圆锥形件拉深成形应力应变的直接积分解法

摘要/Abstract

摘要：

针对圆锥形件的拉深成形，在平面应力和比例加载条件下，采用参数方程的方法分析得到了变形区应变的微分方程。可在圆锥形件的凸缘区、凹模圆角区及锥壁区分别根据应变微分方程，代入相应的边界条件，采用直接积分得到应力、应变解，将应用于轴对称平面内的积分解法推广至分析圆锥形件的拉深成形问题。在凸缘区，锥角等于0；在锥壁区，锥角等于一定值；在凹模圆角区，将圆角部分的弧段分成若干个微锥段，每一微锥段都可分别作为一个小的等锥角的锥环处理。采用该方法，不仅可以计算锥形件的拉深成形问题，而且可以计算曲面形状已知的一般轴对称曲面零件的成形问题。用直接积分法替代迭代法求解非线性方程，使求解过程大大简化。
选取厚0.87mm 的ST16板材进行了拉深成形实验，以板坯内层为测量面，测量了凸缘区、凹模圆角区和锥壁区的应变分布，理论计算结果与实验结果一致。

关键词: 板材成形, 圆锥形零件拉深, 平面应力模型, 直接积分解法

Abstract:

Under the conditions of plane stress and proportional loading,differential equations of strain and stress in deformation zone of conical part in deep drawing were obtained by the method of parametric equation. After solving the differential equations under the corresponding boundary conditions in the regions of flange, die corner and conical wall of the conical part the stresses and strains might be obtained respectively in every regions by the direct integral method. The applications of the direct integral method were extended from solving the in-plane axisymmetic sheet metal forming problems to analyze conical part deep drawing process.The conical angles were equal to zero and a certain value in flange region and conical wall respectively. The die arc regions might be divided into several small segments and each of them could be taken as a conical part with constant conical angle. This method was applied to solve conical part deep drawing problems and to analyze the forming problem of axisymmetric curved parts with given profile shape. As the substitute of iteration method, the direct integral method was applied to solve nonlinear equations and the solving process could be simplified greatly.The experiments of conical part deep drawing were carried out by using 0.87mm-thick ST16 sheet and the strain distributions in flange,die arc and conical wall regions were measured.It shows that the analytical solutions by the direct integral method are accordant with experimental results.

Key words: sheet metal forming, conical part in deep drawing, plane stress model, direct integral method

中图分类号:

TG386.1

秦泗吉, 邓超, 杨莉, 孔晓华, 王耀华. 圆锥形件拉深成形应力应变的直接积分解法[J]. 中国机械工程, 2016, 27(02): 251-257.

Qin Siji, Deng Chao, Yang Li, Kong Xiaohua, Wang Yaohua. A Direct Integral Method to Solve Stress and Strain of Conical Parts in Deep Drawing Process[J]. China Mechanical Engineering, 2016, 27(02): 251-257.

参考文献

[1]万敏.圆锥形零件冲压成形极限的研究[D].哈尔滨：哈尔滨工业大学, 1995.
[2]Fazli A,Arezoo B. Prediction of Limiting Drawing Ratio Considering the Effective Parameters of Die Arc Region[J]. J. Mat. Proc. Technol., 2012,212(4):745-751.
[3]任运来，吕亚臣，彭加耕，等.相对厚度对锥形零件拉深成形的影响[J].机械工程学报，2010, 46(8):51-55.
Ren Yunlai,Lü Yachen,Peng Jiageng,et al.Effect of Relative Thickness on Tapered Part Drawing[J].Journal of Mechanical Engineering, 2010, 46(8):51-55.
[4]秦泗吉. 轴对称拉深成形凸缘区应力应变解析求解[J]. 机械工程学报, 2011, 46(24):20-25.
Qin Siji.Analytical Solution of Stress and Strain in Flange Deformation in Axisymmetric Deep Drawing Process[J].Journal of Mechanical Engineering, 2011, 46(24):20-25.
[5]戴春俊.板材胀形过程应变分析的实验-数值混合法[D].哈尔滨：哈尔滨工业大学,2013.
[6]纪莲清，谢欢.内孔翻边时变形区应力应变规律研究[J]. 锻压技术,2007,32(1):20-24.
Ji Lianqing, Xie Huan. Stress and Strain Rule Studies of Deformaction Area of Inside Hole Flange[J].Forging & Stamping Technology, 2007, 32(1):20-24.
[7]赵军.圆锥形件拉深成形智能化的研究[D].哈尔滨：哈尔滨工业大学，1997.
[8]梁炳文,胡世光.板料成形塑性理论[M].北京:机械工业出版社,1987.
[9]Thiruvarudchelvan S,Tan M J.A Note on Fluid-pressure-assisted Deep Drawing Processes[J]. J. Mat. Proc. Technol., 2006, 172(2): 174-181.
[10]Wu Y S, Wang X Y,Xia J C.Multipoint Blank Holderforce Control in Hydroforming of Fuel Tank[J].Chinese Journal of Mechanical Engineering，2006，19(2)：200-204.
[11]李敏华.硬化材料的轴对称平面塑性平面应力问题的研究[M].北京:科学出版社,1960.
[12]Nadai A. Plastic Behavior of Metals in the Strain Hardening Range, Part I[J].J. Appl. Phys.,1937,8(3):205-213.
[13]Millenson M B, Manson S S. Determination of Stresses in Gas-turbine Disks Subjected to Plastic Flow and Creep[R]. New York: NACA, 1948.
[14]刘幺和,胡世光.板料的n、r值对应力应变分布的影响[J].锻压技术, 1982,7(3):11-18.
Liu Yaohe,Hu Shiguang.The effect of n and r on Distributions of Stress and Strain[J]. Forging & Stamping Technology,1982,7(3):11-18.