基于SH模态导波杆的电站高温结构壁厚测量方法

中国机械工程

基于SH模态导波杆的电站高温结构壁厚测量方法

徐鸿;郭鹏;李鸿源;田振华;邓博

华北电力大学能源动力与机械工程学院，北京，102206

出版日期:2017-04-10 发布日期:2017-04-07
基金资助:
国家自然科学基金资助项目（51134016）;
中央高校基本科研业务费专项资金资助项目（2016XS25）

Thickness Measuring Method of High-temperature Power Plant Structures Based on SH Mode Waveguide

XU Hong ;GUO Peng;LI Hongyuan;TIAN Zhenhua;DENG Bo

School of Energy, Power and Mechanical Engineering, North China Electric Power University, Beijing,102206

Online:2017-04-10 Published:2017-04-07
Supported by:

摘要/Abstract

摘要： 提出了一种基于SH模态导波杆的电站高温结构壁厚测量方法，该方法使用导波杆将压电传感器与高温被测结构隔开。通过研究发现非频散SH模态导波能通过矩形横截面导波杆将导波信号由传感器导入到高温被测结构中。实验验证了通过特定夹具以干耦合方式将导波杆固定在被测结构表面可以获得较好的信号。使用2MHz中心频率下的汉宁窗调制正弦波信号实现了对处于不同温度被测结构壁厚的监测，室温（25℃）时，壁厚测量值与实际厚度相差0.016mm，高温被测结构实验信号也非常好，波速测量值与拟合曲线所得速度值误差范围为0.1%～2.5%。

关键词: 超声导波, SH0模态, 导波杆, 高温, 壁厚监测, 数值模拟

Abstract: It is significant to put forward a thickness measuring method of high temperature power plant structures based on SH mode, which used a waveguide to isolate the transducers from the high-temperature measurement zones. It was found that a nondispersive SH mode guided wave in rectangular waveguide was employed to transmit the guided wave signals from the transducers to the measurement zones. In addition, experiments were investigated by dry-coupled to attach the waveguides to the components, which shows that clamping the waveguides to the component surfaces may get best results. By using Hanning window modulated sine wave signals with 2MHz center frequency, the thickness difference of the measured values and actual values of wall thickness is 0.016mm at the room temperature(25℃). Performance at high temperatures was tested without signal degradation. The error ranges of wave velocity measurement values and the velocities of the fitting curve are 0.1% to 2.5%.

Key words: ultrasonic guided wave, SH0 mode, waveguide, high temperature, thickness monitoring, numerical simulation

中图分类号:

TB559
O347.4

徐鸿, 郭鹏, 李鸿源, 田振华, 邓博. 基于SH模态导波杆的电站高温结构壁厚测量方法[J]. 中国机械工程.

XU Hong , GUO Peng, LI Hongyuan, TIAN Zhenhua, DENG Bo. Thickness Measuring Method of High-temperature Power Plant Structures Based on SH Mode Waveguide[J]. China Mechanical Engineering.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/

https://www.cmemo.org.cn/CN/Y2017/V28/I07/757

参考文献

[1]田振华, 徐鸿, 李鸿源, 等. 基于单激发端多接收端压电阵列的板内损伤检测[J]. 中国机械工程,2014,25(22): 3077-3080,3087.
TIAN Zhenhua, XU Hong, LI Hongyuan, et al. Damage Detection for a Plate Based on a Single-transmitter Multi-receiver PZT Array[J]. China of Mechanical Engineering, 2014,25(22):3077-3080，3087.
[2]田振华, 徐鸿, 杨志磊. 基于扭转模态的管道裂纹聚焦成像[J]. 中国机械工程, 2013,24(1):85-89.
TIAN Zhenhua, XU Hong, YANG Zhilei. Focusing Imaging of Cracks in Pipes Based on Torsional Modes[J]. China of Mechanical Engineering,2013,24(1):85-89.
[3]MCNAB A, KIRK K J, COCHRAN A. Ultrasonic Transducers for High Temperature Applications [J]. Science Measurement and Technology, IEE Proceedings,1998,145:229-236.
[4]TITTMANN B, AASLAN M. Ultrasonic Sensors for High Temperature Applications [J]. Japanese Journal of Applied Physics,1999,38(5):3011-3013.
[5]CAWLEY P, CEGLA F B. Ultrasonic Non-destructive Testing: U.S. Patent 8381592[P].2013-02-26
[6]LYNNWORTH L C, LIU Y, UMINA J A. Extensional Bundle Waveguide Techniques for Measuring Flow of Hot Fluids[J]. IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control,2005,52(4):538-544.
[7]李金红,张雅超，邸艳玲，等.采用导波杆方式超声检测高温高压管道壁厚的方法[J].NDT无损检测，2009,31（8）：593-595,599.
LI Jinhong, ZHANG Yachao, DI Yanling, et al. Ultrasonic Thickness Measurement Method for High Pressure and Temperature Tube by Waveg-uide Bar[J]. Nondestructive Testing, 2009, 31(8):593-595,599.
[8]YOUNGDAHL C A, ELLINGSON W A. Nondestructive Monitoring of Erosive Wear at Synfuels Pilot Plants[J]. Mater. Performance(United States),1985,24(1):48-53.
[9]ROSE J L. Ultrasonic Waves in Solid Media［M］. Cambridge: Cambridge University Press,1999.
[10]GIURGIUTIU V. Structural Health Monitoring with Piezoelectric Wafer Active Sensors［M］. Boston, MA: Academic Press, 2008.
[11]CEGLA F. Energy Concentration at the Center of Large Aspect Ratio Rectangular Waveguides at High Frequencies\[J\]. The Journal of the Acoustical Society of America, 2008,123(6):4218-4226.

[1]	余昶锐, 刘良宝, 周靖刚, 张函, 黄东, 张宁, 李勋. 面向涡轮盘榫槽凹圆弧表面的滚压参数优化[J]. 中国机械工程, 2026, 37(1): 60-65.
[2]	付博宇, 许泽华, 李康帅, 王浩宇, 贺嘉琪, 何强. 高海拔环境下无人机螺旋桨流场与电机温度场的数值模拟与试验分析[J]. 中国机械工程, 2025, 36(12): 2894-2902.
[3]	李颂华, 薛宝圆, 左闯. Si₃N₄耐高温全陶瓷向心关节轴承磨损性能研究[J]. 中国机械工程, 2025, 36(09): 1989-1995.
[4]	张鹏1, 3, 4, 5, 朱学卫2, 3, 4, 于保洋1, 3, 4, 武天枫1, 3, 4, 朱锦州1, 3, 4. 304不锈钢极薄带微流道气胀成形材料流动行为及微观组织[J]. 中国机械工程, 2025, 36(07): 1416-1422.
[5]	何喆1, 李佳乐1, 史恺宁1, 樊昱昌3, 黄新春2. 热机载荷下GH4169G车削喷丸加工表面完整性的演化机理[J]. 中国机械工程, 2025, 36(04): 780-789.
[6]	范治松, 李宁, 徐立凯, 邓将华. 6063铝/20钢管磁脉冲胀形连接工艺研究[J]. 中国机械工程, 2024, 35(12): 2185-2192.
[7]	靳淇超1, 2, 包虎子1, 李良万3, 汪文虎3, 张锦淇1, 叶子银1, 郭磊1. DD5缓进磨削表面粗糙度和硬化率对疲劳性能影响研究[J]. 中国机械工程, 2024, 35(08): 1472-1479.
[8]	张金阳, 许伟春, 王笑含, 江小辉, 高山. 铣削工艺优化对镍基高温合金加工残余应力分布影响研究[J]. 中国机械工程, 2024, 35(04): 624-635.
[9]	李燕乐, 潘忠涛, 戚小霞, 崔维强, 陈健, 李方义. 热处理工艺对激光熔覆316L温度场与应力场的影响规律[J]. 中国机械工程, 2024, 35(04): 666-677.
[10]	彭文飞, 张成, 林龙飞, 黄明辉, 余丰. 基于连续损伤力学的楔横轧芯部损伤建模及预测[J]. 中国机械工程, 2024, 35(04): 711-720,751.
[11]	崔海涛, 钱春华. 镍基高温合金的热机械疲劳寿命预测模型研究[J]. 中国机械工程, 2024, 35(01): 67-73,82.
[12]	勾睿杰, 张晓峰, 张鸿滨, 姚俊, 李勋. 刀具磨损对Allvac 718Plus高温合金铣削加工表面完整性及疲劳性能的影响[J]. 中国机械工程, 2023, 34(24): 2920-2926.
[13]	李坤航, 张思琦, 吴玮, 胡明卓, 孙娅铃, 熊鑫, 黄宏. 三层异种不等厚钢电阻点焊多场耦合模拟与分析[J]. 中国机械工程, 2023, 34(24): 2996-3003.
[14]	马预谱, 魏涛, 王力, 赵俊熠, 张鑫磊, 陈妮, 李亮, 何宁. 氮化铝基板嵌入式微流道设计及激光刻蚀研究[J]. 中国机械工程, 2023, 34(20): 2496-2503.
[15]	张明亮, 杨大伟, 李明远, 杨新梦, 刘丽茹, 张连朋. 永磁轨道参数优化和悬浮力特性研究[J]. 中国机械工程, 2023, 34(19): 2370-2380.