跳跃机器人能量转换的主动控制与试验测试

doi:10.3969/j.issn.1004-132X.2022.24.007

摘要/Abstract

摘要： 针对现有跳跃机器人能量转换效率低的问题，设计了一种新型跳跃机器人，以实现利用非圆齿轮的啮合主动控制能量的有效存储和释放。基于机器人机构学原理，设计了跳跃机器人的主体结构，分析了其运动原理，给出了其弹跳运动流程。根据预先给定的机器人能量转换曲线中的关键参数，以能量转换曲线研究非圆齿轮节曲线，以非圆齿轮共轭啮合特性研究跳跃机器人的能量转换特性，建立了非圆齿轮传动的数学模型，并通过具体实例详细说明了非圆齿轮的设计过程。使用3D打印技术制作了跳跃机器人原理样机，开展试验测试研究。研究结果表明，跳跃机器人可以实现稳定跳跃，且能量转换效率的测量值与预先给定的理论值较吻合。

关键词: 跳跃机器人, 能量转换, 主动控制, 非圆齿轮, 啮合

Abstract: To change the present situations of the low energy conversion efficiency, a new type hopping robot was proposed. The basic thought was to control the energy storage and release by non-circular gear meshing. Based on the principles of robot mechanisms, the main structure of the hopping robots was built. Motion principle was analyzed and motion procedure of the hopping robots was developed. According to the pre-given key parameters of energy conversion curve, pitch curves of non-circular gears were investigated by exploring the energy conversion curves, while hopping properties of hopping robots were revealed by exploring meshing properties of non-circular gears. The mathematical models of non-circular gear transmission were established. A detailed introduction about the design processes of non-circular gears was given by using examples. Using 3D printing technique, the robot prototype was developed, and the experiments for hopping robots were carried out. The results confirm that the stable hopping may be realized, and the experimental results are close to the pre-given values.

Key words: hopping robot, energy conversion, active control, non-circular gear, meshing

中图分类号:

TP242

王建, 缪龙, 张文祥, 王树坤. 跳跃机器人能量转换的主动控制与试验测试[J]. 中国机械工程, 2022, 33(24): 2961-2970.

WANG Jian, MIAO Long, ZHANG Wenxiang, WANG Shukun. Active Control Method for Energy Conversion and Experimental Test of Hopping Robots[J]. China Mechanical Engineering, 2022, 33(24): 2961-2970.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/10.3969/j.issn.1004-132X.2022.24.007

http://www.cmemo.org.cn/CN/Y2022/V33/I24/2961

参考文献

［1］王国彪，陈殿生，陈科位，等．仿生机器人研究现状与发展趋势［J］．机械工程学报，2015, 51(13):27-44.
WANG Guobiao, CHEN Diansheng, CHEN Kewei, et al. The Current Research Status and Development Strategy on Biomimetic Robot［J］. Journal of Mechanical Engineering, 2015, 51(13):27-44.
［2］刘壮志．弹跳机器人若干关键技术研究［D］．南京：南京航空航天大学，2004.
LIU Zhuangzhi. Research on Several Critical Technique about the Jumping Robots［D］. Nanjing： Nanjing University of Aeronautics and Astronautics, 2004.
［3］HALDANE D W, PLECNIK M M, YIM J K, et al. Robotic Vertical Jumping Agility via Series-elastic Power Modulation［J］. Science Robotics, 2016, 1(1):1-9.
［4］HURST J W, CHESTNUTT J E, RIZZI A A. The Actuator with Mechanically Adjustable Series Compliance［J］. IEEE Transactions on Robotics, 2010, 26(4):597-606.
［5］HAM R V, VANDERBORGHT B, DAMME M V, et al. MACCEPA, the Mechanically Adjustable Compliance and Controllable Equilibrium Position Actuator:Design and Implementation in a Biped Robot［J］. Robotics and Autonomous Systems, 2007, 55(10):761-768.
［6］VANDERBORGHT B, TSAGARAKIS N G, HAM R V, et al. MACCEPA 2.0:Compliant Actuator Used for Energy Efficient Hopping Robot Chobino1D ［J］. Autonomous Robots, 2011, 31(1):55-65.
［7］GUENTHER F, IIDA F. Energy-efficient Monopod Running with a Large Payload Based on Open-loop Parallel Elastic Actuation［J］. IEEE Transactions on Robotics, 2017, 33(1):102-113.
［8］韩亚丽，郝大彬，于建铭，等．新型多模式弹性驱动器的弹跳性能研究［J］. 机械工程学报，2016, 52(9):96-104.
HAN Yali, HAO Dabin, YU Jianming, et al. Bounce Performance Study on Novel Multi-mode Elastic Actuator［J］. Journal of Mechanical Engineering, 2016, 52(9):96-104.
［9］KOH J S，JUNG S P，NOH M，et al. Flea Inspired Catapult Mechanism with Active Energy Storage and Release for Small Scale Jumping Robot［C］∥IEEE International Conference on Robotics and Automation.Karlsruhe, Germany, 2013:26-31.
［10］PLANTE J S, DEVITA L M, DUBOWSKY S. A Road to Practical Dielectric Elastomer Actuators Based Robotics and Mechatronics:Discrete Actuation［C］∥Electroactive Polymer Actuators and Devices. San Diego, USA, 2007:6-21.
［11］BERGBREITER S, PISTER K S J. Design of an Autonomous Jumping Micro-robot［C］∥IEEE International Conference on Robotics and Automation. Rome, Italy, 2007:447-453.
［12］李向阳，葛文杰，杨方．考虑脚部柔性的仿袋鼠跳跃机器人运动特性研究［J］．机器人, 2006, 28(4):374-376.
LI Xiangyang, GE Wenjie, YANG Fang. Locomotion Analysis of Hopping Kangaroo Robots Considering Foot Compliance［J］. Robot, 2006, 28(4):374- 376.
［13］CHEN D S, YIN J M, HUANG Y, et al. A Hopping-righting Mechanism Analysis and Design of the Mobile Robot［J］. Journal of the Brazilian Society of Mechanical Science and Engineering, 2013, 35(4):469-478.
［14］何广平，李士明．可调刚度弹性机器人关节研究与设计［J］．北方工业大学学报，2012, 24(3):37-41.
HE Guangping, LI Shiming. Research and Design of Adjustable Stiffness Elastic Robots Joint［J］. Journal of North China University of Technology, 2012, 24(3):37-41.
［15］柴辉，葛文杰，魏敦文，等．一种间歇式弹跳机器人的机构设计与跳跃性能分析［J］．机械工程学报，2012, 48(13):19-26.
CHAI Hui, GE Wenjie, WEI Dunwen, et al. Mechanism Design and Hopping Performance Analysis of an Intermittent Hopping Robot［J］. Journal of Mechanical Engineering, 2012, 48(13):19-26.
［16］李渤涛，陈定方．非圆齿轮设计、制造、检测及应用［J］．机械工程学报，2020, 56(9):55-72.
LI Botao, CHEN Dingfang. Design, Manufacture, Inspection and Application of Non-circular Gears［J］. Journal of Mechanical Engineering, 2020, 56(9):55-72.
［17］OTTAVIANO E, MUNDO D, DANIELI G A, et al. Numerical and Experimental Analysis of Non-circular Gears and Cam-follower Systems as Function Generators ［J］. Mechanism and Machine Theory, 2008, 43(8):996-1008.
［18］牛石从，李革，李国一，等．茶叶自动杀青理条机新型传动机构设计［J］．农机化研究，2011 (2):58-61.
NIU Shicong, LI Ge, LI Guoyi, et al. The Design of New Transmission in Automatic Fixation-shaping Machine［J］. Journal of Agricultural Mechanization Research, 2011, 33(2):58-61．
［19］雷昌毅，陈建能，李鹏鹏，等．非圆齿轮-曲柄滑块压捆机构反求设计［J］．农业工程学报，2012, 28(13):22-27.
LEI Changyi, CHEN Jianneng, LI Pengpeng, et al.Reverse Design of Non-circular Gear-crank Slider Hay Baler Mechanism［J］. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(13):22-27.
［20］胡紫阳，杨辉，李大柱，等．平流泵用非圆齿轮副的优化设计及实验分析［J］．中国机械工程，2016, 27(22):3082-3087.
HU Ziyang, YANG Hui, LI Dazhu, et al. Optimization Design and Experimental Analysis of Non-circular Gears for Constant Flow Pumps［J］. China Mechanical Engineering, 2016, 27(22):3082-3087.
［21］BURROWS M, SUTTON G. Interacting Gears Synchronize Propulsive Leg Movements in a Jumping Insect［J］. Science, 2013, 341(6151):1254-1256.
［22］WANG J, FAN J M, FENG Y. The Design Methodology and Characteristics Analysis of a Uniform-variable Non-circular Gear Drive［J］. International Journal on Interactive Design and Manufacturing, 2019, 13(3):821-830.

[1]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[2]	胡波, 安锦运, 尹来容, 周长江. 小模数齿轮传动的时变啮合刚度计算方法[J]. 中国机械工程, 2024, 35(01): 74-82.
[3]	郝壮壮, 张庆春, 胡云波, 郭宜斌, 王东华, 李玩幽. 齿面摩擦和几何偏心对含变位直齿轮啮合刚度的影响研究[J]. 中国机械工程, 2023, 34(23): 2812-2823.
[4]	魏冰阳, 古德万, 王永强, 杨建军, . 高减比准双曲面齿轮摩擦功耗分析与效率试验[J]. 中国机械工程, 2023, 34(13): 1525-1532.
[5]	韩江, 李振富, 田晓青, 费宁忠, 夏链, . 内啮合强力珩齿工件齿面珩削纹理预测与控制方法研究[J]. 中国机械工程, 2023, 34(01): 10-16.
[6]	孟宗, 李佳松, 潘作舟, 庞修身, 崔玲丽, 樊凤杰. 裂纹故障对轮齿时变啮合刚度的影响分析[J]. 中国机械工程, 2022, 33(16): 1897-1905，1911.
[7]	刘思远, 宋朝省, 朱才朝. 小交错角面铣准双曲面齿轮副的几何设计与啮合特性[J]. 中国机械工程, 2022, 33(13): 1521-1528,1536.
[8]	陈甜, 张兴武, , 刘金鑫, , 陈雪峰, , 严如强, . 自适应频谱塑形主动控制及舰艇领域应用研究进展[J]. 中国机械工程, 2022, 33(04): 482-495.
[9]	陈宗斌, 何琳, 廖健, . 直线共轭内啮合齿轮泵输出流量脉动的测试研究[J]. 中国机械工程, 2021, 32(15): 1801-1811.
[10]	沈双, 雷静桃, 张悦文. 仿生跳跃机器人气动串联弹性关节的位置/刚度控制[J]. 中国机械工程, 2021, 32(12): 1486-1493.
[11]	汪飞雪, 刘亚, 臧新良 . 非圆齿轮差动轮系往复机构反求设计与运动学分析[J]. 中国机械工程, 2021, 32(06): 697-704.
[12]	张静, 程肥肥, 宋宝林, 刘志刚, 张卫华. [设计与优化]基于协同优化算法的高速受电弓多学科设计优化[J]. 中国机械工程, 2021, 32(04): 490-498.
[13]	刘大伟1，2；刘佳佳1. 面向管道机器人的非对称惯性驱动系统及其动力学特性[J]. 中国机械工程, 2020, 31(18): 2189-2195，2205.
[14]	杜进辅, 王峥嵘, 刘凯, 文建爽, 毛锦. 纯电动汽车高速斜齿轮传动振动特性分析[J]. 中国机械工程, 2020, 31(15): 1808-1814.
[15]	林超1;夏锡光1;邢庆坤2;刘文思1. 非圆齿轮型间歇转动机构的设计与运动特性分析[J]. 中国机械工程, 2020, 31(10): 1142-1148.