Analysis of a 7-DOF Automated Fiber Placement Robotic Manipulator's Self-Motion Manifolds

Abstract

Abstract:

The position joint space manifold and posture joint space manifold of a redundant robotic manipulator were defined,whose position and posture were decoupled,the redundant robotic manipulator's self-motion manifold can be obtained by pairing these manifolds.A 7-DOF automated fiber placement robotic
manipulator was analyzed using the defined self-motion manifolds,
and its self-motion manifolds were obtained.The results show that
the automated fiber placement robotic manipulator's
self-motion manifold is correct using this method by simulation,
and this method is also applicable in analyzing the self-motion manifold of
the redundant robotic manipulator which the position and posture are decoupled.

Key words: redundant robotic manipulator, position joint space manifold, posture joint space manifold, self-motion manifold

摘要：

定义了位姿解耦的冗余自由度机器人位置关节空间流形和姿态关节空间流形,将位置关节空间流形和姿态关节空间流形进行配对得到冗余自由度机器人的自运动流形。利用定义的位置关节空间流形和姿态关节空间流形对七自由度自动铺丝机器人进行分析,分别得出七自由度自动铺丝机器人的位置关节空间流形和姿态关节空间流形,配对以后得出七自由度自动铺丝机器人的自运动流形,并进行了仿真验证,结果表明这种分析方法得到的自动铺丝机器人的自运动流形是正确的,而且对于其他类型位姿解耦的冗余自由度机器人自运动流形分析也是适用的。

关键词: 冗余自由度机器人, 位置关节空间流形, 姿态关节空间流形, 自运动流形

CLC Number:

TP242.2

GE Xin-Feng. Analysis of a 7-DOF Automated Fiber Placement Robotic Manipulator's Self-Motion Manifolds[J]. China Mechanical Engineering, 2013, 24(12): 1591-1595.

葛新锋. 七自由度自动铺丝机器人的自运动流形分析[J]. 中国机械工程, 2013, 24(12): 1591-1595.

References

[1]刘亚威.F-35战斗机进气道的自动化制造[J].国防制造技术,2011,0(4):32-34.
[2]韩振宇[1],邵忠喜[1],富宏亚[1],刘源[1].S型进气道纤维铺放轨迹网格化生成[J].航空制造技术,2009(19):72-78.
[3]王连圭[1],马保离[2].冗余机器人系统的自运动控制[J].控制与决策,2003,18(2):199-202.
[4]张秋豪[1],孙汉旭[1],魏世民[1].改善冗余度机器人灵活性的研究[J].北京邮电大学学报,2004,27(4):74-77.
[5]陆震.冗余自由度机器人原理及应用[M].北京:机械工业出版社,2007..
[6]唐粲,负超,栾胜.一种新型医疗机器人运动学及灵活性分析[J].北京航空航天大学学报,2004,27(4):74-77.
[7]贾庆轩[1],褚明[1],孙汉旭[1],洪磊[1].9-DOF超冗余机器人轨迹规划优化算法[J].北京邮电大学学报,2008,31(2):20-25.
[8]Burdick J W. On the Inverse Kinematics of Redun- dant Manipulators: Characterization of the Self- Motion Manifolds[-C//IEEE International Confer- ence on Robotics and Automation. New York: IEEE, Council on Robotics and Automation, 1989: 264-270.
[9]Moll M, Kavraki L E. Path Planning for Minimal Energy Curves of Constant Length[-C//Proceed- ings of the 2004 IEEE International Conference on Robotics and Automation. New Orleans:Institute of Electrical and Electronics Engineers, 2004:2826 - 2831.
[10]Muller A. Collision Avoiding Continuation Method for Inverse Kinematics of Redundant Manipulator [C]//Proceedings of the 2004 IEEE International Conference on Robotics and Automation. New Or- leans: Institute of Electrical and Electronics Engi- neers, 2004 : 1593-1598.
[11]Joel W B. On the Inverse Kinematics of Redundant Manipulator: Characterization of the Self-motion Manifold[C]//Proceedings of the 1989 IEEE In- ternational Conference on Robotics and Automa- tion. New York : IEEE, 1989 : 264-270.
[12]赵建文[1],姚玉峰[1],黄博[1].一种位姿耦合式冗余度机器人的自运动流形[J].机械科学与技术,2009(8):1012-1017.
[13]Moll M, Kavraki L E. Path Planning for Minimal Energy Curves of Constant Length[-C]//Proceed- ings of the 2004 IEEE International Conference on Robotics and Automation. New Orleans Institute of Electrical and Electronics Engineers, 2004 : 2826- 2831.
[14]Burdick J W. Kinematics Analysis and Design of Redundant Robot Manipulators I-D1. California Stanford University, 1980.

[1]	CHEN Zhuofan, ZHOU Kun, QIN Feifei, WANG Binrui. Inverse Kinematics Solution of Robots Based on IQPSO Algorithm [J]. China Mechanical Engineering, 2024, 35(02): 293-304.
[2]	YE Bosheng, JIN Xiongcheng, LI Han, SHAO Baiyan, LI Xiaokun, LI Siao. Robot Error Compensation Algorithm by Pseudo Target Iterative Generation [J]. China Mechanical Engineering, 2024, 35(01): 136-143.
[3]	LI Jiaxuan, LI Lun, ZHOU Bo, ZHAO Jibin, ZHU Guang, WANG Zhengjia, . A Robotic Multi-directional Polishing Trajectory Generation Method Based on Preston-PSO Algorithm [J]. China Mechanical Engineering, 2023, 34(14): 1729-1740.
[4]	ZHANG Yinan, DING Jianwan. Friction Model of Robot Joints Considering Influences of Temperature [J]. China Mechanical Engineering, 2023, 34(02): 127-134.
[5]	TUO Junbo, PENG Qiuyuan, ZHANG Xianmin, LI Congbo. Energy Consumption Prediction Method for Industrial Robots [J]. China Mechanical Engineering, 2022, 33(22): 2727-2732,2740.
[6]	NI Huakang, YANG Zeyuan, YANG Yifan, CHEN Xindu, YAN Sijie, DING Han. Robot Kinematics Calibration Method Considering Base Frame Errors [J]. China Mechanical Engineering, 2022, 33(06): 647-655.
[7]	JIANG Dezheng, HU Jun, ZHONG Heng, WANG Hongguang, SONG Yifeng, YUAN Bingbing, . Analysis of Safe Adsorption Conditions and Motion Characteristics of Rolling Sealed Tracked Wall-climbing Robot [J]. China Mechanical Engineering, 2021, 32(22): 2757-2764.
[8]	ZHANG Enzheng, TANG Ningmin, CHEN Gang, LIU Cuiping. Industrial Robot Calibration Based on Improved IGG3 Weight Function of Distance Error Model#br# [J]. China Mechanical Engineering, 2021, 32(13): 1539-1546.
[9]	JI Yangzhen, HOU Li, LUO Lan, LUO Pei, LIU Xubin, LIANG Shuang. Solution of Inverse Kinematics for 6R Robots Based on Combinatorial Optimization Algorithm#br# [J]. China Mechanical Engineering, 2021, 32(10): 1222-1232.
[10]	XIAO Fan;LI Guang;YOU Yulong. Multiple Module Neural Network Solving for Inverse Kinematics of Space 3R Manipulators [J]. China Mechanical Engineering, 2019, 30(10): 1233-1238.
[11]	LIU Yang;ZHAO Chen;WANG Xuhao;ZHANG Jiajun . A New Model of Spray Robot Electrostatic Rotating Cups [J]. China Mechanical Engineering, 2019, 30(06): 709-715.
[12]	ZHANG Tie1;LI Changda1;QIN Binbin1;LIU Xiaogang2. Adaptive Iterative Learning Control of Trajectory Tracking of SCARA Robots [J]. China Mechanical Engineering, 2018, 29(14): 1724-1729.
[13]	HAN Jiang;GU Taotao;XIA Lian;DONG Fangfang. Joint Trajectory Planning Algorithm for Industrial Robots Based on Mixed Interpolation [J]. China Mechanical Engineering, 2018, 29(12): 1460-1466.
[14]	ZHANG Xu1;JIA Junhui1;ZHANG Gang2. Eye-on-Hand Calibration Method Based on Specular Reflection [J]. China Mechanical Engineering, 2018, 29(10): 1153-1158,1165.
[15]	ZHANG Tie;ZHANG Bin. Optimized Interpolation Algorithm for Robotic Belt Grinding Processes [J]. China Mechanical Engineering, 2018, 29(08): 983-990.