Identification Approach of Geometrical Parameters for Non-contact Five-coordinate Measuring Machine

China Mechanical Engineering ›› 2014, Vol. 25 ›› Issue (23): 3147-3150.

Previous Articles Next Articles

Identification Approach of Geometrical Parameters for Non-contact Five-coordinate Measuring Machine

Fei Zhigen1;Xu Xiaojie2;Guo Junjie3

1.Zhengzhou University of Light Industry,Zhengzhou,450002
2.Henan Polytechnic University,Jiaozuo,Henan,454000
3.State Key Laboratory for Manufacturing Systems Engineering,Xi'an Jiaotong University,Xi'an,710049

Online:2014-12-10 Published:2014-12-12
Supported by:
Henan Provincial Key Technology R&D Program of Ministry of Education of China（No. 13A460377）

非接触式五坐标测量机系统几何参数的辨识方法

费致根1;徐小洁2;郭俊杰3

1.郑州轻工业学院，郑州，450002
2.河南理工大学，焦作，454000
3.西安交通大学机械制造系统工程国家重点实验室，西安，710049

基金资助:
河南省教育厅科技攻关项目（13A460377）；河南省高等学校精密制造技术与工程重点学科开放实验室开放基金资助项目（PMTE201304A）；郑州轻工业学院博士科研基金“青骨”项目

Abstract

Abstract:

Aiming at the exploited non-contact five-coordinate measuring machine with laser probe, its overall structure and working principles were introduced. The measurement mathematical model of such system was established by virtue of multi-body kinematics theory and homogeneous transformation. For the unknown geometrical parameters in this model, the identification approaches were proposed based on testing the physical basis. The experimental results show that the method is valid and feasible. The identification repeated errors of three system geometrical parameters are all within 2μm.

Key words: five-coordinate measuring machine, parameter identification, non-contact measurement, laser measurement

摘要：

针对所研发的非接触式五坐标测量机，介绍了其系统组成及工作原理。采用多体运动学理论与齐次坐标变换的方法建立了系统的测量数学模型。对于数学模型中的未知几何参数，提出了基于测量实物基准的参数辨识方法，实现了对三个未知几何参数的辨识。实验结果表明该方法是有效、可行的，三个几何参数辨识的重复误差都在2μm以内。

关键词: 五坐标测量机, 参数辨识, 非接触式测量, 激光测量

CLC Number:

TG391.4

Fei Zhigen, Xu Xiaojie, Guo Junjie. Identification Approach of Geometrical Parameters for Non-contact Five-coordinate Measuring Machine[J]. China Mechanical Engineering, 2014, 25(23): 3147-3150.

费致根, 徐小洁, 郭俊杰. 非接触式五坐标测量机系统几何参数的辨识方法[J]. 中国机械工程, 2014, 25(23): 3147-3150.

References

[1]刘祚时, 倪潇娟. 三坐标测量机(CMM)的现状和发展趋势[J]. 机械制造, 2004(8): 32-34.
Liu Zuoshi, Ni Xiaojuan. The Status and Developing Trend of CMM[J].Machinery, 2004(8):32-34.
[2]张国雄. 坐标测量技术发展方向[J]. 红外与激光工程, 2008, 37(4): 1-5.
Zhang Guoxiong. Development Orientations of Coordinate Measuring Techniques[J]. Infrared and Laser Engineering,2008, 37(4): 1-5.
[3]Shamma J S, Whitney D E. A Method for Inverse Robot Calibration[J]. Transactions of the ASME, 1987, 109(1): 36-43.
[4]Santolaria J, Aguilar J, Yagre J,et al. Kinematic Parameter Estimation Technique for Calibration and Repeatability Improvement of Articulated Arm Coordinate Measuring Machines[J]. Precision Engineering, 2008, 32(4): 251-268.
[5]Park J J, Kwon K, Cho N. Development of a Coordinate Measuring Machine (CMM) Touch Probe Using a Multi-axis Force Sensor[J]. Measurement Science and Technology, 2006,17: 2380-2386.
[6]Lotze W. Multidimensional Measuring Probe Head Improves Accuracy and Functionality of Coordinate Measuring Machines[J]. Measurement, 1994, 13(2): 91-97.
[7]Dai G, Bütefisch S,Pohienz F, et al. A High Precision Micro/Nano CMM Using Piezoresistive Tactile Probes[J]. Measurement Science and Technology,2009, 20(8): 1-9.
[8]Wozniak A, Dobosz M. Metrological Feasibilities of CMM Touch Trigger Probes. Part I: 3D Theoretical Model of Probe Pretravel[J]. Measurement, 2003,34(4): 273-286.
[9]Puangmali P, Althoefer K, Seneviratne L D, et al.Computer-aided Measurement Plan for an Impeller on a Coordinate Measurement Machine with a Rotating and Tilting Probe[J]. Robotics and Computer-integrated Manufacturing, 2008, 24(6):788-795.
[10]费致根, 郭俊杰, 罗国富. 一种共聚焦激光测头轴线位置标定方法研究[J]. 燕山大学学报, 2010, 34(3): 266-268.
Fei Zhigen,Guo Junjie,Luo Guofu. Research on Calibration Method of Confocal Laser Probe Axis Position[J].Journal of Yanshan University,2010,34(3):266-268.

[1]	XIE Shenglong1;LI Tiefeng2;WANG Binrui1;CHEN Dijian1. Hysteresis Modeling Method of Pneumatic Muscles Based on KP Model [J]. China Mechanical Engineering, 2020, 31(10): 1183-1189.
[2]	LI Yongquan1,2;WU Pengtao1,2;ZHANG Yang1,2 ;ZHANG Lijie2,3. Dynamics Parameter Identification and Control of a Spherical 2-DOF Redundant Driven Parallel Robot System [J]. China Mechanical Engineering, 2019, 30(16): 1967-1975.
[3]	WEI Wei1,2;GENG Kuihua1,2;GENG Ainong3;WANG Shaowei1;LI Xinmo3. Frictional Force Test of Rotor Compressor Slides-chute Movement Deputy Based on LuGre Mode [J]. China Mechanical Engineering, 2019, 30(08): 932-938.
[4]	CUI Fangyuan;HUA Dengxin;LI Yan;KONG Lingfei;LI Pengyang. A Merged Binding Modeling Method for Contact Fields of Bolted Joints [J]. China Mechanical Engineering, 2018, 29(16): 1912-1920.
[5]	REN Peng;WANG Lihua;WANG Chunfeng. Experimental Study on Normal Dynamic Contact Stiffnesses of Trail Interfaces under Lubrications [J]. China Mechanical Engineering, 2018, 29(07): 811-816.
[6]	QIAN Cheng;HU Hongsheng. Nonlinear Modeling and Parameter Identification of Hysteresis Characteristics on Piezoelectric Actuator Based on LS-SVM [J]. China Mechanical Engineering, 2018, 29(07): 835-841.
[7]	LI Song1,2;YANG Shiyi1,2;ZHANG Fengfeng1,2;SUN Lining1,2. Parameter Identification Method of 6-DOF Radiotherapy Beds Based on Combined Genetic Algorithm and Mini-max Optimization [J]. China Mechanical Engineering, 2018, 29(01): 57-62.
[8]	YAN Hao1;BAI Ruilin1;JI Feng2. An Improved Dynamics Parameter Identification Method for SCARA Robots [J]. China Mechanical Engineering, 2017, 28(22): 2707-2713.
[9]	CHEN Dongning, LIU Yidan, YAO Chengyu, JIANG Donglin, WANG Kexun, . Friction Compensation of Proportional Multiway Valve Based on Modified Viscous Friction LuGre Model [J]. China Mechanical Engineering, 2017, 28(01): 62-68.
[10]	Guo Fei, Li Yongquan, Li Yukun, Zhang Yu, Zhang Lijie, . Identification of Dynamics Parameters for an Electro-hydraulic 3-UPS/S Parallel Stabilized Paltform [J]. China Mechanical Engineering, 2016, 27(21): 2862-2868,2876.
[11]	Zhang Jin, Kong Xiangdong, Yao Jing, Wang Juan, Chang Liying. Modeling and Simulation of ABS HCU [J]. China Mechanical Engineering, 2016, 27(21): 2967-2974.
[12]	Yu Qibing, Yin Aijun, Xue Lei, Zhang Quan. Analysis of Structure Vibration Based on Out-of-plane Monocular Vision [J]. China Mechanical Engineering, 2016, 27(17): 2367-2371,2378.
[13]	Chen Hongyue, Bai Yangxi, Zhang Yu, Deng Wenhao. Model Identification and Parameter Forecasting of Rubber Conveyor Belt Restoring Force [J]. China Mechanical Engineering, 2016, 27(06): 810-814.
[14]	Wang Zhonghou, Yuan Keke, Li Gang. Optimization Identification for Dynamic Characteristic Parameters of Sliding Joints Based on Response Surface Methodology [J]. China Mechanical Engineering, 2016, 27(05): 622-626.
[15]	Wu Lulu, Han Jiang, Tian Xiaoqing, Xia Lian. Parameter Identification of Servo Control System Based on Unbiased Least Square Method [J]. China Mechanical Engineering, 2016, 27(01): 109-113.

Identification Approach of Geometrical Parameters for Non-contact Five-coordinate Measuring Machine

非接触式五坐标测量机系统几何参数的辨识方法

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics