Research on Springback Defects in Incremental Forming of Cu-Al Bimetal

doi:10.3969/j.issn.1004-132X.2021.03.013

Abstract

Abstract: In order to discuss the influences of different processing parameters on springback in incremental forming of bimetals, a three-dimensional model was established including the tool head, laminated sheet and composite interface. The parameters of the interface cohesion elements were obtained by comparing the results of T-peeling, and the reliability of the finite element model was verified through experiments. The experimental results show that the forming angle is the most critical factor affecting the springback, and tool diameter is least sensitive to springback. In addition, the cohesive element may effectively simulate the interface of the laminated sheets, and the simulation error is only 7.9%. The analysis shows that the step-down size, sheet thickness and tool diameter are positively related to the springback values, the forming angle is negatively related to the springback ones. And the springback value decreases by 21% as the forming angle increases from 30° to 60°.

Key words: Cu-Al bimetal, incremental forming, finite element analysis, cohesive element, springback defect

摘要： 为了讨论不同工艺参数对复合板渐进成形回弹的影响，建立了包含工具头、复合板材和复合界面的三维有限元模型,通过对比T形剥离结果得到复合界面内聚力单元参数，通过实验验证了有限元模型的可靠性。实验结果表明，成形角对双金属复合板渐进成形回弹最敏感，工具头直径对回弹敏感度最低,另外，内聚力单元能有效模拟双金属复合板结合界面，模拟误差仅为7.9%。分析结果表明，单层下压量、板厚、工具头直径都与回弹量成正相关，成形角与回弹量成负相关，成形角从30°增大至60°时回弹量减小21%。

关键词: 铜铝复合板, 渐进成形, 有限元分析, 内聚力单元, 回弹缺陷

CLC Number:

TH16

QIN Qin1,2 ；HE Liu1；LI Cheng2；ZANG Yong1. Research on Springback Defects in Incremental Forming of Cu-Al Bimetal[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2021.03.013.

秦勤1,2；何流1；李程2；臧勇1. 铜铝复合板渐进成形回弹缺陷研究[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2021.03.013.

References

［1］DUFLOU J R, HABRAKEN A, CAO J, et al. Single Point Incremental Forming:State-of-the-Art and Prospects［J］. International Journal of Material Forming, 2018,11(6):743-773.
［2］BYKOV A A. Bimetal Production and Applications［J］. Steel in Translation, 2011,41(9):778-786.
［3］SEDIGHI M, HONARPISHEH M. Investigation of Cold Rolling Influence on Near Surface Residual Stress Distribution in Explosive Welded Multilayer［J］. Strength of Materials, 2012,44(6):693-698.
［4］LI Y, CHEN X, LIU Z, et al. A Review on the Recent Development of Incremental Sheet-forming Process［J］. The International Journal of Advanced Manufacturing Technology, 2017,92:2439-2462.
［5］BEHERA A K, de SOUSA R A, INGARAO G, et al. Single Point Incremental Forming:an Assessment of the Progress and Technology Trends from 2005 to 2015［J］. Journal of Manufacturing Processes, 2017, 27:37-62.
［6］Al-GHAMDI K A, HUSSAIN G, HASHEMI R, SPIF of Cu/Steel Composite Sheet:Effect of Heat Treatment on Bond Force and Formability［J］. Materials and Manufacturing Processes, 2016, 31(6):758-763.
［7］崔震，高霖，徐岩. 数控渐进成形中的鼓包问题分析［J］. 机械科学与技术，2008,12(27):1581-1585.
CUI Zhen, GAO Lin, XU Yan, et al. Analyses of the Bump Phenomenon in Sheet Metal Incremental Forming［J］. Mechanical Science and Technology for Aerospace Engineering, 2008,12(27):1581-1585.
［8］RADU M C, CRISTEA I. Processing Metal Sheets by SPIF and Analysis of Parts Quality［J］. Materials and Manufacturing Processes, 2013,28(3):287-293.
［9］HUSSAIN G, GAO L, HAYAT N. Forming Parameters and Forming Defects in Incremental Forming of an Aluminum Sheet:Correlation, Empirical Modeling, and Optimization:Part A［J］. Materials and Manufacturing Processes, 2011,26(12):1546-1553.
［10］AMBROGIO G, FILICE L, de NAPOLI L ,et al. A Simple Approach for Reducing Profile Diverting in a Single Point Incremental Forming Process. Proceedings of the Institution of Mechanical Engineers, Part B［J］. Journal of Engineering Manufacture, 2005,219(11):823-830.
［11］DEJARDIN S, THIBAUD S,GELIN J C, et al. Experimental Investigations and Numerical Analysis for Improving Knowledge of Incremental Sheet Forming Process for Sheet Metal Parts［J］. Journal of Materials Processing Technology, 2010,210(2):363-369.
［12］ISIDORE B B L , HUSSAIN G, SHAMCHI S P ,et al. Prediction and Control of Pillow Defect in Single Point Incremental Forming Using Numerical Simulations［J］. Journal of Mechanical Science and Technology, 2016,30(5):2151-2161.
［13］史晓帆. 金属板料渐进成形精度控制技术研究［D］.南京：南京航空航天大学, 2013.
SHI Xiaofan. Research on Accuracy Control Technology in Incremental Sheet Metal Forming［D］.Nanjing:Nanjing University of Aeronautics and Astronautics,2013.
［14］韩飞, 莫健华, 龚攀. 基于遗传神经网络的数字化渐进成形回弹预测［J］.华中科技大学学报(自然科学版), 2008, 36 (1):121-124
HAN Fei, MO Jianhua, GONG Pan. Incremental Sheet NC Forming Springback Prediction Using Genetic Neural Network［J］. Journal of Huazhong University of Science & Technology(Nature Science Edition), 2008, 36 (1):121-124.
［15］HONARPISHEH M, KEIMASI M, ALINAGHIAN I. Numerical and Experimental Study on Incremental Forming Process of Al/Cu Bimetals:Influence of Process Parameters on the Forming Force, Dimensional Accuracy and Thickness Variations［J］. Journal of Mechanics of Materials and Structures, 2018,13(1):35-51.
［16］HONARPISHEH M, JOBEDAR M M, ALINAGHIAN I. Multi-response Optimization on Single-point Incremental Forming of Hyperbolic Shape Al-1050/Cu Bimetal Using Response Surface Methodology［J］. The International Journal of Advanced Manufacturing Technology, 2018,96:3069-3080.
［17］GHEYSARIAN A , HONARPISHEH M. An Experimental Study on the Process Parameters of Incremental Forming of Explosively-welded Al/Cu Bimetal［J］. Journal of Computational & Applied Research in Mechanical Engineering, 2017,7(1):73-83.
［18］LIU Zhaobing, LI Guohao. Single Point Incremental Forming of Cu-Al Composite Sheets:a Comprehensive Study on Deformation Behaviors［J］. Archives of Civil and Mechanical Engineering,2019,19(2):484-502.
［19］Al-GHAMDI K A , HUSSAIN G. SPIF of Cu/Steel Clad Sheet:Annealing Effect on Bond Force and Formability［J］. Materials and Manufacturing Processes, 2016,31(6):758-763.
［20］Al-GHAMDI K A , KHALID A, HUSSAIN G. On the Comparison of Formability of Roll-bonded Steel-Cu Composite Sheet Metal in Incremental Forming and Stamping Processes［J］. The International Journal of Advanced Manufacturing Technology, 2016,87:267-278.
［21］王晓强.基于内聚力模型的复合材料拉伸性能细观有限元分析［D］.哈尔滨：哈尔滨工程大学，2012.
WANG Xiaoqiang. Meso-finite Element Analysis of the Tensile Properties of Composites Based on Cohesive Model［D］. Harbin:Harbin Engineering University, 2012.
［22］MADER E, GAO S L, PLONKA R. Enhancing the Properties of Composites by Controlling Their Interphase Parameters［J］. Advanced Engineering Materials, 2004,6(3):147-150.
［23］DUGDALE D S. Yielding of Steel Sheets Containing Slits［J］. Journal of the Mechanics and Physics of Solids, 1960, 8(2):100-104.
［24］BARENBLATT G I. The Mathematical Theory of Equilibrium Cracks in Brittle Fracture［J］. Advances in Applied Mechanics, 1962,7：55-129.
［25］李龙. 车身单搭接粘接接头静强度性能试验及强度预测方法的研究［D］. 长春：吉林大学，2011.
LI Long. Research on Static Strength Analysis and Strength Prediction of Adhesively Bonded Single Lap Joint for Automotive［D］. Changchun:Jilin University, 2011.
［26］陈兴.基于内聚力模型的不锈钢钎焊接头裂纹扩展研究［D］.上海：华东理工大学，2014.
CHEN Xing . The Study on the Crake Propagation of Stainless Steel Brazed Joints by Using Cohesive Zone Model［D］. Shanghai:East China University of Science and Technology, 2014.
［27］张宁.不锈钢钎焊接头剥离强度的研究［D］. 上海：华东理工大学，2013.
ZHANG Ning .Peel Strength of the Brazed Stainless Steel Joint［D］.Shanghai：East China University of Science and Technology, 2013.
［28］KOU J F, XU F , GUO J P ,et al. Damage Laws of Cohesive Zone Model and Selection of the Parameters［J］. Journal of Mechanical Strength, 2011,33(5):714-718.
［29］SU C , WEI Y J, ANAND L. An Elastic-plastic Interface Constitutive Model:Application to Adhesive Joints［J］. International Journal of Plasticity, 2004,20(12):2063-2081.

[1]	HU Chao, LIU Zuo-Min. Research on Rolling Bearing’s Heathcote’s Stick-slip Model Based on Materials Compatibility [J]. J4, 201016, 21(16): 1969-1973.
[2]	TUN Jian, Jocher Dietrich, LI Jiang. Research on Sheet Metal Digital Incremental Forming Technology without Support [J]. J4, 201016, 21(16): 2002-2005,2015.
[3]	LI Ming, DAI Peipei, CHANG Zhidong, CHEN Jun, . Springback Control and Compensation of Incremental Forming for Sheet Metal Parts with Open Geometric Feature [J]. China Mechanical Engineering, 2020, 31(22): 2723-2727.
[4]	ZHANG Yaoman;BAO Fengxu;QI Peining. Modeling Method for Thermal Characteristics of Ball Screw Pairs [J]. China Mechanical Engineering, 2020, 31(20): 2486-2490,2496.
[5]	HOU Xiaoli;LI Yan;YANG Mingshun;BAI Lang;SHI Xun;ZHANG Chengxing. Research on FLC in CNC Single Point Incremental Forming of Aluminum Sheets [J]. China Mechanical Engineering, 2020, 31(08): 960-967.
[6]	XU Qinghe1;WANG Min1;CHEN Wenliang1;LIU Dengwei2. Layered Mapping Method of Local Displacement Field for Panel Deformation Prediction [J]. China Mechanical Engineering, 2019, 30(23): 2870-2876,2883.
[7]	ZHU Hu1;XIAO Dongxuan1;KANG Jaeguan2. STL Model Based Interference Check and Correction in Double Sided CNC Incremental Forming [J]. China Mechanical Engineering, 2019, 30(23): 2890-2897.
[8]	BAI Lang;LI Yan;YANG Mingshun;LIN Yunbo;ZHAO Renfeng;YUAN Qilong. Research on Overall Accuracy of SPIF Parts [J]. China Mechanical Engineering, 2019, 30(22): 2748-2756.
[9]	CHEN Xiaohui1;CHEN Haofeng2;CHEN Xu3. Shakedown Analysis of Elbow Pipes of Nuclear Power Plants under Cyclic Loading Based on LMM [J]. China Mechanical Engineering, 2019, 30(19): 2269-2275.
[10]	LIU Peilei;YANG Shiqiang;BAI Lele;LI Zhuo;LI Dexin. Wear Model of Disc Hob Cutter Rings Based on Abrasive Wear [J]. China Mechanical Engineering, 2019, 30(15): 1782-1789.
[11]	LI Binbin1,2;ZHAO Youkun1;LIU Jie1. Research on Load Distribution Characteristics for Web-flange Splice Structures [J]. China Mechanical Engineering, 2019, 30(09): 1041-1048.
[12]	YANG Qinghua;QIN Zhengyong;WANG Zhiheng;BAO Guanjun. Influences of Two-dimensional Electro-hydraulic Flutters on Cold Extrusion Forming [J]. China Mechanical Engineering, 2019, 30(05): 621-629.
[13]	SHI Xun;LI Yan;YANG Mingshun;YAO Zimeng;HOU Xiaoli. Study on Single Point Incremental Forming Processes of Corrugated Tubes [J]. China Mechanical Engineering, 2018, 29(20): 2507-2514.
[14]	DONG Yude1;LI Jiucheng1;YANG Shanlai2;CHEN Minglong1;WANG Nan1. Parameterized Method for Personalized Oriented Welded Cinder Ladles [J]. China Mechanical Engineering, 2018, 29(12): 1446-1453.
[15]	ZHAO Xiaoyu1，2;ZHANG Shuren1. Lightweight Design Method for Electric Vehicle Battery Boxes Made by Composite Materials [J]. China Mechanical Engineering, 2018, 29(09): 1044-1049.