玻璃成形抛光相对线速度基本恒定控制算法研究

中国机械工程 ›› 2013, Vol. 24 ›› Issue (24): 3272-3277.

玻璃成形抛光相对线速度基本恒定控制算法研究

韩俊昭1;任锟1;潘骏1;刘思路2;尤灵敏1;沈琦琦1

1.浙江理工大学浙江省机电产品可靠性技术研究重点实验室,杭州,310018
2.合肥工业大学,合肥,230009

出版日期:2013-12-25 发布日期:2013-12-27
基金资助:
国家自然科学基金资助重点项目(50935002);国家科技支撑计划资助项目（2009BAF39B03)；浙江省重点科技创新团队资助项目(2010R50005);浙江省面上科研工业项目(2009C31096)

Research on Limited Relative Velocity Fluctuation in Glass Shaping Polishing

Han Junzhao1;Ren Kun1;Pan Jun1;Liu Silu2;You Lingmin1;Shen Qiqi1

1.Zhejiang Province's Key Laboratory of Reliability Technology for Mechanical and Electronic Product,Zhejiang Sci-Tech University, Hangzhou,310018
2.Hefei University of Technology,Hefei,230009

Online:2013-12-25 Published:2013-12-27
Supported by:
National Natural Science Foundation of China（No. 50935002）;The National Key Technology R&D Program（No. 2009BAF39B03）

摘要/Abstract

摘要：

针对玻璃成形抛光中玻璃与抛光轮接触点相对线速度持续减小从而影响加工效率的问题,以控制相对线速度基本恒定、保证加工效率和精度为目标，提出基于三次NURBS曲线的速度控制算法。基于线性加减速方案，确定速度特性曲线控制点。结合Preston公式，以相对线速度基本恒定为约束条件，求解抛光轮中心末速度。以加加速度连续为约束条件，求取与控制点对应的权因子，确定抛光轮中心速度变化时的控制方程。采用四阶龙格-库塔数值方法确定插补初始点，再由米勒-汉明数值方法进行迭代校正，实现参数式曲线插补控制算法。试验结果表明，该速度控制方法能够有效保持玻璃与抛光轮接触点相对线速度基本恒定，加工效率较传统方法有较大提高。

关键词: 玻璃抛光, 三次NURBS曲线, 相对线速度, 预测校正插补算法

Abstract:

To deal with low machining productivity and quality due to continuous decreasing of relative velocity at touch point between glass and polishing wheel, a velocity control algorithm based on cubic NURBS was proposed to keep the limited relative velocity fluctuation. Based on linear acceleration/deceleration, the control points for proposed velocity control curve were confirmed. Using the Preston equation, the final velocity of polishing wheel center for velocity control curve was solved under the conditions of limited relative velocity fluctuation. Based on jerk continuity, the weighting factors were obtained and control equations for velocity smoothly changing were confirmed. Using fourth Runge-Kutta formula to obtain the initial points and Milne-Hamming equation to predict and correct the next points, the interpolation algorithm for parametric trajectory was accomplished. Experimental results show that the proposed approach guarantees limited fluctuation of relative velocity at touch point and improves the efficiency of glass polishing compared with traditional method.

Key words: glass polishing, cubic NURBS, relative velocity, predictor-corrector interpolation algorithm

中图分类号:

TP24

韩俊昭, 任锟, 潘骏, 刘思路, 尤灵敏, 沈琦琦. 玻璃成形抛光相对线速度基本恒定控制算法研究[J]. 中国机械工程, 2013, 24(24): 3272-3277.

Han Junzhao, Ren Kun, Pan Jun, Liu Silu, You Lingmin, Shen Qiqi. Research on Limited Relative Velocity Fluctuation in Glass Shaping Polishing[J]. China Mechanical Engineering, 2013, 24(24): 3272-3277.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/

https://www.cmemo.org.cn/CN/Y2013/V24/I24/3272

参考文献

[1]刘缙.平板玻璃的加工[M].北京:化学工业出版社,2008.
[2]陈金身, 智红梅. 一种玻璃抛光用新型抛光盘的研究[J]. 金刚石与磨料磨粒工程, 2012, 33(3): 78-81.
Chen Jinshen, Zhi Hongmei. Research on New Polis-hing Disk for Glass Polishing[J]. Diamond Abrasives Engineering, 2012, 33(3): 78-81.
[3]俞红祥 ,徐洪, 袁巨龙. 基于接触力控制的抛光轮磨损在线补偿策略研究[J]. 仪器仪表学报, 2010(5): 991-997.
Yu Hongxiang, Xu Hong, Yuan Julong. Study on Online Wearing Compensation Strategy for Polishing Wheel Based on Contacting Force Control[J]. Chinese Journal of Scientific Instrument, 2010,31(5):991-997.
[4]Lai J Y, Lin K Y, Tseng S J, et al. On the Development of a Parametric Interpolator with Confined Chord Error, Feedrate, Acceleration and Jerk[J]. International Journal of Advanced ManufacturingTechnology, 2008, 37: 104-121.
[5]Dong Jinyan, Ferreira P M, Stori J A. Feedrate Optimization with Jerk Constraints for Generating Minimum-time Trajectories[J]. International Journal of Machine Tools & Manufacture, 2007, 47: 1941-1955.
[6]Rew K H, Ka C W, Kim K S. A Practically EfficientMethod for Motion Control Based on AsymmetricVelocity Profile[J]. International Journal of Advanced Manufacturing Technology, 2009, 49: 678-682.
[7]姬俊锋, 周来水, 张得礼. NURBS曲线插补过程中运动平滑处理[J]. 中国机械工程, 2006, 17(21): 2225-2228.
Ji Junjeng, Zhou Laishui, Zhang Deli. Motion Smoothing Implementation for NURBS Curve Interpolation[J]. China Mechanical Engineering, 2006, 17(21): 2225-2228.
[8]赵巍, 王太勇, 万淑敏. 基于NURBS曲线的加减速控制方法研究[J]. 中国机械工程, 2006,17(1): 1-3.
Zhao Wei, Wang Taiyong, Wan Shumin. Acceleration-deceleration Control Method Based on NURBS Curve[J]. China Mechanical Engineering, 2006, 17(1): 1-3.
[9]Yong T, Narayanaswami R. A Parametric Interpolator with Confined Chord Error, Acceleration and Deceleration for NC Machining[J]. Computer-Aided Design, 2003, 35: 1249-1259.
[10]Piegl L, Tiller W. The NURBS Book[M]. Berlin:Springer-Verlag, 1996.
[11]刘军强, 高佳宏, 李言. 规则曲线和曲面的NURBS表示[J]. 西安工业学院学报, 2004, 24(4): 311-315.
Liu Junqiang, Gao Jiahong, Li Yan. The NURBS Expression of Several Characteristic Curve and Surface[J]. Journal of Xi'an Institute of Technology, 2004, 24(4): 311-315.
[11]Demirci I, Mezghani S, Mansori E. On Material Removal Regimes for the Shaping of Glass Edges: Force Analysis, Surface Topography and Damage Mechanisms[J]. Tribology Letters, 2008, 30: 141-150.

[1]	赵丁选, 郭瑞, 王硕, 闫长长, 王子鹤, 张天赐. 复杂地形环境下无人步履式挖掘机的车身姿态规划方法[J]. 中国机械工程, 2026, 37(1): 233-242.
[2]	郭万金, 田玉祥, 利乾辉, 曹雏清, 赵立军, 徐明坤, 刘孝恒, 侯旭栋. 未知环境下机器人打磨自适应变阻抗恒力控制[J]. 中国机械工程, 2026, 37(1): 92-104.
[3]	妥吉英, 徐笑南, 李俊, 张玉琛, 黄安, 胡都, 刘梓林. 一种基于改进SAC算法的六轴机械臂路径规划[J]. 中国机械工程, 2025, 36(12): 2986-2992.
[4]	印峰, 黄欣, 周佳义. 基于流模型的冗余机器人逆运动学解高精度计算[J]. 中国机械工程, 2025, 36(12): 2960-2967.
[5]	张雷, 杨聪楠, 李崴一, 赵一洁, 王晓聪. 变高度双轮足平台自适应平衡控制算法设计[J]. 中国机械工程, 2025, 36(12): 2920-2926.
[6]	倪涛, 赵亚辉, 赵泽仁, 杨凯强. 6-UPRU并联机器人动力学建模及基本动力学参数确定[J]. 中国机械工程, 2025, 36(12): 2911-2919.
[7]	杨明星, 沈佳乐, 高鹏, 张兴, 王俊翔. 连续体机器人设计与导向路径损失补偿策略[J]. 中国机械工程, 2025, 36(12): 2820-2828.
[8]	梁海平, 卢耀安, 连伟嘉, 王成勇. 考虑冗余自由度的六轴机器人光顺运动路径规划方法[J]. 中国机械工程, 2025, 36(11): 2652-2657.
[9]	董佳祥, 刘铨权, 胡希平, 赵学智. 新型刚柔混联连续体机器人运动建模[J]. 中国机械工程, 2025, 36(11): 2678-2684.
[10]	戴尧, 曾勇, 赵雪雅, 万俊豪, 顾金彤, 祝欣怡. 凸起凹陷特征表面的机器人变位姿喷涂涂层均匀性优化研究[J]. 中国机械工程, 2025, 36(11): 2694-2703.
[11]	梁继煌, 汪炜锋, 吴海彬. 基于6D光笔的工业机器人高精度示教方法[J]. 中国机械工程, 2025, 36(11): 2710-2719.
[12]	唐欣尧, 殷榕, 王旭鹏, 杨佳音, 刘晓宜, 郝雨阳. 膝踝关节外骨骼人机匹配性设计与优化[J]. 中国机械工程, 2025, 36(10): 2369-2378.
[13]	张来喜, 赵杨昊宇, 朱盛杰, 马凯威, 徐丰羽. 双驱动器仿肺软体机器人建模与变形分析[J]. 中国机械工程, 2025, 36(10): 2379-2388.
[14]	张颢曦, 姜杰, 蒋刚, 李月, 郝兴安. 黏土环境下六足机器人抬腿阻滞力学模型研究[J]. 中国机械工程, 2025, 36(09): 1996-2002.
[15]	刘建林, 黄海松, 范青松, 马驰, 张浪浪. 基于改进樽海鞘群算法的机械臂多目标轨迹规划研究[J]. 中国机械工程, 2025, 36(09): 2047-2056.