一种新型高炉布料器及其运动和应力分析

中国机械工程 ›› 2015, Vol. 26 ›› Issue (12): 1603-1606.

一种新型高炉布料器及其运动和应力分析

林文强;郭爱波

东北大学,沈阳,110819

出版日期:2015-06-25 发布日期:2015-06-29
基金资助:
国家高技术研究发展计划(863计划)资助项目(2014BAF08B01）
National High-tech R&D Program of China (863 Program) （No. 2014BAF08B01）

A New Blast Furnace Distributor and Analyses of Its Movement and Stress

Lin Wenqiang;Guo Aibo

Northeastern University,Shenyang,110819

Online:2015-06-25 Published:2015-06-29
Supported by:
National High-tech R&D Program of China (863 Program) （No. 2014BAF08B01）

摘要/Abstract

摘要：

针对无料钟炉顶布料器结构复杂、占用空间大的缺点,设计了一种基于空间连杆机构的布料器。对布料器结构进行合理简化并建立数学模型，采用ADAMS进行了特定轨迹下的运动仿真，联合MATLAB进行非线性拟合,求出摆动液压缸的控制方程。所研究的布料器工作环境温度为200~600℃且长期承受循环冲击载荷作用,其最常见的失效形式是疲劳失效。基于有限元分析软件ANSYS对布料器危险零件进行强度计算并对其各节点按Goodman-Smith疲劳极限图进行疲劳评定。分析表明：该布料器最大布料角度为40°,布料相对误差小于0.05%，其结构强度满足无限疲劳寿命要求。

关键词: 布料器；空间连杆机构, ADAMS仿真；有限元分析

Abstract:

A spatial-linkage-based distributor was designed since the complexity and large space occupation of the bell-less top equipment.The authors simplified the fabric construction and developed a mathematical model,the governing equations of rotary cylinder was obtained after the specific trajectory motion simulation using ADAMS as well as the nonlinear fitting with MATLAB.The distributor discussed herein was long subjected to cyclic impact load at 200~600℃,fatigue failure was the most common failure mode.Strength calculations of dangerous parts and fatigue assessments of their nodes were conducted using ANSYS,a software of which was based on finite element analysis.Analysis shows that the largest fabric angle of this distributor is of 40°and the relative error is less than 0.05%,the structural strength can meet the requirements of an infinite fatigue life.

Key words: distributor;spatial , linkage , mechanism;ADMAS , simulation;finite element analysis

中图分类号:

TF572

林文强;郭爱波. 一种新型高炉布料器及其运动和应力分析[J]. 中国机械工程, 2015, 26(12): 1603-1606.

Lin Wenqiang;Guo Aibo. A New Blast Furnace Distributor and Analyses of Its Movement and Stress[J]. China Mechanical Engineering, 2015, 26(12): 1603-1606.

参考文献

[1]王维兴.科学评价中国钢铁工业能耗现状与国内外对标[J].四川冶金,2009,31(4):1-6.
Wang Weixing.Scientific Evaluation of the China's Iron and Steel Industry Energy Situation and Contrast Criterion of Somestic and Abroad[J].Sichuan   Metallurgy,2009,31(4):1-6.
[2]Carretero J A,Podhorodeski R P,Nahon M A.Kinematic Analysis and Optimization of a   New Three Degree-of-Freedom Spatial Parallel Manipulator[J].Journal of Mechanical Design,2000,122(1):17-24.
[3]Voloshin A I,Mikhailov N A,Rudenko N N,et al.Improving the Design of Blast-furnace   Charging Apparatuses[J].Metallurgist,2004,48(7):317-320.
[4]李淑华,姚志绵,汪建新.BT型布料器的改进及在中小高炉上的应用[J].冶金设备,2001(3):38-40.
Li Shuhua,Yao Zhimian,Wang Jianxin.Improvement of BT Type Distributor and Application on Middle or Small BF[J].Metallurgical Equipment,2001(3):38-40.
[5]高峻峰,闫洪波,张玉宝.包钢BG-Ⅲ型布料器的三维设计[J].内蒙古石油化工,2010(23):64-65.
Gao Junfeng,Yan Hongbo,Zhang Yubao.BG-Ⅲ   Distributor's Three-dimensional Design[J].Inner Mongolia Petrochemical Industry,2010(23):64-65.
[6]刘斌奇.HG布料器的研制及开发[J].炼铁,2013,32(2):16-19.
Liu Binqi.Research and Development of HG Charging Distributor[J].Ironmking,2013,32(2):16-19.
[7]张于贤,陈德淑,廖振方,等.空间机构自由度计算[J].重庆大学学报(自然科学版),2003,26(9):53-55.
Zhang Yuxian,Chen Deshu,Liao Zhenfang,et al.Exploration on the Formula of Degree of   Freedom of   Space Mechanism[J].Journal of   Chongqing University,2003,26(9):53-55.
[8]罗佑新,郭惠昕,肖伟跃.机构综合的牛顿优化迭代混沌方法研究[J].机械传动,2005,29(6):11-13.
Luo Youxin,Guo Huixin,Xiao Weiyue.Research on Newton Optimization Iteration Chaos Methods of Mechanism Synthesis[J].Journal   of   Mechanical Transmission,2005,29(6):11-13.
[9]孙伟,秦伟,苗文晓.高炉炉顶布料器传动系统动力学仿真[J].机械,2009,36(12):8-12.
Sun Wei,Qin Wei,Miao Wenxiao.Dynamic Simulation   of Transmission System of Blast Furnace Top Charge Distributor[J].Machine,2009,36(12):8-12.
[10]李强,张玉栋,张丽娟,等.COREX竖炉布料规律的数学模型[J].东北大学学报:自然科学版,2011,32(11):1591-1594.
Li Qiang,Zhang Yudong,Zhang Lijuuan,et al.Mathematical Model of Burden Distribution Law for COREX Shaft[J].Journal of Northeastern University:Natural Science,2011,32(11):1591-1594.
[11]陈修龙,赵永生.并联机床运动仿真与运动学分析的新方法[J].中国机械工程,2006,17(5):467-471.
Chen Xiulong,Zhao Yongsheng.A New Solution for Motion Simulation and Kinematic Analysis of Parallel Machine Tool[J].China Mechanical Engineering,2006,17(5):467-471.