大型起竖装备液压系统及其鲁棒切换控制策略

摘要/Abstract

摘要： 针对大型起竖装备液压系统供油压力与负载特性不匹配而导致能量损失严重的问题，通过对负载特性的分析，将其近似等效为“初始-中间-终了”三段式折线负载。在起竖初始阶段采用恒定高压，以提供足够驱动力；在中间阶段设定随起竖角度线性单调递减的线性压力，以降低系统能耗；在起竖终了阶段采用恒定低压，以保持起竖稳定，从而实现系统供油压力与起竖负载的近似匹配，降低系统能耗。针对供油压力切换可能导致起竖过程振动和不稳定的问题，通过建立液压系统数学模型，提出了鲁棒切换控制策略。仿真和实验结果均表明，起竖过程平稳，无振动和超调现象，油液温度比直接采用节流控制降低约40℃，表明该系统及其鲁棒切换控制策略能有效降低起竖过程的能量损失。

关键词: 起竖装备, 切换控制, 系统能耗, 液压系统, 负载匹配

Abstract: Aimed at high energy loss of large erecting equipment due to supply pressure unmatched with load characteristics, the load characteristics were analyzed, which was approximately equivalent to initial-middle-final three-segment broken line load. In initial stage of erection, constant high pressure was used to provide sufficient driving force; in middle stage, pressure decreases linearly and monotonously with the erection angle to reduce energy consumption of the system; in final stage, constant low pressure was used to maintain erection stability. The switching control strategy may match the oil supply pressure with approximate external loads and reduce energy consumption. Aiming at the problems that the switching of supply pressure might lead to vibration and instability in erection processes, a mathematical model of hydraulic system was built, and a robust control strategy was proposed. Experimental and simulation results show that the erecting processes are smooth, stable and not overshoot. The temperature of the oil is reduced about 40℃ compare with the throttle control, which shows the system and robust switched control strategy may save energy effectively.

Key words: erecting equipment, switched control, energy consumption, hydraulic system, load matched

中图分类号:

TH137

杨俊1;黄书舟1;曾乐2. 大型起竖装备液压系统及其鲁棒切换控制策略[J]. 中国机械工程.

YANG Jun1;HUANG Shuzhou1;ZENG Le2. Robust Switched Control Strategy of Large Erecting Equipment Hydraulic Systems[J]. China Mechanical Engineering.

参考文献

[1]DU C, PLUMMER R, JOHNSTON N. Performance Analysis of an Energy-efficient Variable Supply Pressure Electro-hydraulic Motion Control System[J]. Control Engineering Practice, 2016, 48(1): 10-21.
[2]郭晓松. 导弹起竖过程的载荷研究[J]. 兵工学报, 2008, 29(6): 718-721.
GUO Xiaosong. Load Analysis on Missile Erection[J]. Acta Armamentarii, 2008, 29(6): 718-721.
[3]杨俊, 曾乐, 谭建平. 液压比例系统特性分析与非对称控制策略 [J]. 华中科技大学学报(自然科学版), 2016, 44(5): 121-127.
YANG Jun, ZENG Le, TAN Jianping. Characteiistic Analysis of Hydraulic Proportional System and Asymetric Control Strategy[J]. Journal of Huazhong University of Science & Technology(Natural Science Edition), 2016, 44(5): 121-127.
[4]李良, 李锋, 冯永保,等. 基于自适应模糊滑模的大型液压起竖系统控制策略研究[J]. 兵工学报, 2016, 37(1): 71-76.
LI Liang, LI Feng, FENG Yongbao, et.al. Research on Control Strategy of Large Hydraulic Erecting System Based on Adaptive Fuzzy Sliding Mode[J]. Acta Armamentarii, 2016, 37(1): 71-76.
[5]董鑫, 张宏宇, 陈奇, 等. 基于负载敏感回路的起竖液压系统仿真 [J]. 导弹与航天运载技术, 2016(343): 21-25.
DONG Xin, ZHANG Hongyu, CHEN Qi, et al. Simulation on Erection Hydraulic System with Load Sensing Circuit[J]. Missiles and Space Vehicles, 2016(343): 21-25.
[6]杜文正,吴鹏, 张金星,等. 高阶滑模控制在液压起竖系统中的应用[J]. 机床与液压,2016,44(21): 69-77.
DU Wenzheng, WU Peng, ZHANG Jinxing, et al. Application of High Order Sliding Mode Control in Hydraulic Erecting System[J]. Machine Tool & Hydraulics, 2016, 44(21): 69-77.
[7]高永卫, 谭建平, 杨俊. 大型装备电液系统鲁棒控制策略与实验验证[J]. 锻压技术, 2015, 40(5): 90-95.
GAO Yongwei, TAN Jianping, YANG Jun. Control Strategy and Experimental Verification on Robust of Electro-hydraulic System in Large Equipment[J]. Forging and Stamping Technology, 2015, 40(5): 90-95.
[8]KOIVUM K J, MATTILA J. High Performance Nonlinear Motion/Force Controller Design for Redundant Hydraulic Construction Crane Automation[J]. Automation in Construction, 2015, 51(1):59-77.
[9]SIDHO L, BRUM X, SMAOUI M, et al. Dynamic Gains Differentiator for Hydraulic System Control[J]. Journal of Dynamic Systems, Measurement, and Control, 2015, 137(4): 04101-04107.
[10]YAN H, ZHU Y. Bang-bang Control Model for Uncertain Switched Systems[J]. Applied Mathematical Modelling, 2014, 15(1):1-10.
[11]WANG S. Generic Modeling and Control of an Open Circuit Piston Pump Part I: Theoretical Model and Analysis[J]. Journal of Dynamic Systems, Measurement and Control, 2016, 138(4): 041001-041004.
[12]JALAYERI E, IMAM A, SEPEHRI N. A Throttle-less Single Rod Hydraulic Cylinder Positioning System for Switching Loads[J]. Case Studies in Mechanical Systems and Signal Processing, 2015, 11(2):27-31.
[13]高钦和, 黄先祥. 多级缸起竖系统运动过程的建模与仿真[J]. 系统仿真学报, 2005, 17(7): 1563-1568.
GAO Qinhe, HUANG Xianxiang. Dynamic Modelling and Simulation of Erecting System with Multi-stage Cylinder[J]. Journal of System Simulation, 2005, 17(7): 1563-1568.
[14]黄先祥, 高钦和, 郭晓松. 大型装置起竖过程的动力学建模研究 [J]. 系统仿真学报, 2002, 14(3): 271-277.
HUANG Xianxiang, GAO Qinhe, GUO Xiaosong. Dynamic Modeling of Erected Process for Large Mechanism[J]. Journal of System Simulation, 2002, 14(3): 271-277.
[15]曽乐, 杨俊, 谭建平. 非零开口的阀控非对称缸系统不变性补偿控制 [J]. 华中科技大学学报(自然科学版), 2017, 45(3): 29-34.
ZENG Le, YANG Jun, TAN Jianping. Compensation Control of a Nonzero Open Valve Controlled Asymmetric Cylinder System Based on Model Invariance[J]. Journal of Huazhong University of Science & Technology(Natural Science Edition), 2017, 45(3): 29-34.