滑[M].北京:清华大学出版社,1998.

[1]	TUN Fu-Chao, TUN Bai-Hu, ZHANG Xiu-Hua. Numerical Simulation of Heat Transfer Performance of Paraffin Thermal-Sensitive Valve  [J]. J4, 201016, 21(16): 1921-1926.
[2]	GUO Wei, SUN Hongming, XU Gaofei, LI Guangwei, ZHOU Yue, WANG Minjian, . Improvements for Landing Impact Characteristics and Concentrated Stress Structures of Full Ocean Depth Landing Vehicles [J]. China Mechanical Engineering, 2021, 32(07): 867-874.
[3]	DU Fei;WANG Xinyun;DENG Lei;XIA Juchen;JIN Junsong. Research Progresses of HVIW Technology [J]. China Mechanical Engineering, 2021, 32(05): 600-610.
[4]	QIAO Wei1;YAO Weixing1,2. Numerical Analysis of Shear-lag Effect on Curing Deformation of Composites [J]. China Mechanical Engineering, 2021, 32(05): 611-616,623.
[5]	HU Jian1;CHEN Zezhong1;LIU Tao2;YANG Jinhua3. Simulation and Tests on Hot Forming Process Optimization for Door Anti-collision Beams [J]. China Mechanical Engineering, 2021, 32(01): 92-100.
[6]	HUA Shaozhen, MENG Fanjing, LIU Huabo, DING Hai. Study on Three Dimensional Simulation and Elimination Countermeasures of Melt Jetting Phenomenon in Injection Molding [J]. China Mechanical Engineering, 2020, 31(22): 2715-2722.
[7]	HU Mian;DING Xiaohong. Numerical and Experimental Investigations of Thermal Performance for Heat Pipe Ball Screws [J]. China Mechanical Engineering, 2020, 31(20): 2445-2453.
[8]	WANG Lin1;PAN Jun1;HE Qingchuan1;DING Wei2;GU Liwei2. Welding Process Optimization on Robot Welding of the Backward Centrifugal Fan Impeller [J]. China Mechanical Engineering, 2020, 31(19): 2379-2387.
[9]	WANG Guan1；ZHANG Qian2；KOU Linyuan1；LIU Zhiwen3；LI Shikang3. Nonlinear Topology Optimization of Continuum Structures Based on HCA Algorithm [J]. China Mechanical Engineering, 2020, 31(18): 2161-2173.
[10]	BAO Daorina；LIU Xujiang；WANG Xiaoxue；WANG Shuailong；LIU Jiawen. Analysis of Output Characteristics for Small Horizontal Axis Variable Eccentricity Wind Turbines [J]. China Mechanical Engineering, 2020, 31(18): 2196-2205.
[11]	TONG Zheming1；CHEN Yao1；TONG Shuiguang1；YU Yue1；LI Jinfu2；HAO Guoshuai3. Multi-objective Optimization Design of Low Specific Speed Centrifugal Pumps Based on NSGA-Ⅲ Algorithm [J]. China Mechanical Engineering, 2020, 31(18): 2239-2246.
[12]	SHEN Jianbang;XIAO Junhua;LIANG Xi;XU Yaoling. Numerical Study on In-plane Impact Dynamics of Negative Poisson's Ratio Honeycomb Structures with Curved Concave Sides [J]. China Mechanical Engineering, 2020, 31(16): 1998-2004.
[13]	SONG Shouxu1,2;HU Mengcheng1,2;DU Yi1,2;LUO Rundong1,2. Strain Numerical Simulation and Torque Imbalance Analysis of Remanufactured Motors with Mixed Stator Core [J]. China Mechanical Engineering, 2020, 31(09): 1080-1088.
[14]	ZOU Weisheng1 ;LIU Ruixian1;LIU Shaojun2. Study on Lifting Motor Pumps for Coarse Particle Slurry in Sea Bed Mining [J]. China Mechanical Engineering, 2019, 30(24): 2939-2944.
[15]	YUE Minnan1;LI Chun1,2;HAO Wenxing1;ZHANG Junwei1. Effects of Flap on Aerodynamic and Noise Characteristics of Airfoils [J]. China Mechanical Engineering, 2019, 30(12): 1409-1416.