随机风作用下风力发电机齿轮传动系统动载荷计算及统计分析

摘要/Abstract

摘要：

针对风力发电机齿轮传动系统在随机风作用下失效率高的问题，在模拟真实风速的基础上，建立考虑外部随机风载及内部齿轮时变啮合刚度、轴承时变刚度及综合传递误差等激励因素的风力发电机齿轮传动系统齿轮-轴承耦合动力学模型，通过对动力学模型进行仿真计算，得到各齿轮副的动态啮合力和各支承轴承的动态接触力。结合有限单元法和赫兹接触理论，得到关键零部件的应力时间历程，采用雨流计数法对应力时间历程进行统计分析，得到传动系统各关键零部件承受载荷的应力谱及概率分布函数。研究结果为风力发电机齿轮传动系统的动态可靠性分析和疲劳寿命预测奠定基础。

关键词: 风力发电机, 齿轮传动系统, 动力学, 动载荷, 统计分析

Abstract:

Aiming at the problems of high failure rate of wind turbines gear transmission system under the stochastic wind speed conditions, a dynamics model of gear transmission system coupled with bearing of wind turbine was established on the basis of simulating real wind speed, and the external random wind load and internal excitations such as time-varying mesh stiffness of gear pair, time-varying stiffness of rolling element bearings and integrated transmission errors were considered in the model. Numerical method was used to simulate the dynamics model, the dynamic meshing forces of each gear pair as well as the dynamic contact forces of each bearing were obtained. Then, the stress spectrum and the probability distribution function of the loads acting on the key parts of transmission system were obtained by statistic the stress-time history curves which was obtained by using the finite element method and the Hertz contact theory. This research results lay a foundation for dynamic reliability analysis and fatigue life prediction of the gear transmission system of a wind turbine.

Key words: wind turbine, gear transmission system, dynamics;dynamic load, statistical analysis

中图分类号:

徐芳, 周志刚. 随机风作用下风力发电机齿轮传动系统动载荷计算及统计分析[J]. 中国机械工程, 2016, 27(03): 290-295.

Xu Fang, Zhou Zhigang. Dynamic Load Calculation and Statistical Analysis of Gear Transmission System of Wind Turbine under Stochastic Wind Loading[J]. China Mechanical Engineering, 2016, 27(03): 290-295.

参考文献

[1]Guo Y，Keller J，LaCava W. Planetary Gear Load Sharing of Wind Turbine Drivetrains Subjected to Non-torque Loads[J]. Wind Energy，2014(4)：757-768.

[2]Musial W，Butterfield S，Mcniff B. Improving Wind Turbine Gearbox Reliability [C]//European Wind Energy Conference. Milano，2007: 1-13.

[3]李建林，肖志东，梁亮，等. 风能可再生能源与环境[M]. 北京:人民邮电出版社, 2010.

[4]窦真兰，王晗，张秋琼，等.虚拟风场和风力机模拟系统的实验研究[J].中国电机工程学报,2011， 31(20): 127-135.

Dou Zhenlan, Wang Han, Zhang Qiuqiong, et al. Experimental Research on Virtual Wind Farm and Wind Turbine Emulator System[J]. Proceedings of the Chinese Society for Electrical Engineering, 2011, 31(20): 127-135.

[5]Peeters J L M, Sas P, Vandepitte D. Analysis of Internal Drive Train Dynamics in a Wind Turbine[J]. Wind Energy, 2005,9:141-161.

[6]Liewa H V, Lim T C. Analysis of Time-varying Rolling Element Bearing Characteristics [J]. Journal of Sound and Vibration, 2005,283:1163-1179.

[7]秦大同，邢子坤，王建宏.基于动力学和可靠性的风力发电齿轮传动系统参数优化设计[J].机械工程学报，2008，44（7）：24-31.

Qin Datong，Xing Zikun，Wang Jianhong. Optimization Design of System Parameters of the Gear Transmission of Wind Turbine Based on Dynamics and Reliability[J]. Journal of Mechanical Engineering，2008，44（7）：24-31.

[8]谢里阳，刘建中，吴宁祥，等. 风电装备传动系统及零部件疲劳可靠性评估方法[J].机械工程学报，2014,50(11)：1-8.

Xie Liyang，Liu Jianzhong，Wu Ningxiang，et al. Fatigue Reliability Evaluation Method for Gearbox Component and System of Wind Turbine[J]. Journal of Mechanical Engineering，2014 ，50(11)：1-8.

[9]Tascikaraoglu A, Uzunoglu M. A Review of Combined Approaches for Prediction of Short- term Wind Speed and Power[J]. Renewable and Sustainable Energy Reviews, 2014, 34(6):243- 254.

[10]秦大同，周志刚，杨军，等. 随机风载作用下风力发电机齿轮传动系统动态可靠性分析[J]. 机械工程学报，2012, 48(3): 1- 8.

Qin Datong，Zhou Zhigang，Yang Jun，et al. Time- dependent Reliability Analysis of Gear Transmission System of Wind Turbine under Stochastic Wind Load[J]. Journal of Mechanical Engineering, 2012, 48(3):1- 8.

[11]Lim T C, Singh R. Vibration Transmission through Rolling Element Bearings, Part Ⅱ: System Studies[J]. Journal of Sound and Vibration, 1990,139(2): 201-205.

[12]Lin J. Analytical Investigation of Planetary Gear Dynamics[D]. Columbus: the Ohio State University, 2000.

[13]徐芳，周志刚，李迎春，等. 基于动力学的风电增速箱多级齿轮传动系统可靠性评估[J].中国机械工程，2014,25（9）：1219-1224.

Xu Fang，Zhou Zhigang，Li Yingchun，et al. Reliability Assessment of Multi-stage Gears Transmission System of Wind Power Growth Gearbox Based on Dynamics[J]. China Mechanical Engineering，2014，25（9）：1219-1224.

[14]冈本纯三.球轴承的设计计算[M]. 黄志强，译.北京：机械工业出版社，2003.

[1]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[2]	康爽, 陈长征, 赵思雨, 罗园庆, 孔祥希. 自适应差异多尺度形态学的风力机叶片红外图像增强研究[J]. 中国机械工程, 2021, 32(07): 786-792.
[3]	李强, 郭辰光, 赵丽娟, 冷岳峰, 岳海涛. 具有晶体学各向异性特征的DD5镍基单晶高温合金铣削力建模[J]. 中国机械工程, 2021, 32(06): 734-740.
[4]	宿月文;郭彩霞. 摆线传动接触载荷与效率的关联模式及试验验证[J]. 中国机械工程, 2021, 32(05): 556-564.
[5]	王志强, 雷震宇, . [轮轨磨耗及预测]地铁直线轨道钢轨波磨影响参数研究[J]. 中国机械工程, 2021, 32(04): 420-430.
[6]	俞轲鑫1；尚群立1；吴欣2. 节流孔板空化特性分析[J]. 中国机械工程, 2021, 32(03): 290-296.
[7]	范大鹏;谭若愚. 快速反射镜中柔顺传动机构应用与研究现状[J]. 中国机械工程, 2020, 31(24): 2899-2909.
[8]	张宁;李田;殷国栋;吴建华;赵子乾. 转向系参数对汽车拖车组合系统稳定性的影响[J]. 中国机械工程, 2020, 31(21): 2521-2528.
[9]	郭金生1;王峰1;岳程斐2. 基于商用现货的高分辨卫星微振动抑制系统设计[J]. 中国机械工程, 2020, 31(20): 2395-2042，2411.
[10]	程加远;任廷志;张子龙;刘大伟;金昕. 惯性圆锥破碎机多体动力学分析及试验验证[J]. 中国机械工程, 2020, 31(19): 2322-2331.
[11]	刘大伟1，2；刘佳佳1. 面向管道机器人的非对称惯性驱动系统及其动力学特性[J]. 中国机械工程, 2020, 31(18): 2189-2195，2205.
[12]	谭飏1；张宇2；刘丽冰1；杨泽青1. 面向动力学特性监测的主轴系统数字孪生体[J]. 中国机械工程, 2020, 31(18): 2231-2238，2246.
[13]	王均山;陈超;石明友;曹静. 悬浮式球转子压电作动器的设计及实验研究[J]. 中国机械工程, 2020, 31(17): 2064-2070.
[14]	王明远1;杭鲁滨1;刘哲2;黄晓波1;陈勇2;缪宏3. 含变自由度力自适应复位组合柔顺副的汽车门锁机构[J]. 中国机械工程, 2020, 31(12): 1437-1443.
[15]	葛文韬;黄晖;刘洲;邱星;贾慧芳. 一种加速多体动力学模型虚拟迭代的载荷谱编制方法[J]. 中国机械工程, 2020, 31(12): 1504-1511.