Sintering and Mechanics Properties of C3N4 Based Ceramic Tool Materials

doi:10.3969/j.issn.1004-132X.2023.03.012

Abstract

Abstract: A new type of composite ceramic tool material was developed with C3N4 as matrix, Ti(C, N) as additive phase and Mo, Ni, Co as metal phase. By hot press sintering, C3N4 based ceramic tool materials were sintered. The fracture toughness, flexural strength and vickers hardness of the composites were measured and the microstructure was analyzed. The results show that the C3N4 based ceramic tool material containing 35% Ti(C, N) and 8% Ni-Co, which was sintered under the sintering temperature of 1600 ℃, duration time of 45 min and sintering pressure of 32 MPa, have the optimum mechanics properties. The appropriate content of Ti(C, N) may refine crystal grains of C3N4, increase sintering density, and improve mechanics properties. The microstructure may be fine and uniform with appropriate Ni-Co contents.

Key words: C3N4 based ceramic tool material, mechanics property, microstructure, component content, sintering process

摘要： 采用热压烧结工艺，以Ti(C, N)为添加相，以Mo、Ni和Co为金属相，成功制备了氮化碳(C3N4)基陶瓷刀具材料，测量了其断裂韧度、抗弯强度和维氏硬度，分析了其微观组织。结果表明，在烧结温度为1600 ℃、保温时间为45 min和烧结压力为32 MPa的工艺条件下，Ti(C, N)质量分数为35%、Ni-Co质量分数为8%的C3N4基陶瓷刀具材料力学性能最优。合适的Ti(C, N)含量能细化C3N4晶粒、提高烧结密度、改善力学性能，合适的Ni-Co含量能使微观组织细小均匀。

关键词: C3N4基陶瓷刀具材料, 力学性能, 微观组织, 组分含量, 烧结工艺

CLC Number:

TG711

ZHANG Yan, HUANG Chuanzhen, LIU Hanlian. Sintering and Mechanics Properties of C3N4 Based Ceramic Tool Materials[J]. China Mechanical Engineering, 2023, 34(03): 352-358，368.

张岩, 黄传真, 刘含莲. 氮化碳基陶瓷刀具材料的制备与力学性能研究[J]. 中国机械工程, 2023, 34(03): 352-358，368.

References

［1］LIU A Y, COHEN M L. Prediction of New Low Compressibility Solid［J］. Science,1989, 245:841-842.
［2］LIU A Y, COHEN M L. Structural Properties and Electronic Structure of Low Compressibility Materials:β-Si3N4 and Hypothetical β-C3N4［J］. Physical Review B,1990, 41(15):10727-10734.
［3］CHAMPI A,LACERDA R G, MARQUES F C. Thermal Expansion Coefficient of Amorphous Carbon Nitride Thin Films Deposited by Glow Discharge［J］. Thin Solid Films, 2002, 420/421:200-204.
［4］KHURSHUDOV A G, KATO K. Tribological Properties of Carbon Nitride Overcoat for Thin-film Magnetic Rigid Disks［J］. Surface and Coatings Technology,1996, 86/87:664-671.
［5］FERNANDEZ A,FERNANDEZ-RAMOS C, SANCHEZ-LOPEZ J C. Preparation, Microstructural Characterisation and Tribological Behaviour of CNx Coatings［J］. Surface and Coatings Technology, 2003, 163/164:527-534.
［6］EGERHAZI L, GERETOVSZKY Z, SZORENYI T.Carbon Nitride Films of Uniform Thickness by Inverse PLD［J］. Applied Surface Science, 2007, 253:8197-8200.
［7］KAWAGUCHI M, YAGI S,ENOMOTO H. Chemical Preparation and Characterization of Nitrogen-rich Carbon Nitride Powders［J］. Carbon, 2004, 42:345-350.
［8］MARTIN-GIL J, MARTIN-GIL F J, MORAN E, et al. Synthesis of Low Density and High Hardness Carbon Species Containing Nitrogen and Oxygen［J］. Acta Metall. Mater., 1995, 43(3):1243-1247.
［9］LEE D H, LEE H, PARK B. Hardness and Modulus Properties in Ion-beam-modified Amorphous Carbon:Temperature and Dose Rate Dependences［J］. Journal of Materials Research, 1997, 12(8):2057-2063.
［10］RONNING C, FELDERMANN H, MERK R, et al. Carbon Nitride Deposited Using Energetic Species:a Review on XPS Studies［J］. Physical Review B, 1998, 58(4):2207-2215.
［11］MONCLUS M A, CAMERON D C, CHOWDHURY A K M S. Electrical Properties of Reactively Sputtered CNx Films［J］. Thin Solid Films, 1999, 341:94-100.
［12］SAKAMOTO Y, TAKAYA M.Growth of Carbon Nitride Using Microwave Plasma CVD［J］. Thin Solid Film, 2005, 475:198-201.
［13］傅德君. 氮化碳薄膜的制备和性能研究［D］. 武汉:武汉大学, 1999.
FU Dejun. Preparation and Properties of Carbon Nitride Thin Films［D］. Wuhan:Wuhan University, 1999.
［14］吴大维, 何孟兵, 郭怀喜，等. 氮化碳薄膜的结构与性能研究［J］. 物理学报, 1997, 49(3):530-535.
WU Dawei, HE Mengbing, GUO Huaixi, et al. Structure and Properties of Carbon Nitride Thin Films［J］. Acta Physica Sinica, 1997, 49(3):530-535.
［15］吴大维, 曾昭元, 刘传胜，等. 高速钢镀氮化碳超硬涂层及其应用研究［J］. 核技术, 2003(4):279-283.
WU Dawei, ZENG Zhaoyuan, LIU Chuansheng, et al. Study on Carbon Nitride Superhard Coating of High Speed Steel and its Application［J］. Nuclear Technology, 2003(4):279-283.
［16］彭友贵, 黎明锴, 范湘军，等. 氮化碳刀具在硬质面加工中的应用［J］. 中国机械工程, 2000,11(10):116-118.
PENG Yougui, LI Mingkai, FAN Xiangjun, et al. Application of Carbon Nitride Tool in Hard Surface Machining［J］. China Mechanical Engineering, 11(10):116-118.
［17］刘忠和, 于启勋, 林景用. 新型氮化碳超硬涂层刀具的切削试验研究［J］. 新技术新工艺, 2003(1):19-20.
LIU Zhonghe, YU Qixun, LIN Jingyong. Study on Cutting Experiment of a New Carbon Nitride Superhard Coating Tool［J］. New Technology & New Process, 2003(1):19-20.
［18］王道波, 石磊. 氮化碳涂层刀具制备工艺与切削性能研究［J］. 中国城市经济, 2010(5):26.
WANG Daobo, SHI Lei. Preparation Technology and Cutting Performance of Carbon Nitride Coating Tools［J］. China Urban Economy, 2010(5):26.
［19］吴大维, 付德君, 毛先唯，等. C3N4/TiN交替复合膜的微结构研究［J］. 物理学报, 1999(5):904-912.
WU Dawei, FU Dejun, MAO Xianwei, et al. Microstructures of C3N4/TiN Alternating Composite Films［J］. Acta Physica Sinica, 1999(5):904-912.
［20］李荣久. 陶瓷-金属复合材料［M］. 2版.北京:冶金工业出版社, 2004:86, 269-275.
LI Rongjiu. Ceramic-Metal Composite Materials［M］. 2nd ed. Beijing:Metallurgical Industry Press, 2004:86, 209-275.
［21］黄培云. 粉末冶金原理［M］. 2版.北京:冶金工业出版社, 2001:307-311.
HUANG Peiyun. Principles of Powder Metallurgy［M］. 2nd ed. Beijing:Metallurgical Industry Press, 2001:207-311.
［22］王国栋. 硬质合金生产原理［M］. 北京:冶金工业出版社, 1988:386-389.
WANG Guodong. Production Principle of Cemented Carbide［M］. Beijing:Metallurgical Industry Press, 1988:286-389.
［23］果世驹. 粉末烧结理论［M］. 北京:冶金工业出版社, 1998:301-324.
GUO Shiju. Theory of Powder Sintering［M］. Beijing:Metallurgical Industry Press, 1998:301-384.

[1]	FANG Xuewei, JIANG Xiao, WANG Zhe, WU Xiaokang, HUANG Ke. Forming Process Optimization of Wire and Arc Additive Manufactured High-strength Steel ER120S-G [J]. China Mechanical Engineering, 2023, 34(02): 218-225.
[2]	JIANG Chuangyu, ZHANG Baoqiang, CHEN Yun, WANG Cunfu, LUO Huageng, HU Jiexiang, CAO Longchao. Study on Mechanics Properties and Numerical Convergence of Gyroid Cellular Structures [J]. China Mechanical Engineering, 2022, 33(23): 2790-28000.
[3]	JIAO Chen, CHAO Long, ZHU Lei, SHEN Lida, LIANG Huixin, DAI Ning, WANG Changjiang, SUN Jun. Design and Manufacture Method of Bionic Porous Structures for Orthopedic Implants [J]. China Mechanical Engineering, 2022, 33(23): 2844-2850.
[4]	TANG Yongfeng, LU Ping, LIU Bin, JIANG Kaiyong, YAN Binggong, LIU Jiawei, HAN Wei, . Design and Mechanics Property Analysis for Different Graded Irregular Porous Structures [J]. China Mechanical Engineering, 2022, 33(23): 2859-2866.
[5]	ZHANG Shuai, CHEN Zhaoqiang, XIAO Guangchun, YI Mingdong, ZHANG Jingjie, ZHOU Tingting, XU Chonghai. Study on Crack Repair Performance of Si3N4/TiC/ZrSi2 Ceramic Tool Materials [J]. China Mechanical Engineering, 2022, 33(19): 2288-2297.
[6]	ZENG Shoujin, LI Chuansheng, LIU Guang, XU Mingsan, LI Dichen. Study on Mechanics Properties and Energy Absorption of Gradient Porous Scaffolds Fabricated by SLM [J]. China Mechanical Engineering, 2022, 33(19): 2364-2371.
[7]	XU Yameng, ZHOU Hai, ZHANG Jiequn, REN Xiangpu, ZHANG Chunwei. Experimental Study of Micro Scale Mechanics Behavior of Cleavable Gallium Oxide Crystals [J]. China Mechanical Engineering, 2022, 33(18): 2234-2240.
[8]	ZHOU Jiali, CHENG Yanhai, CHEN Yongxiong, LIANG Xiubing, BAI Chengjie, DU Wang. Effects of Laser Cladding Process Parameters on Microstructure and Residual Stresses of Fe-based Double Layer Coatings [J]. China Mechanical Engineering, 2022, 33(12): 1418-1426，1434.
[9]	ZHONG Yang, QIN Xiaobo, ZHENG Zhizhen, LI Jianjun, WANG Cheng. Study on Microstructure and Mechanics Properties of 2.25Cr-1Mo-0.25V Steel Fabricated by CMT Wire ARC Additive Manufacturing for Petrochemical Vessels [J]. China Mechanical Engineering, 2022, 33(10): 1251-1259.
[10]	YAO Fangping, LI Xiangmeng, SHI Qiangshengjie, ZHANG Xiao. Research on Preparation and Performance of Graphene-Polymer Flexible Capacitance Sensors [J]. China Mechanical Engineering, 2021, 32(24): 2909-2914.
[11]	ZHENG Yu, GUO Ce, MA Yaopeng, GUAN Jigang. Design，Fabrication and Mechanics Property Analysis of Bionic Multilayer Flexible Lightweight Structures [J]. China Mechanical Engineering, 2021, 32(23): 2876-2882.
[12]	PAN Chengyi, TONG Yuanqi, CAO Guanqun, ZHAO Yanling. Research on Friction and Wear Characteristics and Simulation of Microstructures Surface Unfolding Wheels [J]. China Mechanical Engineering, 2021, 32(22): 2689-2696.
[13]	SHEN Hongzhuo, LIU Yuanming, LIU Yanxiao, WANG Tao, LIU Yanping, . Simulation of Corrugated Rolling of Mg/Al Composite Plates and Analysis of Microstructure Evolution in Deformation Zone [J]. China Mechanical Engineering, 2021, 32(22): 2731-2738.
[14]	ZHANG Heng, DING Xiaohong, SHEN Lei, XU Shipeng. Topology Optimization of Sandwich Damping Composite Structure with Connective Constraint [J]. China Mechanical Engineering, 2021, 32(20): 2403-2410.
[15]	KE Qingdi, JIANG Feng, ZHANG Peng, TIAN Changjun, QIN Xiaozhou. Surface Contamination State Evaluation for Remanufacturing Cores Based on Influence Laws of Restoring Coating Mechanics Properties [J]. China Mechanical Engineering, 2021, 32(19): 2340-2347,2356.