Research on Micro EDM Pulse Generator with Fuzzy Control

China Mechanical Engineering ›› 2012, Vol. 23 ›› Issue (14): 1718-1722.

Previous Articles Next Articles

Research on Micro EDM Pulse Generator with Fuzzy Control

Huang Ruining1,2;Liu Bing1;Lou Yunjiang1

1.Harbin Institute of Technology Shenzhen Graduate School,Shenzhen,Guangdong,518055
2.Key Laboratory of Mechanical Equipment Manufacturing and Control Technology Guangdong University of Technology,Ministry of Education,Guangzhou,510006

Online:2012-07-25 Published:2012-07-30
Supported by:

National Natural Science Foundation of China（No. 51105110）;

Research Fund for the Doctoral Program of Higher Education of China（No. 20112302120075）;
National High-tech R&D Program of China (863 Program) （No. 2011AA04A103）

基于模糊控制的微细电火花加工脉冲电源研究

黄瑞宁1,2;刘兵1;楼云江1

1.哈尔滨工业大学深圳研究生院，深圳，518055
2.广东工业大学机械装备制造与控制技术教育部重点实验室，广州，510006

基金资助:
国家自然科学基金资助项目(51105110)；哈尔滨工业大学创新基金资助项目(HIT.NSFIR.2010125)；高等学校博士学科点专项科研基金资助项目(20112302120075)；国家高技术研究发展计划(863计划)资助项目(2011AA04A103)
National Natural Science Foundation of China（No. 51105110）;

Research Fund for the Doctoral Program of Higher Education of China（No. 20112302120075）;
National High-tech R&D Program of China (863 Program) （No. 2011AA04A103）

Abstract

Abstract:

A micro EDM pulse generator was presented herein. It adopted effective discharge spark number detection method to detect the discharge state. In addition, it utilized fuzzy control to adjust the pulse-on time and pulse-off time to improve the machining performance. Experimental results show that the pulse generator will improve the machining accuracy and machining efficiency effectively on the basis of stability.

Key words: pulse generator, micro-EDM, discharge state detection, fuzzy control

摘要：

设计了一套微细电火花加工脉冲电源，该电源采用有效放电火花数检测方法对放电状态进行统计，并利用模糊控制算法对脉冲宽度和脉冲间隔进行调整以改善加工性能。试验结果表明，该脉冲电源在保证加工稳定性的基础上，能够有效地提高加工精度及加工效率。


关键词: 脉冲电源, 微细电火花加工, 放电状态检测, 模糊控制

CLC Number:

TG661

HUANG Rui-Ning-1, 2, LIU Bing-1, LOU Yun-Jiang-1. Research on Micro EDM Pulse Generator with Fuzzy Control[J]. China Mechanical Engineering, 2012, 23(14): 1718-1722.

黄瑞宁1, 2, 刘兵1, 楼云江1. 基于模糊控制的微细电火花加工脉冲电源研究[J]. 中国机械工程, 2012, 23(14): 1718-1722.

[1]	LIU Yanyu;YU Fan;SONG Juanjuan;PANG Jisu;KAKU Chuyo. Detection of Brake Requests Using Neural Network and Fuzzy Control [J]. China Mechanical Engineering, 2020, 31(23): 2847-2855.
[2]	LI Xiaopeng, WANG Yuangang, LIU Yu, WANG Hui, ZHAO Fuling. Experimental Study on Effects of Debris on Electrode Shape Wear in Micro-EDM [J]. China Mechanical Engineering, 2020, 31(15): 1815-1822,1889.
[3]	WANG Feng;ZHANG Yongbin;LIU Guangmin;WANG Qing;YUAN Weiran;HU Bo. Discharge Erosion of VHF Resonant Micro EDM Pulse Generators [J]. China Mechanical Engineering, 2019, 30(20): 2439-2446.
[4]	WANG Xuanyao1,2,3;CHENG Yi1;CHENG Yu1;YE Youdong1,2. Lane Keeping Model Prediction Control and Vehicle Stability Control on Low Adhesion Coefficient Roads [J]. China Mechanical Engineering, 2019, 30(09): 1018-1025.
[5]	ZHOU Yuwei;ZHANG Qing;SHI Yunfei. Simulation and Verification of Hydraulic Control Systems for Continuous Lifting [J]. China Mechanical Engineering, 2018, 29(16): 1936-1942.
[6]	YANG Shen1;OU Jian1;YANG Echuan2;HU Jingqing1;ZHANG Yong1. Research on Electric Vehicle Yaw Stability Based on Torque Optimum Distributions [J]. China Mechanical Engineering, 2017, 28(14): 1664-1668.
[7]	WANG Jiande, ZHOU Yunshan, YANG Huiyong, JIA Jiefeng, LI Quan. Research on Dynamic Mode Transition of Hybrid Electric Vehicle Based on Continuously Variable Transmission(CVT) [J]. China Mechanical Engineering, 2017, 28(10): 1253-236.
[8]	Liu Ruijia, Chen Kai. Research on Fuzzy Adjacent Coupling Synchronization Control in Multi-cylinder Leveling System [J]. China Mechanical Engineering, 2016, 27(17): 2316-2321.
[9]	Kou Farong, Fan Yangqiang, Zhang Chuanwei, Du Jiafeng, Wang Zhe. Time Delay Compensation Control of Semi-active Suspension with Vehicle Electro-hydrostatic Actuator [J]. China Mechanical Engineering, 2016, 27(15): 2111-2117.
[10]	Zhang Haifeng, Wang Lifeng, Liu Jianyong. Experimental Study of EDM Pulse Generator for Small Hole Machining [J]. China Mechanical Engineering, 2016, 27(13): 1735-1739,1789.
[11]	Hu Yong, Ji Huanyu, Wang Gongxian. Experimental Investigation on Characteristics of a Novel Hydraulic Shock Pulse Generator [J]. China Mechanical Engineering, 2016, 27(12): 1638-1642.
[12]	Xie Miao, Liu Zhixiang, Chi Cheng, Mao Jun. Electro-hydraulic Servo Position and Pressure Hybrid Control Method of Forepoling System on Tunnelling [J]. China Mechanical Engineering, 2016, 27(02): 239-245.
[13]	Zhang Chunhui, Zhao Jingyi, Rong Xiaoyu, Bu Dan, . Research on Multi-stage Cylinder Lifting System Based on Subsection Control [J]. China Mechanical Engineering, 2015, 26(3): 319-323.
[14]	Zhang Li, Chen Shizhen, Xu Juan, Niu Qingbo. Variable Step Size Optimizing Method of Rotor Dynamic Balance Based on Fuzzy Control [J]. China Mechanical Engineering, 2015, 26(23): 3167-3171.
[15]	Gao Aiyun, Deng Xiaozhong, Zhang Mingzhu, Fu Zhumu. Regenerative Braking Control Strategy for PHEV Based on Optimal Braking Effect [J]. China Mechanical Engineering, 2015, 26(15): 2118-2124.

Research on Micro EDM Pulse Generator with Fuzzy Control

基于模糊控制的微细电火花加工脉冲电源研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics