Analysis of Action Mechanism of Influencing Factors of Roll Forming Force

doi:10.3969/j.issn.1004-132X.2023.08.014

Abstract

Abstract: In order to study the influencing factors of forming forces， a roll forming simulation model with 6 stands was established according to the constant radius forming method. Through experiments， the forming forces of different sheets were measured in each stand， and the hardness of the same position at the corner after deformation of the same sheet was measured. The effects of flange width， work-hardening， and sheet thickness on forming force were analyzed. The results show that the forming force increases unobvious with the increase of board width； the forming force is approximately proportional to the square of sheet thickness； forming force and hardness at the corner show the same changing law.

Key words: , roll forming, forming force, constant radius forming process, work-hardening

摘要： 为研究成形力影响因素，根据定半径成形法建立了6道次辊弯成形的仿真模型。通过实验测量了不同板材每道次的成形力和同一板材变形后弯角区相同位置的硬度，分析了立边长度、加工硬化、板厚对成形力的影响。结果表明，成形力随板宽的增加有不显著的增大趋势；成形力与板厚的平方近似成正比；成形力与弯角区硬度呈现相同的变化规律。

关键词: 辊弯成形, 成形力, 定半径成形法, 加工硬化

CLC Number:

TH16

HAN Fei, LI Chong. Analysis of Action Mechanism of Influencing Factors of Roll Forming Force[J]. China Mechanical Engineering, 2023, 34(08): 993-999,1006.

韩飞, 李冲. 辊弯成形力影响因素作用的机理分析[J]. 中国机械工程, 2023, 34(08): 993-999,1006.

References

［1］韩飞，李荣健. 超高强钢多道次辊弯成形回弹规律研究［J］. 机械工程学报， 2019， 55（2）：73-81.
HAN Fei， LI Rongjian. Springback Law of Ultra High Strength Steel in Multiple Stands Roll Forming Process ［J］. Journal of Mechanical Engineering， 2019， 55（2）：73-81.
［2］韩飞，朱德鹏. 辊弯成形中成形力的理论分析和有限元仿真［J］. 锻压技术， 2016， 41（12）：150-155.
HAN Fei， ZHU Depeng. Theoretical Analysis and Numerical Simulation on Forming Force in Rolling［J］. Forging & Samping Technology， 2016， 41（12）：150-155.
［3］杨世军. 典型截面辊弯成型变形区及力能参数研究［D］. 北京：北方工业大学， 2012.
YANG Shijun. Deformation and Energy Paramcters Research of Typical Cross-section of Roll Forming. Beijing：North China University of Techuology，2012.
［4］BECKER M， GROCHE P. Towards Nonstop Availability in Roll Forming through Digitalization ［M］∥Production at the Leading Edge of Technology. Berlin：Springer， 2019：219-228.
［5］DE ARGANDOA E S， MENDIGUREN J， GALDOS L. Numerical Prediction of Force and Energy Consumption in Roll Forming Processes［C］∥Proceedings of the 22nd International ESAFORM Conference on Material Forming：ESAFORM 2019. Vitoria-Gasteiz， 2019：170006.
［6］GROCHE P， MUELLER C， TRAUB T， et al. Experimental and Numerical Determination of Roll Forming Loads［J］. Steel Research International， 2014， 85（1）：112-122.
［7］GROCHE P， MUELLER C， BAEUMER L. Verification of Numerical Roll Forming Loads with the Aid of Measurement Equipment［J］. Advanced Materials Research， 2014， 939：373-380.
［8］MUELLER C， XUN G， BA E L， et al. Influence of Friction on the Loads in a Roll Forming Simulation with Compliant Rolls［J］. Key Engineering Materials， 2014， 3193（611/612）：436-443.
［9］GALDOS L， ULIBARRI U， GIL I， et al. Friction Coefficient Identification in Roll Forming Processes［J］. Key Engineering Materials， 2014， 3193（611/612）：425-435.
［10］ABEYRATHNA B， ROLFE B， HODGSON P， et al. Sensitivity Analysis of Forming Force， Torque and Material Properties in the Roll Forming Process［J］. AIP Conference Proceedings. 2013，1567：900-903
［11］ABEYRATHNA B， ROLFE B， HODGSON P， et al. A First Step towards a Simple In-line Shape Compensation Routine for the Roll Forming of High Strength Steel［J］. International Journal of Material Forming， 2016， 9（3）：423-434.
［12］ABEYRATHNA B， ROLFE B， WEISS M. A First Step towards an In-line Shape Compensation for UHSS Roll Forming［J］. IOP Conference Series：Materials Science and Engineering， 2019， 651（1）：012063.
［13］TRAUB T， GNGR B， GROCHE P. Measures towards Roll Forming at the Physical Limit of Energy Consumption［J］. The International Journal of Advanced Manufacturing Technology， 2019， 104（5/8）：2233-2245.
［14］JURKOVIC＇ M， JURKOVIC＇ Z， OBAD M， et al. An Investigation of the Force and Torque at Profile Sheet Metal Rolling-input Data for the Production System Reengineering［J］. Tehnicˇki Vjesnik， 2015， 22（4）：1029-1034.
［15］韩飞，牛丽丽，王允，等. 超高强钢辊弯成形回弹机理分析及控制研究［J］. 机械工程学报， 2018， 54（2）：131-137.
HAN Fei， NIU Lili， WANG Yun， et al. Research on Springback Mechanism and Control of Ultra High Strength Steel in Roll Forming Process［J］. Journal of Mechanical Engineering， 2018， 54（2）：131-137.
［16］吴芳堤，曹晶晶. 金属材料洛氏硬度与抗拉强度的相关关系［J］. 理化检验（物理分册）， 2019， 55（5）：301-304.
WU Fangdi， CAO Jingjing. Relationship between Rockwell Hardness and Tensile Strength of Metal Materials［J］. PTCA（PARTA：Phys. Test. ）， 2019， 55（5）：301-304.
［17］邹宗园，韩舒婷，王宏中，等. 考虑循环软化的箱型承载结构安定性分析［J］. 机械工程学报， 2021， 57（2）：62-69.
ZOU Zongyuan， HAN Shuting， WANG Hongzhong， et al. Shakedown Analysis of Box Bearing Structure by Considering Cyclic Softening Effect［J］. Journal of Mechanical Engineering， 2021， 57（2）：62-69.

[1]	JIA Zhixin, ZHANG Kaiyue, WANG Jin. Study on EDM of PCD by Mixing Iron Powders [J]. China Mechanical Engineering, 2023, 34(22): 2684-2692.
[2]	MIN Delei, TONG Ruting, WEI Yintao. Yaw Rate Calculation and Vehicle Stability Control Considering Tire Nonlinearity [J]. China Mechanical Engineering, 2023, 34(21): 2521-2530.
[3]	YANG Zhonghao, JIANG Bingyan, MA Zhigao, YANG Di, ZHANG Lu, . Adjustment of Thickness Uniformity for Precision Electroformed Mold Insert [J]. China Mechanical Engineering, 2023, 34(21): 2531-2539.
[4]	XU Jilong, LIU Fucai, NIU Yunzhan. Design and Analysis of a Novel Weak-coupling Parallel Hip Exoskeleton with Large Angle of Rotation [J]. China Mechanical Engineering, 2023, 34(21): 2540-2547.
[5]	REN Yongsheng, YAO Donghui, ZHANG Jinfeng. Research Advances in Chatter of Metal Cutting Systems Involving Time Delays [J]. China Mechanical Engineering, 2023, 34(21): 2548-2567,2576.
[6]	CHEN Qinghua, LYU Ke, WANG Dejun, WANG Jiangang, WANG Jianye, FENG Peng. Performance of Functional Gradient Explosion-proof Structures of Experimental Cabin under Explosive Loading [J]. China Mechanical Engineering, 2023, 34(21): 2568-2576.
[7]	ZHU Zongming, JI Suqiang, WANG Hao, TANG Puhua, LIANG Liang. Hemodynamics Analysis of Interventional Robots in Diagnosis and Treatment Based on Fluid-structure Interaction [J]. China Mechanical Engineering, 2023, 34(21): 2592-2599.
[8]	XU Wan, CHENG Zhao, XIA Ruidong, CHEN Hancheng. An Adaptive Robust Unscented Kalman Filter Localization Algorithm Based on Dynamic Residual [J]. China Mechanical Engineering, 2023, 34(21): 2607-2614.
[9]	LIU Jie, JIAN Linjie, DOU Zecheng, WEN Guilin, WANG Ruikun, LI Fangyi. On Sound Absorption Characteristics of Lightweight Structures Constructed by UMPPs [J]. China Mechanical Engineering, 2023, 34(20): 2395-2402.
[10]	ZHU Jiangfeng, CAO Yuguang, ZHAO Qiankun, LI Lei. Study on Hydrodynamic Stability of a Dot Matrix Offshore Wind Turbine Foundation Structure [J]. China Mechanical Engineering, 2023, 34(20): 2428-2433，2474.
[11]	LU Yaoan, QIU Hongjian, WANG Chengyong, . Smooth Tool Orientation Generation Method of Five-axis Ball-end Milling via RTOs Interpolation [J]. China Mechanical Engineering, 2023, 34(20): 2466-2474.
[12]	QU Xiaozhang, ZHANG Jiabei, ZHAI Fangzhi. Sensitivity Analysis and Optimization of High Speed Train Cooling Centrifugal Fan Performance [J]. China Mechanical Engineering, 2023, 34(20): 2504-2512.
[13]	XU Meijiao, XUE Shanliang, ZHANG Hui, ZHOU Guoqing, LU Honggen. Manufacturing Readiness Level Assessment Method of Complex Product Assembly Based on BP-AdaBoost Algorithm [J]. China Mechanical Engineering, 2023, 34(20): 2513-2519.
[14]	XIE Zhong, WEN Donghui, CHENG Zhichao, KONG Fanzhi. Derivation Mechanism of Cyclic Alternating Dynamic Pressures in Linear Hydrodynamic Polishing Flow Fields [J]. China Mechanical Engineering, 2023, 34(19): 2288-2295.
[15]	YANG Jisen, ZHOU Run, ZHANG Tianheng, LU Yu, WU Zhuo, ZHANG Di, ZHANG Jing. Research on Magnetic Field Compensated Double-layer Time-grating Angular Displacement Sensors under Structural Parameter Constraints [J]. China Mechanical Engineering, 2023, 34(19): 2296-2303，2312.