State-of-the-art of Machining Dust Researches and Their Framework 

Abstract

Abstract:

A study of environmental impacts in widely-used machining is important in green manufacturing research.The studies about the machining

dust were reviewed herein.Firstly,the attributes like chemical composition,particle size,particle size distribution and concentration, and the harms of machining dust were introduced.Then the formation mechanism,influence factors and their effects and controlling

methods were summarized.Finally,based on the above analyses,the framework and the trends of research on machining dust were proposed.

Key words:

green manufacturing, machining dust, framework, research summary

摘要：

对机械加工过程中环境影响问题的研究是绿色制造研究的重要组成部分。对量大面广的机械加工产生的粉尘问题的研究现状进行了综述。首先介绍了现有研究中关注最多的机械加工粉尘的化学成分、粉尘粒径、粒径分布和浓度等属性及其多种危害;随后以小粒径粉尘颗粒为研究重点,分析了机械加工粉尘的产生机理、影响因素及其规律、控制方法等;最后建立了机械加工粉尘问题研究的体系框架，并指出机械加工粉尘问题研究的发展趋势。

关键词:

绿色制造, 机械加工粉尘, 体系结构, 综述

CLC Number:

TH186

LIN Fan, LIU Fei, LI Cong-Bei, ZHANG Wen-Yuan.

State-of-the-art of Machining Dust Researches and Their Framework 

[J]. China Mechanical Engineering, 2011, 22(8): 994-1001.

任凡, 刘飞, 李聪波, 张文元.

机械加工粉尘问题的研究现状及体系结构框架

[J]. 中国机械工程, 2011, 22(8): 994-1001.

References

[1]任凡[1],刘飞[1].切削过程中悬浮粉尘颗粒的空间分布特性研究[J].中国机械工程,2010(15):1849-1854.
[2]张忠强[1].以车代磨工艺的研究与应用[J].漳州师范学院学报：自然科学版,2009,22(2):59-62.
[3]付昊[1],周莉[1],王成勇[1].石墨电极机械加工的粉尘防治[J].模具制造,2006(5):64-68.
[4]吴冉[1].数控机床常见故障的诊断与维修[J].现代制造工程,2004(7):30-31.
[5]刘祖明[1],黎前虎[1].镁合金零件的机械加工与安全[J].汽车工艺与材料,2004(5):36-38.
[6]党君祥,钟圣俊,李刚,孙莉,邓煦帆.铣销镁粉爆炸危险性及防爆措施[J].中国粉体技术,2002,8(6):16-18.
[7]刘飞,曹华军,张华等.绿色制造的理论与技术[M]科学出版社,2005.
[8]Riad Khettabi,Victor Songmene,Jacques Masounave.Effects of Speeds, Materials, and Tool Rake Angles on Metallic Particle Emission During Orthogonal Cutting[J]. Journal of Materials Engineering and Performance . 2010 (6)
[9]Imed Zaghbani,Victor Songmene,Riad Khettabi.Fine and Ultrafine Particle Characterization and Modeling in High-Speed Milling of 6061-T6 Aluminum Alloy[J]. Journal of Materials Engineering and Performance . 2009 (1)
[10]Lu F C,Kacew S.Basic Toxicology. . 2002
[11]Zimmer A T,Maynard A D.Investigation of theAerosol Produced by a High-speed Hand-heldGrinder Using Various Substrates. Annals ofOccupational Hygiene . 2002
[12]Khettabi R,Songmene V,Zaghbani I.Modeling ofParticle Emission during Dry Orthogonal Cutting. Journal of Materials Engineering and Perform-ance . 2008
[13]Hoower M D,Finch G L,Mewhinney J A,et al.Release of Aerosols during Sawing and Milling ofBeryllium Metal and Beryllium Alloys. AppliedOccupational and Environmental Hygiene . 1990
[14]Julio Rivera L,Michalek D J,Sutherland J W.TheOrigin,Potential Health Effects,and Environmen-tally Conscious Control of Airborne Particulate inManufacturing Operations. http://74.125.155.132/scholarq=cache:7PKhqpBoAFgJ:scholar.google.com/+Environ-mentally+Conscious+Control+of+Airborne+Particulate+in+Manufacturing+Operations&hl=zh-CN&as_sdt=2000&as_vis=1 . 2010
[15]WILLIAM S,,OMAR S,SAID E S.Application of aluminum-beryllium composite for structural aerospace component. Engineering Failure Analysis . 2004
[16]Martyny J W,Hoover M D,Mroz M M,et al.Aerosols Generated during Beryllium Machining. Journal of Occupational and Environmental Medicine . 2000
[17]Khettabi R,Songmene V.Understanding the For-mation of Nano and Micro Particles during Metal Cutting. International Journal of Signal System Control and Engineering . 2008
[18]V Songmene,B Balout,J Masounave.Clean Machining: Experimental Investigation on Dust Formation—Part I: Influence of Machining Parameters and Chip Formation. Int. J. Environ. Conscious Des. Manuf. (ECDM) . 2008
[19]V Songmene,B Balout,J Masounave.Clean Machining: Experimental Investigation on Particle Formation, Part II: Influence of Machining Strategies and Drill Condition. Int. J. Environ. Conscious Des. Manuf. (ECDM) . 2008
[20]R Khettabi,V Songmene,J Masounave.Effect of Tool Lead Angle and Chip Formation Mode on Particle Emission in Dry Cutting. Journal of Materials Processing Technology . 2007
[21]Yoshida,T,Shima,S,Nagaoka,K,Taniwaki,H,Wada,A,Kurita,H,Morita,K.A study on the beryllium lymphocyte transformation test and the beryllium levels in working environment. Industrial Health . 1997
[22]Kulur V N,King N C.An experimental investigation ofair quality in wet dry turning. Annals of the CIRP . 2000
[23]Balout B,Songmene V,Masounave J.An Experi-mental Study of Dust Generation during Dry Drill-ing of Pre-cooled and Pre-heated Workpiece Ma-terials. Journal of Manufacturing Processes . 2007
[24]Brown DM,Wilson MR,MacNee W,et al.Size-dependent proinflammatory effects of ultrafine polystyrene particles: a role for surface area and oxidative stress in the enhanced activity of ultrafines. Toxicology and Applied Pharmacology . 2001
[25]Donaldson K,Li X Y,MacNee W.Ultrafine (nanometer) particle mediated lung injury. Journal of Aerosol Science . 1998
[26]Arumugam P U,Malshe A P,Batzer S A,et al.Study of Airborne Dust Emission and Process Per-formance during Dry Machining of Aluminum-Sili-con Alloy with PCD and CVD Diamond-coated Tools. Journal of Manufacturing Processes . 2003