Analysis of Metal Flow and Process of Back Gear with Double Boss in Warm Forging

Abstract

Abstract:

Based on the geometric features of back gear with double boss, a new two-step warm forging process before finishing was put forward to reduce the number of cold forging process. Empty corners in the bottom of profile of all teeth were found when using the above process. In order to solve the problem, a rigid plastic FE model was built to simulate the warm forging process. The velocity, stress and strain field were investigated, and the metal flow rules were discussed with the experimental results. Then a qualified gear was achieved through expanding the radial wave shape by means of an indentation established in die. The measured results show that the new process can satisfy a high level precision of forging. The work presented herein may be used as basic data for the design of the precision forging processes.

Key words: back gear with double boss, metal flow, warm forging, corner

摘要：

根据齿部带有倒锥的双毂倒挡齿轮结构特点,提出了一种两步温锻+冷精整的新工艺。以某双毂倒挡齿轮零件为例进行实验发现齿形下角隅充填不满,为解决此问题建立了齿轮温锻成形过程的刚塑性有限元仿真模型，分析了其速度、应力与应变等场量信息，结合盐酸热蚀后的金属流线探讨了成形过程中金属的流动规律，通过在模具上设置凹槽增大金属径向扩展“波形”最终使得轮齿角隅充填饱满。齿轮测量仪检测结果表明：采用提出的新工艺能够获得满足双毂倒挡齿轮要求的轮齿齿形。

关键词: 双毂倒挡齿轮, 金属流动, 温锻, 角隅

CLC Number:

TG316

Li Heng, Chen Wenlin, Zhou Rui, Shi Weibing, Wu Yucheng. Analysis of Metal Flow and Process of Back Gear with Double Boss in Warm Forging[J]. China Mechanical Engineering, 2014, 25(24): 3364-3367,3390.

李亨, 陈文琳, 周瑞, 施卫兵, 吴玉程. 双毂倒挡齿轮温锻成形金属流变行为及工艺研究[J]. 中国机械工程, 2014, 25(24): 3364-3367,3390.

References

[1]胡成亮,赵震,刘全坤,等.倒挡齿轮冷锻成形有限元模拟[J].中国机械工程,2009,20(18):2250-2254.
Hu Chengliang, Zhao Zhen, Liu Quankun, et al. Finite Element Simulation on Cold Forging Process of Back Gear[J]. China mechanical Engineering,2009,20(18):2250-2254.
[2]胡成亮,施卫兵,徐祥龙,等.带毂直齿轮冷精锻新工艺及其数值模拟[J].上海交通大学学报,2009,43(9):1494-1497.
Hu Chengliang, Shi Weibing, Xu Xianglong, et al. A Novel Cold Precision Forging Process of Spur Gear with Boss and Its Numerical Simulation[J]. Journal of Shanghai Jiaotong University,2009,43(9):1494-1497.
[3]Feng W, Hua L, Han X H. Finite Element Analysis and Simulation for Cold Precision Forging of a Helical Gear[J]. J. Cent. South Univ., 2012,19:3369-3377.
[4]王岗超,薛克敏,许锋,等.齿腔分流法冷精锻大模数圆柱直齿轮[J].塑性工程学报,2010,17(3):18-21.
Wang Gangchao, Xu Kemin, Xu Feng, et al. Simulation and Experimental Study on Cold Precision Forging with Flow Dividing in Dentiform Cavity for Spur Gear of Big Modulus[J]. Journal of Plasticity Engineering,2010, 17(3):18-21.
[5]谭险峰, 刘霞, 熊洪淼, 等.圆柱直齿轮精锻成形工艺仿真及试验[J]. 塑性工程学报, 2010, 17(1):22-26.
Tan Xianfeng, Liu Xia, Xiong Hongmiao, et al. Simulation and Experimental Research on the Precision Forging of Spur Gear[J]. Journal of Plasticity Engineering,2010, 17(1):22-26.
[6]Bach F W, Behrens B A, Dahndel H, et al. Integration of Heat Treatment in Precision Forging of Gear Wheels[J]. The Arabian Journal for Science and Engineering, 2005, 30:102-112.
[7]朱怀沈, 夏巨谌, 金俊松, 等.大模数直齿轮温冷锻精整量的优化选择[J]. 塑性工程学报,2011,18(1): 53-57.
Zhu Huaishen, Xia Jushen, Jin Junsong, et al. Optimization of Sizing Amount during Warm-cold Compound Forging for Spur Gear with Big Modulus[J]. Journal of Plasticity Engineering, 2011, 18(1):53-57.
[8]Deng X B, Hua L, Han X H, et al. Numerical and Experimental Investigation of Cold Rotary Forging of A 20CrMnTi Alloy Spur Bevel Gear[J]. Materials and Design, 2011,32: 1376-1389.
[9]Khalilpourazary S, Dadvand A, Azdast T, et al. Design and Manufacturing of a Straight Bevel Gear in Hot Precision Forging Process Using Finite Volume Method and CAD/CAE Technology[J]. International Journal of Advanced Manufacturing Technology, 2011, 56(1/4):87-95.
[10]胡成亮,刘全坤,刘永熙,等.齿轮锻造金属流动规律分析及工艺改进[J].机械工程学报,2008,44(5):186-190.
Hu Chengliang, Liu Quankun, Liu Yongxi, et al. Analysis of Metal Flow and Technology Improvement on Gear Forging[J]. Chinese Journal of Mechnical Engineering, 2008, 44(5):186-190.

[1]	ZHANG Dazhi, GUAN Mingsheng, ZHANG Qingdong, WANG Aiguo, ZHOU Xinliang. Simulation of Deformation Behaviors and Laws of Steel Pipes in Rolling Processes of Retained Mandrel Pipe Mills [J]. China Mechanical Engineering, 2020, 31(22): 2691-2698.
[2]	DONG Zhikui1，3;PENG Liwei1;JIAO Yunjing1;SUN Jianliang 1，2;ZHUO Chaoyue 1;ZHAO Jingyi1;LU Mingli 3;YANG Zhiming3;WANG Peiliang3. Rolling Force Model of Large Conical Cylinders Considering Conical Metal Flow [J]. China Mechanical Engineering, 2019, 30(19): 2385-2393.
[3]	LIU Qingling;LUO Ping;YU Changjuan. Compliance Calculation and Behavior Analysis of a Novel Right Circular Corner-filled Hybrid Multiple-axis Flexure Hinge [J]. China Mechanical Engineering, 2018, 29(20): 2479-2483.
[4]	LI Yuxi1;LI Yan1;CUI Limu1;YANG Mingshun1;XIAO Jiming1;CUI Fengkui2. Study on Shaping Parameter Control of Lead Screw Cold Roll-Beating [J]. China Mechanical Engineering, 2017, 28(19): 2388-2393.
[5]	JIA Zhen1; LI Yan1;HAN Zhiren1;XIAO Yong2;FAN Zuojun1. Effects of Sheet Blank Shapes on Axial Spinning Depths of Square Section Die-less Spinning [J]. China Mechanical Engineering, 2017, 28(18): 2262-2267.
[6]	CHAI Tian, LI Fan, LEI Fei, LIU Jie, ZENG Xia , TANG Yingshi, . Study on Steering Geometry of Racing Cars with Consideration of Tire Cornering Characteristics [J]. China Mechanical Engineering, 2017, 28(09): 1106-1111.
[7]	Sun Tao, Xu Zhengjin, You Lin, Huang Xu, Zheng Songlin, Zhang Zhendong, . Cornering-time Optimal Algorithm for Intelligent Scaled Vehicle Based on Kalman Filter [J]. China Mechanical Engineering, 2015, 26(19): 2693-2697.
[8]	Wang Limei;Liu Rui. Strategy of Hybrid Acc/Dec Look-ahead Planning Interpolation for Multi-block NURBS Curves [J]. China Mechanical Engineering, 2014, 25(3): 388-392.
[9]	DIAO Lei, GONG Yan. Rotation Precision Analysis of Corner-filleted Flexure Hinge [J]. China Mechanical Engineering, 2013, 24(6): 715-720.
[10]	WANG Guo-Lin, LIANG Xin-Xin. #br# Research on Vehicle Inverse Dynamics Based on Compages of Tires' Characteristics for Handling and Stability [J]. China Mechanical Engineering, 2013, 24(3): 422-425.
[11]	. Compliance Matrix Analysis of Corner-filleted Flexure Hinge [J]. China Mechanical Engineering, 2013, 24(18): 2462-2468.
[12]	ZHANG Lu, LI Yan, YANG Meng-Shun, LI Bin. #br# Study on Metal Flowing of Lead Screw Cold Roll-beating Forming [J]. China Mechanical Engineering, 2012, 23(13): 1623-1628.
[13]	YANG Nie-Fang, HUANG Yu-Mei, LI Yan, GAO Feng. Sub-pixel Corner Detection Algorithm of Chessboard Image Based on Improved SUSAN Operator [J]. China Mechanical Engineering, 2010, 21(21): 2541-2545.
[14]	JIU Hong, ZUO Dui-Wen, ZHANG Min, HONG Hong-Feng. Research on Metal Flow of Internal Thread of High Strength Steel during Cold Extrusion for Aircraft Landing Gear [J]. China Mechanical Engineering, 2010, 21(14): 1714-1718.
[15]	Wang Jing, ;Wang Deyou;Han Qingkai. Mechanism Analysis and Treatment on Loss Corner Faults of Compressor Blades [J]. J4, 2008, 19(9): 0-1133.