Influences of Key Structural Parameters of Hydraulic Piston Pump on Cavitation

Abstract

Abstract: In order to focus noises, vibrations and component corrosions caused by the cavitation in hydraulic plunger pump, a numerical simulation was conducted through full cavitation model and k-ε turbulence model to study the distribution of gas-phase volume fraction at various positions in plunger chamber and the generation mechanism of the distribution and the cavitation at relief grooves. The relation between depth of level 1- relief groove with its gas-phase volume fraction and impulse frequency in plunger pump. The results reveal that cavitations occur mainly at the intake areas, and the gas-phase volumes get to the largest fraction at the moment while water touching the inlet of port plate, and reducing dip angle of the sloping plate the gas phase volume fraction and its lasting period are decreased. Increasing the depth of level 1-relief groove wakens the cavitation, but it strengthens the peak pressure and pressure pulsation rate.

Key words: hydraulic plunger pump, cavitation, sloping plate angle, primary unloading groove depth

摘要： 针对水压柱塞泵由于空化引起的噪声、振动以及元件的腐蚀等问题，基于全空化模型与k-ε湍流模型，分析了柱塞腔在不同位置的气相体积分数的分布以及该分布产生的机理、卸荷槽处产生空化的机理，得到了不同斜盘倾角下柱塞腔和配流盘吸水口处气相体积分数随转角变化的特性曲线，以及一级卸荷槽深度与其气相体积分数和柱塞腔压力脉动率的关系。数值计算结果表明：空化主要发生在位于吸水区域的柱塞腔;与配流盘吸水口接触瞬时的柱塞腔的气相体积分数最高；减小斜盘倾角可以减小柱塞腔和配流盘吸水口的气相体积分数与持续时间;增大一级卸荷槽深度可以减小卸荷槽处空化程度，但会增大柱塞腔的压力尖峰和压力脉动率。

关键词: 水压柱塞泵, 空化, 斜盘倾角, 一级卸荷槽深度

CLC Number:

TH137.51

GAO Dianrong1;SUO Xiaoyu1;CAI Qianling2;WU Shaofeng1;LIANG Yingna1. Influences of Key Structural Parameters of Hydraulic Piston Pump on Cavitation[J]. China Mechanical Engineering.

高殿荣1;索晓宇1;蔡倩玲2;毋少峰1;梁英娜1. 水压柱塞泵关键结构参数对泵内空化的影响[J]. 中国机械工程.

References

[1]刘春节，吴小峰，干为民，等. 基于全空化模型的柱塞泵内空化流动的数值模拟[J]. 中国机械工程，2015,26(24):3341-3347.
LIU Chunjie, WU Xiaofeng, GAN Weimin,et al.Numerical Simulation of Cavitation Flow in Piston Pump Based on Full Cavitation Model[J]. China Mechanical Engineering,2015,26(24):3341-3347.

[2]陆亮. 液压节流阀中的空化流动与噪声[D]. 杭州：浙江大学，2012.
LU Liang. Cavitating Flow and Noise in Hydraulic Throttling Valves[D]. Hangzhou: Zhejiang University,2012.
[3]築地徹浩, 陈卓，陈晶晶. 轴向柱塞泵内部空化流的可视化分析[J]. 液压与气动，
2015(2)： 1-7.
ZHUDI Chehao,CHEN Zhuo,CHEN Jingjing. Visualized Analysis of Cavitation Inside Axial Pump[J]. Chinese Hydraulics & Preumatices,2015(2):1-7.
[4]翟江. 海水淡化高压轴向柱塞泵的关键技术研究[D]. 杭州：浙江大学，2012.
ZHAI Jiang.Investigation into the Key Problems of Axial Piston Pump for Seawater Desalination [D]. Hangzhou:Zhejiang University, 2012．
[5]吉晨. 受限制空间内的气泡行为数值与实验研究[D]. 杭州：浙江大学，2013.
JI Chen. Numerical and Experimental Research of Bubble Behavior in Restricted Space[D]. Hangzhou: Zhejiang University,2013.
[6]黄新良. 变量齿轮泵的CFD分析[J]. 机床与液压，2015，43 (2) ：143-149.
HUANG Xinliang．CFD Analysis of Variable Gear Oil Pump[J].Machine Tool & Hydraulics，2015，43（2）：143-149.
[7]董旭旭. 变量齿轮泵的空化流动[D]. 上海：上海工程技术大学,2013.
DONG Xuxu. Testing and Research on Cavitation Flow in Variable Gear Pump[D].Shanghai: Shanghai University of Engineering Science, 2013.
[8]赵飞. 混流式水轮机空化流动特性分析[J]. 西华大学学报(自然科学版)，2012，31（2）：69-72.
ZHAO Fei. Cavitation Characteristic Analysis of Francis Turbine[J]. Journal of Xihua University(Natural Science), 2012, 31 (2): 69-72.
[9]翟江. 水压轴向柱塞泵内部空化流动数值模拟[J]. 液压与气动，2012，43（11）：245-260.
ZHAI Jiang.Numerical Simulation of Cavition Flow in Water Hydraulic Axial Piston Pump[J]. Chinese Hydraulics & Preumatices, 2012, 43(11): 245-260.
[10]王海燕. 轴向柱塞泵汽蚀机理及仿真研究[D]. 太原：中北大学，2014.
WANG Haiyan. The Cavitation Mechanism and Simulation Research of Axial Piston Pump[J].Taiyuan: North University of China, 2014.
[11]郜立焕，刘世亮，杨毅，等. 基于CDF的轴向柱塞泵配流盘仿真[J]. 液压与气动，2008(6) ：42-44.
GAO Lihuan, LIU Shiliang, YANG Yi, et al. CFD Simulation of Valve Plate in Axial Piston Pump[J]. Chinese Hydraulics & Preumatices, 2008(6): 42-44.
[12]马吉恩. 轴向柱塞泵流量脉动及配流盘优化设计研究[D]. 杭州：浙江大学， 2009.
MA Ji'en. Study on Flow Ripple and Valve Plate Optimizion of Axial Piston Pump[D]. Hangzhou: Zhejiang University, 2009.

[1]	YU Kexin1；SHANG Qunli1；WU Xin2. Analysis of Cavitation Characteristics for Orifice Plates [J]. China Mechanical Engineering, 2021, 32(03): 290-296.
[2]	QIN Yalu1,3;CAI Wei1,3;WANG Liugen1,3;LEI Zheng2;ZHAO Jingyi1,3;WANG Qiming2. Numerical Study of Cavitation Effects of Electro-hydraulic Actuator System of FAST [J]. China Mechanical Engineering, 2021, 32(02): 171-179.
[3]	SUN Yi;HUANG Shaowei;MAO Yalang;ZHU Lihao. Effects of Ultrasonic Cavitation Micro Jet-flow on Impact Fine Particle Breakage Near Rigid Walls [J]. China Mechanical Engineering, 2019, 30(24): 2953-2960.
[4]	CHEN Tieniu;GUO Zhongning;ZENG Baiwen;YIN Sihua. Study on Micro-hole Polishing Mechanism and Experiments Based on Laser-induced Cavitation Bubbles [J]. China Mechanical Engineering, 2018, 29(03): 273-278,285.
[5]	WANG Zhaohui1;HU Ya'nan1;RAO Changjian1;DENG Xiaogang2. Numerical Analysis of Cavitation Effects of Self-excited Oscillation Pulse Nozzles and Jet Forms [J]. China Mechanical Engineering, 2017, 28(13): 1535-1541.
[6]	Xia Dongsheng, Sun Changguo, Yu Yan, Zhang Huichen. 3D Unsteady Numerical Simulation of Magnetostriction-induced Ultrasonic Cavitation Flow [J]. China Mechanical Engineering, 2016, 27(22): 3061-3067.
[7]	Li Ting, Ma Jien, Zhang Yu, Fang Youtong. Lubrication Characteristics Analyses of Ferrofluid Bearing Based on CFD Simulation [J]. China Mechanical Engineering, 2016, 27(07): 939-944.
[8]	Zhang Xiaoqiang, Zhu Xijing, Wang Jianqing. Study on Single Cavitation Bubble Collapse Temperature in Ultrasonic Vibration Honing [J]. China Mechanical Engineering, 2016, 27(06): 796-800.
[9]	Gao Yongqiang, Wei Mingrui, Tan Baohua, Yan Fuwu, Dong Weitao. Numerical Simulation of Internal Flow of Nozzles and Near-field Sprary with OpenFOAM [J]. China Mechanical Engineering, 2016, 27(01): 79-84.
[10]	Liu Chunjie, Wu Xiaofeng, Gan Weimin, He Yafeng. Numerical Simulation of Cavitation Flow in Piston Pump Based on Full Cavitation Model [J]. China Mechanical Engineering, 2015, 26(24): 3341-3347.
[11]	Ye Linzheng, Zhu Xijing, Guo Ce. Ultrasonic Cavitation Micro-jet Modeling and Simulation [J]. China Mechanical Engineering, 2015, 26(21): 2890-2894.
[12]	Li Sihai, Yuan Shihao. Study on Two-stage Throttle Port Cavitation Characterization [J]. China Mechanical Engineering, 2015, 26(16): 2165-2169,2221.
[13]	Zhang Junhong;Li Zhouyu;He Zhenpeng;Zhang Guichang;Xie Weisong. Research on Cavitation Effect on Lubrication Performance for Misaligned Journal Bearings [J]. China Mechanical Engineering, 2013, 24(21): 2913-2920.
[14]	SHU Chao, ZHANG Jian-Hua, CHANG Wei-Jie, WANG Chao, SONG Xi-Chao. #br# Theoretical Analysis and Verification for Flow Field of Ultrasonic Vibration Aided Electro-discharge Milling [J]. China Mechanical Engineering, 2012, 23(14): 1712-1717.
[15]	WANG Xiu-Li-1, YUAN Shou-Ji-1, SHU Rong-Sheng-1, SHU Zhi-Jun-2, PENG Wei-Jiang-2. Numerical Simulation and Experimental Study for Cavitations in Centrifugal Pump Impeller with Splitters [J]. China Mechanical Engineering, 2012, 23(10): 1154-1157.