Analysis of Motion and Deformation Characteristics of Ink Distributing System of Offset Printing Machine

Abstract

Abstract:

In order to analyze the movement and deformation of an ink distributing system, a model of ink distributing roller and ink vibrator was built using ANSYS, the characteristics and influence factors of the movement, deformation, shearing stress and normal stress of the ink distributing roller were analyzed. The results show that, the movement of ink distributing roller is influenced mainly by ink vibrator's rotating speed and oscillating amplitude, the normal stress of ink distributing roller is influenced mainly by its hardness, the shearing stress is influenced mainly by its hardness and the friction coefficient between two rollers, and the deformation of ink distributing roller is influenced mainly by its hardness and oscillating amplitude and rotating speed of the ink vibrator. The results are very important for the study of printing color quality control.

Key words: offset printing machine, ink distributing system;movement;deformation;stress

摘要：

为分析胶印机匀墨系统的运动和变形，利用ANSYS建立了匀墨系统中串墨辊和匀墨辊的模型，分析了匀墨辊运动、变形、剪切应力、正应力的特点及影响因素。分析结果显示：匀墨辊运动主要受串墨辊转速和串墨辊窜动量的影响;匀墨辊正应力主要受其硬度的影响;匀墨辊剪切应力主要受其硬度和两墨辊间摩擦因数的影响;匀墨辊变形主要受其硬度、串墨辊窜动量、串墨辊转速的影响。

关键词: 胶印机, 匀墨系统, 运动, 变形, 受力

CLC Number:

TH123

Chu Hongyan, Zhao Juntao, Yan Xiaofei, Cai Ligang. Analysis of Motion and Deformation Characteristics of Ink Distributing System of Offset Printing Machine[J]. China Mechanical Engineering, 2014, 25(4): 527-533.

初红艳, 赵俊涛, 严晓飞, 蔡力钢. 胶印机匀墨系统运动及变形特性分析[J]. 中国机械工程, 2014, 25(4): 527-533.

References

[1]余节约，刘真. 胶印机串墨性能的仿真研究[J]. 包装工程，2009，30(11) ：66-68.
Yu Jieyue, Liu Zhen. Simulation the Effects of Vibarator Oscillation of Offset Printing[J]. Packaging Engineering, 2009, 30(11): 66-68.
[2]Ahmed Dewan Hasan，Sung Hyung Jin，Kim Dong-Soo. Simulation of Non-Newtonian Ink Transfer between Two Separating Plates for Gravure-offset Printing[J]. International Journal of Heat and Fluid Flow，2011，32(1)：298-307.
[3]马茹菲．卷筒纸胶印机输墨系统性能分析及仿真研究[D]．西安：西安理工大学，2008.
[4]武秋敏．胶印机输墨系统的仿真研究[D]．西安：西安理工大学，2005.
[5]王仪明，蔡吉飞，赵吉斌．高速胶印机关键技术研究现状及进展[J]．中国机械工程，2007，18(10)：1255-1258.
Wang Yiming, Cai Jifei, Zhao Jibin. Research and Development of Key Technologies for High Speed Offset Presses[J]. China Mechianical Engineering,2007,18(10):1255-1258.
[6]Tanimoto K，Kohno K，Seto H．Thermo—viscoe-lastic Analysis of Rubber——covered Rolls Taking Account of Heat Generation[J]．Transactions of the Japan Society of Mechanical Engineers Part A，2002，68(1)：154-160．
[7]周洪星，成刚虎．墨辊的弹性变形对输墨系统性能的影响[J]．印刷杂志，2007(10)：58-60.
Zhou Hongxing, Cheng Ganghu. Influence of Ink Roller’s Resilient Deformation on Ink Distribution Roller’s Performance[J]. Printing Field,2007(10):58-60.
[8]陈振欢．胶印机输墨系统油墨流动的数值模拟分析[D]．北京：北京工业大学，2010.
[9]杨咸启，李晓玲. 现代有限元理论技术与工程应用[M]. 北京：北京航空航天大学出版社，2007.
[10]王忠于，成刚虎，代春英. 胶印机串墨辊轴向速度的分析[J]. 轻工机械，2007，25(4)：41-43.
Wang Zhongyu, Cheng Ganghu, Dai Chunying. Analysis of Offset Vibrating Rolling Axial Velocity[J]. Light Industry Machinery, 2007,25(4):41-43.
[11]李妍. 基于ANSYS软件的接触问题分析及在工程中的应用[D]．长春：吉林大学，2004.
[12]毛谦德，李振清. 袖珍机械设计师手册[M]. 北京：机械工业出版社，2007.
[13]徐培林，张淑琴. 聚氨酯材料手册[M]. 北京：化学工业出版社，2011.

[1]	CHEN Xiaohui1;CHEN Haofeng2;CHEN Xu3. Shakedown Analysis of Elbow Pipes of Nuclear Power Plants under Cyclic Loading Based on LMM [J]. China Mechanical Engineering, 2019, 30(19): 2269-2275.
[2]	ZHANG Kaiyuan;YIN Yanguo;ZHANG Guotao;XIE Zhiyuan;CHEN Qi. Tribological Properties of FeS/iron-based Bearing Materials by High Energy Ball Milling-Powder Metallurgy Method [J]. China Mechanical Engineering, 2019, 30(18): 2172-2178.
[3]	CHU Hongyan;CHEN Libo;AN Ran;CAI Ligang. Analysis of Ink Temperature of Ink Roller Extrusion Contact Areas Based on Thermal Elastohydrodynamic Lubrication [J]. China Mechanical Engineering, 2018, 29(23): 2773-2778.
[4]	TANG Pengpeng1;WEN Wen1;HUANG Yongan2;LIU Qian1. Influences of Bending Radius on Delamination of Flexible Electronic Devices [J]. China Mechanical Engineering, 2017, 28(19): 2354-2359.
[5]	CHEN Qiang, LAN Jian, HUA Lin, . Analysis of Whole Contact Stresses of Tapered Roller Bearings under Radial Forces，Axial Forces and Moment Loads [J]. China Mechanical Engineering, 2017, 28(10): 1178-1182.
[6]	CHEN Huanguo, CAI Li, CHEN Wenhua, CHEN Pei, YI Yongyu, LI Yajie. Effects of Inclusions of Complex Shape on Cracks of Wheel Rim [J]. China Mechanical Engineering, 2017, 28(02): 240-245.
[7]	Zhang Jianzhuo, Du Zhichun, Wang Jie, Sui Xin. Study on Self Defense Delay Valve of High Voltage Circuit Breaker [J]. China Mechanical Engineering, 2016, 27(12): 1662-1666.
[8]	Zhao Jinjuan, Wang Shijun, Yang Chao, Wang Shiyi, Yang Huixin. A Constitutive Law Based on Transverse Isotropic Hypothesis and Finite Element Model of Fixed Joints [J]. China Mechanical Engineering, 2016, 27(08): 1007-1011.
[9]	Chen Guiping, Wen Guilin. Parameterized Modeling and Modal Analysis of High Speed Grinding Machine Structure [J]. China Mechanical Engineering, 2015, 26(18): 2415-2418.
[10]	Wang Yao, Wang Jianmei, Xiang Dan, . Simulation and Experiments on Stress Characteristics of Arc Binding Interface for Oil-film Bearings [J]. China Mechanical Engineering, 2015, 26(14): 1851-1856.
[11]	Tong Shuiguang, Wang Xiangbing, We Chao, Zhang Shuai. Research on Fatigue Life Prediction Methodof for Arm Structure of Hydraulic Excavator [J]. China Mechanical Engineering, 2014, 25(16): 2167-2172.
[12]	Liu Jiayan, Cheng Zhifeng, Wang Ping, . Design and Applications of Rubber Shock Absorber in Airborne Photoelectric Pod [J]. China Mechanical Engineering, 2014, 25(10): 1308-1312.
[13]	Ma Ping;Mo Deyun;Wu Guangrong. Effects of Step Dynamic Interference Fit on Transmitting Torque Capacity of Motorized Spindle [J]. China Mechanical Engineering, 2013, 24(21): 2933-2938.
[14]	Wang Yanwei;Li Yafei;Huang Zhengdong. Research on Collaborative Optimization Method of Mechanical Parts,Mechanical System and #br# Controller Parameters in Mechatronic Products and Its Applications [J]. China Mechanical Engineering, 2013, 24(21): 2955-2959.
[15]	CHI Yu-Lun, LI Hao-Lin. #br# #br# Study on Ball Screw Grinding Chatter and Monitoring Method [J]. China Mechanical Engineering, 2012, 23(22): 2748-2751.