17-4PH不锈钢挤出成形制品的疲劳性能

doi:10.3969/j.issn.1004-132X.2025.07.021

中国机械工程 ›› 2025, Vol. 36 ›› Issue (07): 1582-1591.DOI: 10.3969/j.issn.1004-132X.2025.07.021

17-4PH不锈钢挤出成形制品的疲劳性能

姜世杰^1,2*;蔡尚港¹;英洪玮¹;陈佳琦¹

1.东北大学机械工程与自动化学院，沈阳，110819
2.辽宁省机械装备动力学可靠性重点实验室，沈阳，110819

出版日期:2025-07-25 发布日期:2025-09-04
作者简介:姜世杰*，男，1985年生，副教授，博士。研究方向为熔丝成型增材制造技术。发表论文50余篇。 E-mail:jiangsj@me.neu.edu.cn。
基金资助:
国家自然科学基金（52475093）；省部级基金项目（2023-MSBA-028）

Fatigue Property of 17-4PH Products Fabricated via Metal Material Extrusion Technique

JIANG Shijie1,2*;CAI Shanggang1;YING Hongwei1;CHEN Jiaqi1

1.School of Mechanical Engineering & Automation, Northeastern University,Shenyang,110819
2.Key Laboratory of Dynamics Reliability of Mechanical Equipment of Liaoning Province,
Shenyang,110819

Online:2025-07-25 Published:2025-09-04

摘要/Abstract

摘要： 随着金属材料挤出成形产品应用范围的扩大，为确保可靠性和安全性，须研究其疲劳性能。建立了考虑成形方向和填充角度的金属材料挤出成形烧结制品损伤疲劳寿命预测模型。制备了不同成形方向和填充角度的金属材料挤出成形烧结试件，并对其完成了密度、收缩率、拉伸性能和疲劳性能的研究。结果表明：疲劳寿命的理论值与实验值的误差为1.50%~11.83%，验证了所建模型的正确性；试件烧结后的尺寸收缩率、拉伸性能和疲劳性能呈各向异性。

关键词: 金属材料挤出成形, 预测模型, 疲劳性能, 拉伸性能, 填充角度, 成形方向

Abstract: With the expansion of the application rangs of metal material extrusion products, it was urgent to investigate their fatigue property to ensure the reliability and safety. A damage fatigue life prediction model for metal material extrusion sintered products was established considering forming orientations and filling angles. Metal material extrusion sintered specimens with different forming orientations and filling angles were fabricated, and their density, shrinkage rate, tensile property and fatigue property were studied. The results show that the errors between predicted and measured fatigue life are as from 1.50% to 11.83%, which validates the correctness of the proposed model, while the shrinkage rate, tensile property, and fatigue property of the sintered specimens exhibite anisotropy.

Key words: metal material extrusion, prediction model, fatigue property, tensile property, filling angle, forming orientation

中图分类号:

TG142.71

姜世杰1, 2, 蔡尚港1, 英洪玮1, 陈佳琦1. 17-4PH不锈钢挤出成形制品的疲劳性能[J]. 中国机械工程, 2025, 36(07): 1582-1591.

JIANG Shijie1, 2, CAI Shanggang1, YING Hongwei1, CHEN Jiaqi1. Fatigue Property of 17-4PH Products Fabricated via Metal Material Extrusion Technique[J]. China Mechanical Engineering, 2025, 36(07): 1582-1591.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2025.07.021

https://www.cmemo.org.cn/CN/Y2025/V36/I07/1582

参考文献

［1］ROSHCHUPKIN S, KOLESOV A, TARAKHOVSKIY A, et al. A Brief Review of Main Ideas of Metal Fused Filament Fabrication［J］. Materials Today:Proceedings, 2021, 38:2063-2067.
［2］BANKAPALLI N K, GUPTA V, SAXENA P, et al. Filament Fabrication and Subsequent Additive Manufacturing, Debinding, and Sintering for Extrusion-based Metal Additive Manufacturing and Their Applications:a Review［J］. Composites Part B:Engineering, 2023, 264:110915.
［3］DAMON J, DIETRICH S, GORANTLA S, et al. Process Porosity and Mechanical Performance of Fused Filament Fabricated 316L Stainless Steel［J］. Rapid Prototyping Journal, 2019, 25(7):1319-1327.
［4］CARMINATI M, QUARTO M, DURSO G D, et al. A Comprehensive Analysis of AISI 316L Samples Printed via FDM:Structural and Mechanical Characterization［J］. Key Engineering Materials, 2022, 926:46-55.
［5］GODEC D, CANO S, HOLZER C, et al. Optimization of the 3D Printing Parameters for Tensile Properties of Specimens Produced by Fused Filament Fabrication of 17-4PH Stainless Steel［J］. Materials, 2020, 13(3):774.
［6］CAMINERO M , ROMERO GUTIRREZ A, CHACN J M, et al. Effects of Fused Filament Fabrication Parameters on the Manufacturing of 316L Stainless-steel Components:Geometric and Mechanical Properties［J］. Rapid Prototyping Journal, 2022, 28(10):2004-2026.
［7］KEDZIORA S, DECKER T, MUSEYIBOV E, et al. Strength Properties of 316L and 17-4 PH Stainless Steel Produced with Additive Manufacturing［J］. Materials, 2022, 15(18):6278.
［8］SPILLER S, OLSYBAKK KOLSTAD S, RAZAVI N. Fatigue Behavior of 316L Stainless Steel Fabricated via Material Extrusion Additive Manufacturing［J］. Engineering Fracture Mechanics, 2023, 291:109544.
［9］JIANG Dayue, NING Fuda. Additive Manufacturing of 316L Stainless Steel by a Printing-Debinding-Sintering Method:Effects of Microstructure on Fatigue Property［J］. Journal of Manufacturing Science and Engineering, 2021, 143(9):091007.
［10］GHADIMI H, JIRANDEHI A P, NEMATI S, et al. Effects of Printing Layer Orientation on the High-frequency Bending-fatigue Life and Tensile Strength of Additively Manufactured 17-4 PH Stainless Steel［J］. Materials, 2023, 16(2):469.
［11］文磊, 罗周全, 杨仕教, 等. 岩体损伤度的点荷载强度计算及分析［J］. 工程科学学报, 2017, 39(2):175-181.
WEN Lei, LUO Zhouquan, YANG Shijiao, et al. Analyses and Calculation of Point Load Strength on Rock Mass Damage Index［J］. Chinese Journal of Engineering, 2017, 39(2):175-181.
［12］JIANG Shijie, LI Shuo, CAI Shanggang, et al. Theoretical and Experimental Study on the Fatigue Property of Material Extrusion Products and Improvement by Using Vibration Machining during Manufacturing Process［J］. International Journal of Fatigue, 2024, 182:108193.
［13］LONARD F, TAMMAS-WILLIAMS S. Metal FFF Sintering Shrinkage Rate Measurements by X-ray Computed Tomography［J］. Nondestructive Testing and Evaluation, 2022, 37(5):631-644.
［14］GONZALEZ-GUTIERREZ J, ARBEITER F, SCHLAUF T, et al. Tensile Properties of Sintered 17-4PH Stainless Steel Fabricated by Material Extrusion Additive Manufacturing［J］. Materials Letters, 2019, 248:165-168.
［15］SINGH G, MISSIAEN J M, BOUVARD D, et al. Additive Manufacturing of 17-4 PH Steel Using Metal Injection Molding Feedstock:Analysis of 3D Extrusion Printing, Debinding and Sintering［J］. Additive Manufacturing, 2021, 47:102287.
［16］屈聪, 孟智娟, 赵亮, 等. 基于变弹性模量的Ti-6Al-4V板材五点弯曲回弹预测［J］. 中国机械工程, 2022, 33(16):1991-1999.
QU Cong, MENG Zhijuan, ZHAO Liang, et al. Prediction of Five-point Bending Springback of Ti-6Al-4V Plates Based on Variable Elastic Modulus［J］. China Mechanical Engineering, 2022, 33(16):1991-1999.
［17］王勇刚, 郭一冰, 董逸君, 等. 基于分形维数的预腐蚀铝合金疲劳寿命预测［J］. 机械工程材料, 2022, 46(12):79-84.
WANG Yonggang, GUO Yibing, DONG Yijun, et al. Fatigue Life Prediction of Pre-corroded Aluminum Alloy Based on Fractal Dimension Method［J］. Materials for Mechanical Engineering, 2022, 46(12):79-84.

[1]	张建宇, 王留震, 肖勇, 马雅楠. 滚动轴承的退化特征信息融合与剩余寿命预测[J]. 中国机械工程, 2025, 36(07): 1553-1561.
[2]	雷付煜1, 徐小旭2, 赵亚明2, 罗军1, 马超1, 徐从昌1, 李落星13. 加载角度对6082铝合金自冲铆接接头疲劳性能及失效模式的影响[J]. 中国机械工程, 2025, 36(01): 141-151.
[3]	党旭, 刘涛, 闫敏, 安锋. 薄壁复杂变截面涡旋盘精密铣削组合参数优选与铣削力准确预测[J]. 中国机械工程, 2024, 35(11): 1963-1970.
[4]	靳淇超1, 2, 包虎子1, 李良万3, 汪文虎3, 张锦淇1, 叶子银1, 郭磊1. DD5缓进磨削表面粗糙度和硬化率对疲劳性能影响研究[J]. 中国机械工程, 2024, 35(08): 1472-1479.
[5]	董志波1, 王程程1, 李承昆1, 李峻臣2, 赵耀邦2, 历吴恺2, 徐爱杰2. 复杂载荷、极端环境下焊接结构疲劳寿命预测研究综述[J]. 中国机械工程, 2024, 35(05): 829-839.
[6]	程基彬, 戴宁, 郭培, 熊继源, 叶世伟, 程筱胜. 基于力学超材料的柔性机械臂设计技术[J]. 中国机械工程, 2023, 34(16): 1900-1906.
[7]	陈昱, 项薇, 龚川. 基于数据挖掘的注塑产品质量在线故障检测及预测[J]. 中国机械工程, 2023, 34(14): 1749-1755.
[8]	向柔潼, 王时龙, 周杰, 易力力. 辐照环境下新型气动位置传感器压力响应特性研究[J]. 中国机械工程, 2023, 34(11): 1364-1371.
[9]	张瑾, 韩福柱, . 电弧铣削加工间隙电压预测模型的建立与研究[J]. 中国机械工程, 2022, 33(16): 1891-1896.
[10]	倪恒欣, 阎春平, 孙菡, 徐腾, 黄一躬, 周超. 高速干切滚齿机床能耗分布特性及其预测模型[J]. 中国机械工程, 2022, 33(07): 842-851.
[11]	齐振超, 肖叶鑫, 王星星, 陈文亮. Ti45Nb铆钉脉冲电流辅助压铆成形性能分析[J]. 中国机械工程, 2021, 32(23): 2832-2839，2849.
[12]	刘小峰, 谭奇, 叶蓉婷. 基于优化特征的集成变量预测模型及其应用[J]. 中国机械工程, 2021, 32(18): 2153-2158，2164.
[13]	文东辉, 许鑫祺, 郑子军. 线性液动压抛光流场的剪切特性研究[J]. 中国机械工程, 2021, 32(18): 2203-2210，2216.
[14]	姜云禄, 杨亮, 韩晓辉, 徐野, 陈怀宁, 蔡桂喜. 运行条件对不锈钢点焊疲劳性能影响及开裂分析[J]. 中国机械工程, 2021, 32(14): 1726-1731.
[15]	唐凯1;周留成2;何卫峰2;王文健1;郭俊1;刘启跃1. 激光冲击强化对LZ50车轴钢疲劳性能影响试验研究[J]. 中国机械工程, 2020, 31(03): 267-273.

17-4PH不锈钢挤出成形制品的疲劳性能

Fatigue Property of 17-4PH Products Fabricated via Metal Material Extrusion Technique

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics