Numerical Simulation of Abrasive Flow Machining in Multi-angle Elbows

doi:10.3969/j.issn.1004-132X.2021.11.005

Abstract

Abstract: Abrasive particle flow processing technology was applied to complete the numerical simulation of inner surface polishing processes of multi-angle elbows. Effects of inlet flow velocity and abrasive concentration on abrasive particle flow polishing processes were studied by FLUENT software under different bending angles. Effect laws of inlet flow velocity and abrasive concentration on local pressure differences of bent pipe, inlet and outlet pressure differences, and turbulence intensity were obtained. The overall effects of the pressure and velocity were analyzed. Then the suitable working conditions of the inner surfaces of abrasive particle flow polishing pipes were obtained. Based on this, an unsteady numerical simulation of heat accumulation was carried out during abrasive flow polishing processes. Simulation results show that the temperature changes are small during the processes. These results provide a reference for actual abrasive flow processes.

Key words: numerical simulation, abrasive particle flow, multi-angle elbow, flow heat generation

摘要： 采用磨粒流加工工艺对多角度弯曲管内表面抛光过程进行数值模拟研究。利用FLUENT软件研究了不同弯曲角度下入口流速、磨料浓度对磨粒流抛光工艺过程的影响，得到了入口流速、磨料浓度对弯管局部压差、进出口压差、湍流强度等参数的影响规律。对压力和速度的整体作用效果进行了分析，得出了磨粒流抛光细长管类零件内表面的适宜工况。在此基础上，进行了磨粒流抛光过程热量积聚的非稳态模拟，模拟结果表明加工过程中温度变化较小。研究结果为实际磨粒流加工提供了参考。

关键词: 数值模拟, 磨粒流, 多角度弯曲管, 流动产热

CLC Number:

TH164

YIN Hongchao, LIU Xiao, ZHAI Zhende, MU Lin. Numerical Simulation of Abrasive Flow Machining in Multi-angle Elbows[J]. China Mechanical Engineering, 2021, 32(11): 1299-1306.

尹洪超, 刘宵, 翟镇德, 穆林. 多角度弯曲管磨粒流加工数值模拟研究[J]. 中国机械工程, 2021, 32(11): 1299-1306.

References

［1］耿健. 气压砂轮抛光工具的有限元建模及动力学分析［D］.杭州：浙江工业大学,2016.
GENG Jian. Finite Element Modeling and Dynamic Analysis of Pneumatic Grinding Wheel Polishing Tool［D］.Hangzhou：Zhejiang University of Technology, 2016.
［2］何雅玲, 汤松臻, 王飞龙, 等. 中低温烟气换热器气侧积灰、磨损及腐蚀的研究［J］.科学通报,2016,61(17):1858-1876.
HE Yaling, TANG Songzhen, WANG Feilong. et al. Study on Ash, Abrasion and Corrosion on the Gas Side of Medium and Low Temperature Flue Gas Heat Exchanger［J］. Chinese Science Bulletin,2016,61(17):1858-1876.
［3］王坤,胡杰珍,王贵,等.管流式冲蚀装置异径管固液两相流场数值分析［J］.真空科学与技术学报,2019,39(9):831-837.
WANG Kun, HU Jiezhen, WANG Gui, et al. Numerical Analysis of Solid-Liquid Two-phase Flow Field in Different-diameter Pipes of Tube-flow Erosion Device［J］. Journal of Vacuum Science and Technology, 2019,39(9):831-837.
［4］李昳. 离心泵内部固液两相流动数值模拟与磨损特性研究［D］. 杭州：浙江理工大学,2014.
LI Yi. Numerical Simulation of Solid-Liquid Two-phase Flow and Wear Characteristics in a Centrifugal Pump［D］. Hangzhou：Zhejiang University of Technology, 2014.
［5］殷华锋, 徐小兵, 涂亚东, 等. 搅拌罐内固液两相流数值模拟研究现状［J］.化学工程与装备,2017(11):213-214.
YIN Huafeng, XU Xiaobing, TU Yadong, et al. Research Status of Numerical Simulation of Solid-Liquid Two-phase Flow in Stirred Tanks［J］. Chemical Engineering and Equipment, 2017(11):213-214.
［6］PENG C, FU Y Z, WEI H B, et al. Study on Improvement of Surface Roughness and Induced Residual Stress for Additively Manufactured Metal Parts by Abrasive Flow Machining［J］. Procedia CIRP,2018,71:386-389.
［7］ZHAO Zhongzhou, KAI Pingfeng, JU Longyuan, et al. A Wear Simulation of the Fixed Soft Abrasive Film Based on Discrete Element Method［J］. Advanced Materials Research, 2014, 1017:452-457.
［8］SCHMITT J, DIEBELS S. Simulation of the Abrasive flow Machining Process［J］. ZAMM Journal of Applied Mathematics & Mechanics, 2013, 93(2/3):147-153.
［9］李俊烨, 卢慧, 苏宁宁, 等. 大涡模拟Smagorinsky模型用于磨粒流精密加工喷嘴的质量控制研究［J］.中国机械工程，2020，31(10):1169-1174.
LI Junye, LU Hui, SU Ningning, et al. Research on Quality Control of Abrasive Flow Precision Machining Nozzles Based on Large Eddy Simulation Smagorinsky Model［J］. China Mechanical Engineering，2020，31(10):1169-1174.
［10］ZHANG Li, YUAN Zhimin, QI Zijian et al. CFD-based Study of the Abrasive Flow Characteristics within Constrained Flow Passage in Polishing of Complex Titanium Alloy Surfaces［J］. Powder Technology,2018,333:209-218.
［11］CHENG K, SHAO Y Z, JADVA M, et al. Development of the Improved Preston Equation for Abrasive Flow Machining of Aerofoil Structures and Components［J］. Proceedings of the Institution of Mechanical Engineers, 2019, 233(9):1397-1404.
［12］计时鸣,唐波,谭大鹏.基于VOF的模具结构化表面软性磨粒流数值模拟［J］.中国机械工程,2011,22(3):334-339.
JI Shiming, TANG Bo, TAN Dapeng. Numerical Simulation of Soft Abrasive Particle Flow on Structured Surface of Mold Based on VOF［J］. China Mechanical Engineering, 2011, 22(3): 334-339.
［13］PRESTON F. The Theory and Design of Plate Glass Polishing Machines［J］. Journal of the Society of Glass Technology, 1927, 11(44):214-256.
［14］李俊烨, 杨立峰, 刘薇娜, 等. 非直线管零件的磨粒流加工实验研究［J］. 中国机械工程, 2014, 25(13):1729-1734.
LI Junye, YANG Lifeng, LIU Weina, et al. Experimental Study on Abrasive Flow Processing of Nonlinear Pipe Parts［J］. China Mechanical Engineering, 2014, 25(13):1729-1734.

[1]	TUN Fu-Chao, TUN Bai-Hu, ZHANG Xiu-Hua. Numerical Simulation of Heat Transfer Performance of Paraffin Thermal-Sensitive Valve  [J]. J4, 201016, 21(16): 1921-1926.
[2]	GUO Wei, SUN Hongming, XU Gaofei, LI Guangwei, ZHOU Yue, WANG Minjian, . Improvements for Landing Impact Characteristics and Concentrated Stress Structures of Full Ocean Depth Landing Vehicles [J]. China Mechanical Engineering, 2021, 32(07): 867-874.
[3]	DU Fei;WANG Xinyun;DENG Lei;XIA Juchen;JIN Junsong. Research Progresses of HVIW Technology [J]. China Mechanical Engineering, 2021, 32(05): 600-610.
[4]	QIAO Wei1;YAO Weixing1,2. Numerical Analysis of Shear-lag Effect on Curing Deformation of Composites [J]. China Mechanical Engineering, 2021, 32(05): 611-616,623.
[5]	HU Jian1;CHEN Zezhong1;LIU Tao2;YANG Jinhua3. Simulation and Tests on Hot Forming Process Optimization for Door Anti-collision Beams [J]. China Mechanical Engineering, 2021, 32(01): 92-100.
[6]	HUA Shaozhen, MENG Fanjing, LIU Huabo, DING Hai. Study on Three Dimensional Simulation and Elimination Countermeasures of Melt Jetting Phenomenon in Injection Molding [J]. China Mechanical Engineering, 2020, 31(22): 2715-2722.
[7]	HU Mian;DING Xiaohong. Numerical and Experimental Investigations of Thermal Performance for Heat Pipe Ball Screws [J]. China Mechanical Engineering, 2020, 31(20): 2445-2453.
[8]	WANG Lin1;PAN Jun1;HE Qingchuan1;DING Wei2;GU Liwei2. Welding Process Optimization on Robot Welding of the Backward Centrifugal Fan Impeller [J]. China Mechanical Engineering, 2020, 31(19): 2379-2387.
[9]	WANG Guan1；ZHANG Qian2；KOU Linyuan1；LIU Zhiwen3；LI Shikang3. Nonlinear Topology Optimization of Continuum Structures Based on HCA Algorithm [J]. China Mechanical Engineering, 2020, 31(18): 2161-2173.
[10]	BAO Daorina；LIU Xujiang；WANG Xiaoxue；WANG Shuailong；LIU Jiawen. Analysis of Output Characteristics for Small Horizontal Axis Variable Eccentricity Wind Turbines [J]. China Mechanical Engineering, 2020, 31(18): 2196-2205.
[11]	TONG Zheming1；CHEN Yao1；TONG Shuiguang1；YU Yue1；LI Jinfu2；HAO Guoshuai3. Multi-objective Optimization Design of Low Specific Speed Centrifugal Pumps Based on NSGA-Ⅲ Algorithm [J]. China Mechanical Engineering, 2020, 31(18): 2239-2246.
[12]	SHEN Jianbang;XIAO Junhua;LIANG Xi;XU Yaoling. Numerical Study on In-plane Impact Dynamics of Negative Poisson's Ratio Honeycomb Structures with Curved Concave Sides [J]. China Mechanical Engineering, 2020, 31(16): 1998-2004.
[13]	SONG Shouxu1,2;HU Mengcheng1,2;DU Yi1,2;LUO Rundong1,2. Strain Numerical Simulation and Torque Imbalance Analysis of Remanufactured Motors with Mixed Stator Core [J]. China Mechanical Engineering, 2020, 31(09): 1080-1088.
[14]	ZOU Weisheng1 ;LIU Ruixian1;LIU Shaojun2. Study on Lifting Motor Pumps for Coarse Particle Slurry in Sea Bed Mining [J]. China Mechanical Engineering, 2019, 30(24): 2939-2944.
[15]	YUE Minnan1;LI Chun1,2;HAO Wenxing1;ZHANG Junwei1. Effects of Flap on Aerodynamic and Noise Characteristics of Airfoils [J]. China Mechanical Engineering, 2019, 30(12): 1409-1416.