Simulation and Analysis on Lubrication Performance of Surface Micro-Groove Texturing on Cylinder Liner in Diesel Engine

Abstract

Abstract:

Based on surface micro-groove texturing on cylinder liner, a mixed lubrication model of cylinder liner-piston ring was established, and the influence of micro-groove parameters on the lubrication performance was calculated by using MATLAB programming. The results show that the surface groove can form good film pressure, which effectively improves the lubrication state between cylinder liner and piston ring. And with the angle of micro-groove increases, the minimum oil ratio increases gradually, and the lubrication effect is getting better and better. Meanwhile synthetically considering the lubrication performance of friction and engine oil consumption performance, the best angle of micro-groove is affirmed as 60°. The changing of area density has great influence on the dimensionless friction force nearby the TDC, but has little influence on the other areas.Then the optimal area density is Sp=0.15. The dimensionless friction force increases continually with the increases of depth-to-width ratio, when e increases from 0.025 to 0.15, the average dimensionless friction force increases 2.3 times, and if the depth-to-width is too large, the lubrication effect will be weakened, the optimal depth-to-width ratio is as e=0.05~0.08.

Key words: cylinder liner;surface texturing, micro-groove, mixed lubrication model, lubrication

摘要：

针对缸套表面织构微沟槽形貌，建立了缸套-活塞环摩擦副混合润滑理论模型，并采用MATLAB编程计算来分析微沟槽形貌参数对其润滑摩擦性能的影响规律。结果表明：缸套表面微沟槽可以形成很好的油膜压力，有效地改善缸套-活塞环间的润滑状态;随着微沟槽角度的增大，最小膜厚比逐渐增大，其润滑效果也越来越好，综合考虑摩擦润滑性能和机油耗性能情况下，最佳的微沟槽角度为60°。在上止点附近，面积占有率变化Sp对量纲一摩擦力影响较大;在其他区域，面积占有率对摩擦力影响不大;综合考虑油膜厚度与摩擦力，当Sp=0.15时效果最好。随着微沟槽深宽比e的增大，量纲一摩擦力不断增大，当e从0.025增大到0.150时，平均量纲一摩擦力增大了2.3倍，但深宽比过大，润滑效果将会减弱。研究结果认为，最佳深宽比的范围为0.05~0.08。


关键词: 缸套, 表面织构, 微沟槽, 混合模型, 润滑

CLC Number:

TK421

YIN Bi-Feng, JIAN Yan-Jiang, LI Xiao-Dong, LIU Qing-Ji, FU Yong-Hong. Simulation and Analysis on Lubrication Performance of Surface Micro-Groove Texturing on Cylinder Liner in Diesel Engine[J]. China Mechanical Engineering, 2013, 24(5): 644-650.

尹必峰, 钱晏强, 李晓东, 刘胜吉, 符永宏. 柴油机缸套表面微沟槽织构润滑性能仿真分析[J]. 中国机械工程, 2013, 24(5): 644-650.

References

[1]华希俊，符永宏，王霄,等. 内燃机缸套激光珩磨技术及其能试验研究[J]. 中国机械工程，2007，18(24)：2989-2992.
Hua Xijun, Fu Yonghong, Wang Xiao, et al.Experimental Research on Laser Honing of Engine Cylinder Bore[J]. China Mechanical Engineering，2007，18(24)：2989-2992.
[2]Ronen A, Etsion I, Kligerman Y. Friction-reducing Surface-texturing in Reciprocating Automotive Components[J]. Tribol. Trans.，2001，44(3)：359-366.
[3]Sadeghi F,Wang C P. Advanced Natural Gas Reciprocating Engine: Parasitic Loss Control Through Surface Modification[R]. Cambridge:Mechanical Engineering Tribology Laboratory, 2005.
[4]Etsion I, Sher E. Improving Fuel Efficiency with Laser Surface Textured Piston Rings[J]. Tribology International，2009，42(4):542-547.
[5]符永宏，陆华才，华希俊,等. 激光微珩磨缸套润滑耐磨性能理论分析[J].内燃机学报，2006，24(6)：559-564.
Fu Yonghong，Lu Huacai，Hua Xijun. Theoretical Analysis on Lubrication and Wear-resisting of the Honed Cylinder Liner[J]. Transactions of Csice, 2006，24(6)：559-564.
[6]王晓雷，韩文非，加藤康司. 碳化硅陶瓷的水润滑特性及其表面微细织构的优化设计[J].中国机械工程，2008， 19(4)：457-460.
Wang Xiaolei， Han Wenfei，Kato Koji. Surface Texture Optimal Design for Silicon Carbide under Water Lubrication[J]. China Mechanical Engineering，2008， 19(4)：457-460.
[7]Patir N，Cheng H S. An Average Flow Model for Determining Effects of Three-dimensional Roughness on Partial Hydrodynamic Lubrication[J]. Trans. ASME，1978，100：12-18.
[8]Rohde S M. A Mixed Friction Model for Dynamically Loaded Contacts with Application to Piston Ring Lubrication[C]//Proc. of the 7th Leeds-Lyon Symposium on Tribology. Lyon，1980：262-278.

[1]	MA Qiaoying, YANG Shaopu, LIU Yongqiang, . Vibration and Lubrication Characteristics of Railway Vehicle Axle Box Bearings under Wheel-rail Excitation [J]. China Mechanical Engineering, 2024, 35(04): 580-590.
[2]	ZHANG Yu, WANG Dexiang, GUO Feng, LI Xinming, . Molecular Dynamics Study on Tribological Mechanism of Spherical Nanoparticles on Nickel-based Alloy Grinding Interfaces under Nanofluid MQL [J]. China Mechanical Engineering, 2024, 35(03): 445-456.
[3]	FU Zhenfeng, WANG Zhenzhong, WANG Biao. Research on Microfluidic Chip Fluid Dynamic Pressure Polishing Process [J]. China Mechanical Engineering, 2024, 35(03): 534-540.
[4]	ZHANG Lifeng, ZHANG Xiaoguang. Machining Performance and Material Removal Mechanism of High-speed Milling of CFRP with Variable Angle under Minimal Quantity Lubrication [J]. China Mechanical Engineering, 2023, 34(21): 2622-2628.
[5]	WEI Bingyang, GU Dewan, WANG Yongqiang, YANG Jianjun, . Friction Power Loss Analysis and Efficiency Test of High Reduction Hypoid Gears [J]. China Mechanical Engineering, 2023, 34(13): 1525-1532.
[6]	PAN Ling, LIN Guobin, HAN Yuqing, YU Hui. Molecular Dynamics Simulation for Effect of Nanoparticle Additives on Boundary Lubrication [J]. China Mechanical Engineering, 2023, 34(10): 1140-1156.
[7]	YE Shaogan, LAI Weiqun, HOU Liang, BU Xiangjian. Modeling and Experimental Validation of Lubrication Characteristics of Spherical Valve-plate Pairs with Conical Cylinder Block [J]. China Mechanical Engineering, 2022, 33(20): 2420-2428，2436.
[8]	LIAO Yihong, ZHANG Guiming, XU Jing. Influence Law and Mechanism of Texturized Controllable Interfaces on Leakage of Steam Turbine Regulating Valves [J]. China Mechanical Engineering, 2022, 33(12): 1427-1434.
[9]	LIANG Xingxin, ZHANG Sen, QI Shihuang, JIN Shuanbao. Experimental Study of Load Carrying Performance of Water Lubricated PCD Thrust Bearings for Rim Driven Thrusters [J]. China Mechanical Engineering, 2022, 33(12): 1452-1458，1467.
[10]	HAN Cuihong, MA Guozheng, LI Guolu, SHI Jiadong, WANG Haidou, . Tribological Properties of Mo/MoS2-Pb-PbS Composite Films in Vacuum Environments [J]. China Mechanical Engineering, 2022, 33(12): 1477-1483.
[11]	YU Guoda, LIU Huaiju, LU Zehua, WEI Peitang. Simulation and Experimental Study of Steady-state Temperature Field of Plastic Gears under Grease Lubrication Conditions#br# [J]. China Mechanical Engineering, 2022, 33(08): 890-898，907.
[12]	YANG Jianzhang, WANG Chengyong, YUAN Yaohui, YUAN Songmei, WANG Xibin, LIANG Cile, LI Weiqiu. State-of-the-art on MQL Synergistic Technologies and Their Applications [J]. China Mechanical Engineering, 2022, 33(05): 506-528.
[13]	LIU Mingzheng, LI Changhe, CAO Huajun, ZHANG Song, CHEN YunLIU Bo, ZHANG Naiqing, ZHOU Zongming. Research Progresses and Applications of CMQL Machining Technology [J]. China Mechanical Engineering, 2022, 33(05): 529-550.
[14]	WANG Dexiang, ZHAO Qiliang, ZHANG Yu, GAO Teng, JIANG Jingliang, LIU Guoliang, LI Changhe, . Investigation on Tribological Mechanism of Ionic Liquid on Grinding Interfaces under MQL [J]. China Mechanical Engineering, 2022, 33(05): 560-568，606.
[15]	LIANG Cile, YUAN Yaohui, WANG Chengyong, LI Weiqiu, YANG Jianzhang, WU Huayi. Study on Oil Mist Control and Oil Mist Particle Characteristics of MQL Systems [J]. China Mechanical Engineering, 2022, 33(05): 607-614.