立式捏合机搅拌桨曲面的NURBS表示与误差分析

中国机械工程 ›› 2013, Vol. 24 ›› Issue (6): 826-830.

立式捏合机搅拌桨曲面的NURBS表示与误差分析

展俊德;李锡文;史铁林

华中科技大学，武汉，430074

出版日期:2013-03-25 发布日期:2013-04-08
基金资助:
国家自然科学基金资助项目(51075161)；中央高校基本科研业务费资助项目(2010MS090)
National Natural Science Foundation of China（No. 51075161）;
Fundamental Research Funds for the Central Universities( No. 2010MS090)

NURBS Surface of Vertical Kneader Stirring Blade and Its Error Analysis

Zhan Junde;Li Xiwen; Shi Tielin

Huazhong University of Science and Technology，Wuhan，430074

Online:2013-03-25 Published:2013-04-08
Supported by:

National Natural Science Foundation of China（No. 51075161）;
Fundamental Research Funds for the Central Universities( No. 2010MS090)

摘要/Abstract

摘要：

依据搅拌桨水平截面轮廓线的理论坐标点，反求生成了NURBS曲线;按照搅拌桨的螺旋升角，生成了一组不同高度截面轮廓线的NURBS曲线;利用蒙皮方法，生成了搅拌桨的NURBS曲面。提出了一种新的控制顶点投影法求解点到NURBS曲面最小距离的算法，用于计算搅拌桨的NURBS曲面的重构误差。结果表明，立式捏合机搅拌桨的NURBS曲面重构精度高，研究结果可为搅拌桨曲面优化设计提供借鉴。


关键词: 立式捏合机搅拌桨, 截面轮廓线, 蒙皮曲面, 控制顶点投影法, 曲面误差分析

Abstract:

According to the theoretical points of stirring blade horizontal sectional contour curve,a NURBS sectional curve was generated in reverse. Based on the helix angle of stirring blade,a set of different height NURBS sectional curves were produced. Using skinning surface method, the stirring blade NURBS surface was formed. The projection method of control points was proposed for calculating the minimum distance between a point and NURBS surface,to obtain the reconstruction errors of stirring blade NURBS surface. The results show that the NURBS surface reconstruction precision of vertical kneader stirring blade is high, which lays a good foundation for future stirring blade optimization design.

Key words: vertical kneader stirring blade, sectional contour, skinning surface, projection method of control point;surface error analysis

中图分类号:

TP391.7

展俊德, 李锡文, 史铁林. 立式捏合机搅拌桨曲面的NURBS表示与误差分析[J]. 中国机械工程, 2013, 24(6): 826-830.

ZHAN Dun-De, LI Ti-Wen, SHI Tie-Lin. NURBS Surface of Vertical Kneader Stirring Blade and Its Error Analysis[J]. China Mechanical Engineering, 2013, 24(6): 826-830.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/

https://www.cmemo.org.cn/CN/Y2013/V24/I6/826

参考文献

[1]叶定友,张德雄.中国航天固体火箭推进技术的发展[J].中国航天,2002,0(12):24-27.
[2]王正方,翟瑞清.立式捏合机搅拌桨的设计[J].固体火箭技术,1993(1):65-69.
[3]朱心雄等著.自由曲线曲面造型技术[M],2000:391.
[4]施法中.计算机辅助几何设计与非均匀有理B样条(CAGD&NURBS)[M].北京:高等教育出版社,2001.211-248.
[5]张乐年,周来水.基于复杂曲线的NURBS蒙皮曲面[J].工程图学学报,1996(2):58-63.
[6]Piegl L A, Tiller W. Algorithm for Approximate NURBS Skinning[J]. Computer-- aided Design, 1996, 28(9): 699-706.
[7]Yoshimasa T. Skinning--Surface Generation Based on Spine--Curve Control[J]. The Visual Comput- er, 2000, 16(2): 134-140.
[8]于丕强[2],施锡泉[1].双三次NURBS曲面的G^1连续性条件[J].大连理工大学学报,2004,44(3):330-333.
[9]柯映林[1],李奇敏[1].基于截面轮廓的NURBS曲面重建[J].中国机械工程,2005,16(12):1083-1087.
[10]DyllongE, Luther W. Distance Calculation Be- tween a Point and a NURBS Surface[C]//4th In- ternational Conference on Curves and Surfaces. Saint--Malo, 1999: 55-62.
[11]Piegl L A,Tiller W. Parameterization for Surface Fitting in Reverse Engineering[J]. Computer--ai- ded Design, 2001, 33(8): 593-603.
[12]Ma Y L, Hewitt W T. Point Inversion and Projec- tion for NURBS Curve and Surface: Control Pol- ygon Approach[J]. Computer-- aided Geometric Design, 2003, 20(2): 79-99.
[13]Selimovic I. Improved Algorithms for the Projec- tion of Points on NURBS Curves and Surfaces[J]. Computer Aided Geometric Design, 2006, 23(2) : 439-445.
[14]PieglL A, Rajab K, Smarodzinava V, et al. Point-- Distance Computations: A Knowledge--Guided Approach[J]. Computer--aided Design and Ap- plications, 2008, 5(6): 855-866.
[15]Zhou J, Sherbrooke E C, Patrikalakis N M. Com- putation of Stationary Points of Distance Func- tions[J]. Engineering with Computers, 1993,9 (4) : 231-246.