Investigation on Measurement Method of Dynamic Response Time for an Electronic Fuel Injector

China Mechanical Engineering ›› 2012, Vol. 23 ›› Issue (5): 626-628.

Investigation on Measurement Method of Dynamic Response Time for an Electronic Fuel Injector

Guo Hui1, 2;Zhang Zhendong1;Cheng Qiang1;Sun Yuedong1

1.University of Shanghai for Science and Technology, Shanghai, 200093

2.Shanghai University of Engineering Science, Shanghai, 201620

Online:2012-03-10 Published:2012-03-21
Supported by:

Research Fund for the Doctoral Program of Higher Education of China
（No. 200802520001）

一种电控喷油器动态时间参数测试方法

郭辉1,2;张振东1;程强1;孙跃东1

1.上海理工大学,上海,200093

2.上海工程技术大学,上海,201620

基金资助:
高等学校博士学科点专项科研基金资助项目 (200802520001)；上海市科委科技攻关计划项目(10230501500)；上海市高校选拔培养优秀青年教师科研专项基金资助项目(GJD08005)；上海市研究生创新基金项目(JWCXSL1001)
Research Fund for the Doctoral Program of Higher Education of China（No. 200802520001）

Abstract

Abstract:

The dynamic working process of an EFI was analyzed in detail.According to the current curve through the coil of the EFI,a measurement method of the dynamic response time for the EFI was provided.Then the test circuits of the opening and closing response time of the injector were designed,and the measurement system was developed with the C8051F310 as the processor.And the measurement system is low cost,convenient and high precision.The results show that the measurement errors of the opening and closing response time of the EFI are 0.9% and 1.14% respectively,and this meets to the testing requirements of design and research,manufacture of the injector.Meanwhile, the curves of opening response time with the supply voltage were provided,the injection quantity can be amended when the engine was calibrated.

Key words: electronic fuel injector(EFI), dynamic characteristics, measurement, system design

摘要：

详细分析了电控喷油器的动态工作过程,基于电控喷油器线圈电流变化规律,提出一种测试其动态响应时间的方法。以高性能C8051F310单片机为处理器,设计了喷油器开启与关闭响应时间的测试电路,开发了成本低、测试便捷、精度高的测试系统。实测结果表明,喷油器的开启与关闭的响应时间测量误差分别为0.9%和1.14%,满足喷油器设计开发、生产的要求。同时,给出了开启响应时间随供电电压的变化关系曲线,该曲线为电控喷油器标定及发动机匹配时对喷油量的修正提供了参考。

关键词:

电控喷油器, 动态性能, 测试, 系统设计



CLC Number:

TK411.5

GUO Hui-1, 2, ZHANG Zhen-Dong-1, CHENG Jiang-1, SUN Ti-Dong-1.

Investigation on Measurement Method of Dynamic Response Time for an Electronic Fuel Injector

[J]. China Mechanical Engineering, 2012, 23(5): 626-628.

郭辉1, 2, 张振东1, 程强1, 孙跃东1.

一种电控喷油器动态时间参数测试方法

[J]. 中国机械工程, 2012, 23(5): 626-628.

[1]	DIAO Jin-Chao, WANG Bang-Feng, MAO Chang-Wei, NING Su-Juan. Research on Tensile Deformation and Strain of Composite Corrugated Skin [J]. J4, 201016, 21(16): 1959-1963.
[2]	YANG Jisen, ZHOU Run, ZHANG Tianheng, LU Yu, WU Zhuo, ZHANG Di, ZHANG Jing. Research on Magnetic Field Compensated Double-layer Time-grating Angular Displacement Sensors under Structural Parameter Constraints [J]. China Mechanical Engineering, 2023, 34(19): 2296-2303，2312.
[3]	SUN Jiale, LUO Chen, ZHOU Yijun, WANG Wei, ZHANG Gang. Calibration Parameter Optimization and Accuracy Evaluation of Complex Visual Measurement Systems [J]. China Mechanical Engineering, 2023, 34(14): 1741-1748,1755.
[4]	LI Ruijun, DUAN Liuhui, ZHAO Wenkai, CHENG Zhenying, FAN Guangzhao. High-precision Microsphere Radius Measurement Model and Comparation among Roundness Evaluation Methods [J]. China Mechanical Engineering, 2023, 34(10): 1159-1163,1171.
[5]	GAO Xin, YE Nan, ZHOU Kun, TAO Yourui, . Two Stage Wiener Modeling and Reliability Analysis Considering Measurement Errors [J]. China Mechanical Engineering, 2023, 34(09): 1067-1076.
[6]	SUN Luping, ZHANG Wenchang, WANG Zhihua, WANG Zhenwen, REN Zhimo, ZHANG Qian, . Measurement Method of Cabin Automatic Docking Based on 2D Laser Displacement Sensor [J]. China Mechanical Engineering, 2023, 34(09): 1120-1125,1133.
[7]	WANG Haitong, REN Zixiao, LIU Zhihua, CAI Chenguang, CAI Yonglin, . Spatio-temporal Consistency Technology for Inertial Measurement of Guide Rail Straightness [J]. China Mechanical Engineering, 2023, 34(08): 916-922.
[8]	FU Gaocai, SHENG Buyun, WAN Run, YIN Xiyan, SHENG Ganlin. An ER-BFGS Evaluation Method for Datum-free Profile of Complex Surfaces [J]. China Mechanical Engineering, 2023, 34(08): 923-930.
[9]	LIN Xin, ZHANG Jie, FENG Jingyi, MENG Jie, WANG Shuting. Highly Robust Two-stage LiDAR-IMU External Parameter Online Calibration Algorithm [J]. China Mechanical Engineering, 2022, 33(24): 2980-2989.
[10]	JIANG Jinyu, SUN Dan, ZHAO Huan, ZHANG Guochen, LI Yu, WEN Shuaifang. Study on Leakage Characteristics and Dynamic Characteristics of New Type of Vortex Groove Seals [J]. China Mechanical Engineering, 2022, 33(19): 2306-2316.
[11]	ZHOU Xin, LI Geqiang, LEI Xianqing, XU Zengjian. Analysis of a Full Hydraulic Power Steering System with Integrated Power Regeneration Module [J]. China Mechanical Engineering, 2022, 33(18): 2227-2233.
[12]	LYU Jingcheng, WEI Yintao, WU Mingyu, HE Junxiang, LIANG Guanqun, YIN Hang. Hysteresis and Dynamic Response of Magnetorheological Measuring Systems [J]. China Mechanical Engineering, 2022, 33(17): 2017-2023.
[13]	HOU Liang, GUO Jing, CHEN Yun, YE Chao, XU Yang, ZOU Jiahao. Subtractive Post-machining Allowance Optimization Considering Characteristics of DEDs [J]. China Mechanical Engineering, 2022, 33(17): 2098-2106.
[14]	SHI Zhaoyao, YU Bo, SONG Huixu, WANG Xiaoyi. Development of Gear Measurement Technology during Last 20 Years [J]. China Mechanical Engineering, 2022, 33(09): 1009-1024.
[15]	PENG Donglin, SHI Zhaoyao, ZHENG Yong, ZHOU Qiwu, YANG Jisen, XU shi. Research on Complete Set Technology of Ultra-precision Worm Gear Pair [J]. China Mechanical Engineering, 2022, 33(09): 1051-1056.