基于三角级数展开的铣削合力频谱推导及刀具偏心估算

摘要/Abstract

摘要：

基于一元切削力机理模型将立铣刀的切削合力分解为公称力和偏心力，采用周期信号的三角级数展开公称力和偏心力，得到其谐波幅值和相位的表达式。基于以上表达式,推导出偶数齿刀具偏心力的偶数次谐波幅值为0，三齿刀具偏心力的刀齿频率谐波幅值也为0。提出了一种用切削合力的主轴和刀齿频率谐波估算刀具偏心距和偏心角的方法，实验结果表明,采用该方法计算出的偏心值接近实测值。从理论上证明了偶数齿刀具的偏心力不存在偶数次谐波成分，所提出的估算方法只需一套估算式和一次切削实验，且数值计算比较容易。研究结果可用于偶数齿刀具的加工过程偏心和磨损辨识及其偏心量估算。

关键词: 铣刀, 偏心, 铣削力, 频谱

Abstract:

The cutting force was discomposed into nominal and eccentric component forces based on unary cutting force model,the trigonometric series of periodic signals was applied to expand these two component forces，and then the amplitude and phase expressions of their harmonics were obtained. Based on these expressions,it is deduced that the even-harmonics amplitudes of the eccentric force for even-tooth milling cutter are zero,the tooth-frequency amplitude of the eccentric force for 3 teeth milling cutters is zero too, and a new estimation method of eccentric distance and angle for milling cutters was presented, which uses the harmonics of resultant cutting force in spindle and tooth frequencies, the estimated eccentric values are close to that measured in experiments.It testifies in theory that there are no even harmonics in the eccentric component force of even-tooth milling cutters, the presented method needs only one set of equation and one cutting test, and its numerical calculation is rather easy for even-tooth milling cutters. The research fruits can be used to identify eccentricity and wear, and estimate eccentricity in process for even-tooth milling cutters.

Key words: milling cutter, eccentricity, milling force, frequency spectrum

中图分类号:

TH161

刘璨, 吴敬权, 刘焕牢, 谭光宇. 基于三角级数展开的铣削合力频谱推导及刀具偏心估算[J]. 中国机械工程, 2016, 27(02): 246-250,272.

Liu Can, Wu Jingquan, Liu Huanlao, Tan Guangyu. Spectral Derivation of Resultant Milling Force and Eccentric Estimation of Tool Based on Trigonometric Series Expansion[J]. China Mechanical Engineering, 2016, 27(02): 246-250,272.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2016/V27/I02/246

参考文献

[1]Schmitz T L,Couey J,Marsh E,et al.Runout Effects in Milling: Surface Finish, Surface Location Error,and Stability[J].Int. J. Mach. Tools & Manuf., 2007,47(5):841-851.
[2]卞荣, 何宁, 李亮, 等. 微细铣削氧化锆陶瓷铣削力特征分析[J]. 中国机械工程, 2014, 25(23): 3200-3206.
Bian Rong,He Ning,Li Liang,et al.Analysis on Characteristics of Milling Force in Micro-milling of ZrO2 Ceramics[J].China Mechanical Engineering,2014,25(23):3200-3206.
[3]Zhang S,Li J F,Sun J,et al. Tool Wear and Cutting Forces Variation in High-speed End-milling Ti-6Al-4V Alloy[J].International Journal of Advanced Manufacturing Technology,2010,46(1/4): 69-78.
[4]Fu H J,Devor R E,Kapoor S G.A Mechanistic Model for the Prediction of the Force System in Face Milling Operations[J].ASME J.Eng. Ind.,1984,106(1):81-88.
[5]Zheng H Q,Li X P,Wong Y S,et al.Theoretical Modeling and Simulation of Cutting Forces in Face Milling with Cutter Runout[J]. Int. J. Mach.Tools&Manuf.,1999,39(12):2003-2018.
[6]Amarego E J A,Desphande N P.Computerized Predictive Cutting Models for Forces in End Milling Including Eccentricity Effects[J]. Annals of CIRP,1989,38(1):45-49.
[7]Li X P,Li H Z.Theoretical Modeling of Cutting Forces in Helical End Milling with Cutter Runout[J].International Journal of Mechanical Sciences,2004,46(9):1399-1414.
[8]刘璨,吴敬权,李广慧,等.基于单刃铣削力峰值的铣刀偏心辨识[J].机械工程学报, 2013,49(1):185-190.
Liu Can,Wu Jingquan,Li Guanghui,et al.Identification of Mills Eccentricity Based on Peak Force of Single Edge[J].Journal of Mechanical Engineering, 2013,49(1):185-190.
[9]Kline W A,Devor R E.The Effect of Runout on Cutting Geometry and Forces in End Milling[J].Int. J. Mach. Tool Des. & Res., 1983,23(2/3):123-140.
[10]Wang J J J,Zheng C M.Identification of Cutter Offset in End Milling without a Prior Knowledge of Cutting Coefficients[J]. International Journal of Machine Tools & Manufacutre,2003,43(7): 687-697.
[11]Wan M,Zhang W H.Systematic Study on Cutting Force Modeling Methods for Peripheral Milling[J].Int. J. of Mach. Tools & Manuf., 2009, 49(5):424-432.
[12]刘显波, 龙新华, 孟光,等.基于频域多目标优化的铣削力系数及偏心参数识别[J].机械工程学报, 2011,47(7):185-190.
Liu Xianbo,Long Xinhua,Meng Guang,et al.The Identifications of Milling Force Coefficients and Eccentricity Based on Multi-objective Optimization in Frequency-domain[J].Journal of Mechanical Engineering,2011,47(7):185-190.
[13]Liu C,Wu J Q,Li G H,et al.Frequency-spectrum Characteristics of Force in End Milling with Tool Wear and Eccentricity[J].Int. J. Adv. Manuf.Technol.,2013,67(1/4):925-938.

[1]	郝壮壮, 张庆春, 胡云波, 郭宜斌, 王东华, 李玩幽. 齿面摩擦和几何偏心对含变位直齿轮啮合刚度的影响研究[J]. 中国机械工程, 2023, 34(23): 2812-2823.
[2]	卢耀安, 丘洪键, 王成勇, . 基于关键刀轴矢量插值的球头铣刀五轴加工光顺刀轴矢量生成方法[J]. 中国机械工程, 2023, 34(20): 2466-2474.
[3]	陈甜, 张兴武, , 刘金鑫, , 陈雪峰, , 严如强, . 自适应频谱塑形主动控制及舰艇领域应用研究进展[J]. 中国机械工程, 2022, 33(04): 482-495.
[4]	赵国龙, 信连甲, 李亮, 王珉, 郝秀清, 何宁. 高硅铝合金的金刚石涂层刀具铣削损伤机理研究[J]. 中国机械工程, 2022, 33(02): 153-159.
[5]	商鹏, 黄思硕, 刘晓鹏, 杨壮, 刘腾, 张建军. 二维振动辅助微细铣削切削力建模与试验研究[J]. 中国机械工程, 2021, 32(06): 648-657，665.
[6]	李强, 郭辰光, 赵丽娟, 冷岳峰, 岳海涛. 具有晶体学各向异性特征的DD5镍基单晶高温合金铣削力建模[J]. 中国机械工程, 2021, 32(06): 734-740.
[7]	刘涛;张丽芳. 基于改进粒子群优化算法的变截面涡旋盘瞬时铣削力模型参数求解[J]. 中国机械工程, 2020, 31(24): 2943-2949.
[8]	孙涛1;秦录芳1;侯军明2;傅玉灿3. 正偏心正交车铣精加工切削层几何形状研究[J]. 中国机械工程, 2020, 31(24): 2972-2978.
[9]	张勇斌, 严广和, 李建原, 姜晨. 金刚石涂层微铣刀的铣削加工试验[J]. 中国机械工程, 2020, 31(15): 1772-1777.
[10]	王泽刚;王福吉;卢晓红;赵猛;樊俊峰. 考虑左旋切削刃切削连续性的碳纤维增强树脂基复合材料铣削研究[J]. 中国机械工程, 2020, 31(08): 991-996.
[11]	刘厚根;范彩明. ZNR2.4罗茨式机械增压器振动特性试验研究[J]. 中国机械工程, 2020, 31(05): 561-566.
[12]	宋守许;李诺楠;杜毅;刘涛. 抑制永磁同步电机转矩脉动的转子再设计方法[J]. 中国机械工程, 2019, 30(17): 2084-2090,2134.
[13]	倪高明；张海；周磊；王强；王羽中. 成形槽技术在高刚性整体硬质合金立铣刀开发中的应用[J]. 中国机械工程, 2019, 30(13): 1626-1631.
[14]	石文天;韩冬;刘玉德;侯岩军. 超低温微铣削芳纶纤维复合材料表面质量[J]. 中国机械工程, 2019, 30(09): 1056-1064.
[15]	蒙臻1,2;崔智1;倪敬1,2;杨永丰1,2. 砂轮磨切中表面活化剂对超声制备纳米雾化液性能的影响[J]. 中国机械工程, 2019, 30(07): 852-857.