载荷对激光选区烧结Cf/SiC复合材料摩擦磨损性能的影响

摘要/Abstract

摘要： 通过激光选区烧结技术和液相渗硅工艺制备了碳纤维增强碳化硅（Cf/SiC）复合材料。试样组织由C、SiC和Si三相组成，其密度和弯曲强度分别为2.89±0.01 g/cm3和237±9.8 MPa。采用UMT TriboLab多功能摩擦磨损试验机研究了Cf/SiC复合材料在不同载荷(10 N, 30 N, 50 N和70 N)条件下的摩擦学特性。研究结果表明：载荷较小(10 N)时，Cf/SiC复合材料的磨损由微凸起和SiC硬质点造成，磨损机制为磨粒磨损；载荷为30 N时，复合材料的摩擦磨损综合性能最好，其平均摩擦因数为0.564，磨损率低(5.24×10-7 cm3/（N·m）)，主要磨损机制为犁削形成的磨粒磨损和黏结磨损。载荷增大到70N时，材料磨损严重，磨粒脱落形成凹坑，产生裂纹，其磨损率(8.68×10-7 cm3/（N·m）)高，磨损机制主要为脆性剥落。

关键词: 增材制造, 激光选区烧结, Cf/SiC复合材料, 载荷, 摩擦磨损性能

Abstract: Carbon fiber reinforced silicon carbide composites were prepared by SLS and liquid phase silicon infiltration. The composite microstructure consisted of three phases of C, SiC and Si. The density and flexural strength of the Cf/SiC composites were 2.89±0.01 g/cm3 and 237±9.8 MPa, respectively. The friction and wear properties of Cf/SiC composites under different loads (10N, 30N, 50N and 70N) were studied by UMT TriboLab multi-function friction and wear tester. The results show that the wear mechanism of the Cf/SiC composites caused by micro-protrusions and SiC hard sports is abrasive wear when the load is small (10 N). When the load is as 30N, the composites have the best comprehensive friction and wear properties, showing the average friction coefficient of 0.564, and low wear rate of 5.24×10-7 cm3/（N·m）. The main wear mechanism is abrasive wear and adhesive wear formed by plough. When the load is increased to 70 N, the wear is serious, and the particles fall off to form pits and cracks. It has a high wear rate (8.68×10-7 cm3/（N·m）). The wear mechanism is mainly brittle shedding.

Key words: addictive manufacturing, selective laser sintering(SLS), Cf/SiC composite, load, friction and wear property

中图分类号:

傅华;朱伟;郑沈威;闫春泽. 载荷对激光选区烧结Cf/SiC复合材料摩擦磨损性能的影响[J]. 中国机械工程.

FU Hua;ZHU Wei;ZHENG Shenwei;YAN Chunze. Effects of Load on Friction and Wear Properties of Cf/SiC Composites Prepared by SLS[J]. China Mechanical Engineering.

参考文献

[1]JANG G H, CHO K H, PARK S B, et al. Tribological Properties of C/C-SiC Composites for Brake Discs[J]. Metals and Materials International, 2010, 16(1): 61-66.
[2]季春云, 金晓怡, 陈志鹏. 碳化硅陶瓷摩擦磨损性能及摩擦过程中接触应力分析[J]. 润滑与密封, 2018, 43(2):78-81.
JI Chunyun, JIN Xiaoyi, CHEN Zhipeng. Friction and Wear Properties of Silicon Carbide Ceramics and Analysis of Contact Stress during Friction[J]. Lubrication and Sealing, 2018, 43(2):78-81.
[3]MEI H, LI H, BAI Q, et al. Increasing the Strength and Toughness of a Carbon Fiber/Silicon Carbide Composite by Heat Treatment[J]. Carbon, 2013, 54: 42-47.
[4]束成祥, 李晓阳, 余晓琴, 等. 反应烧结碳化硅陶瓷材料的摩擦磨损性能[J]. 理化检验(物理分册), 2013, 49(9):589-592.
SHU Chengxiang, LI Xiaoyang, YU Xiaoqin, et al. Friction and Wear Properties of Reactive Sintered Silicon Carbide Ceramic Materials[J]. Physical and Chemical Testing (Physical Section), 2013, 49(9):589-592.
[5]BYEONGCHOON G, INSIK C. Microstructural Analysis and Wear Performance of Carbon-fiber-reinforced SiC Composite for Brake Pads[J]. Materials, 2017, 10(7): 701.
[6]ZHOU X, ZHU D, XIE Q, et al.Friction and Wear Properties of C/C-SiC Braking Composites[J]. Ceramics International, 2012, 38(3): 2467-2473.
[7]LI Z, XIAO P, XIONG X, et al. Tribological Characteristics of C/C-SiC Braking Composites under Dry and Wet Conditions[J]. Transactions of Nonferrous Metals Society of China, 2008, 18(5): 1071-1075.
[8]LI G, YAN Q, XI J R, et al. The Stability of the Coefficient of Friction and Wear Behavior of C/C–SiC[J]. Tribology Letters, 2015, 58(1): 13.
[9]ZHOU H, SINGH R N. Kinetics Model for the Growth of Silicon Carbide by the Reaction of Liquid Silicon with Carbon[J]. Journal of the American Ceramic Society, 1995, 78(9): 2456-2462.
[10]JANG B K, SAKKA Y. Influence of Microstructure on the Thermophysical Properties of Sintered SiC Ceramics[J]. Journal of Alloys and Compounds, 2008, 463(1/2): 493-497.
[11]FU Z, SCHLIER L, TRAVITZKY N, et al. Three-dimensional Printing of SiSiC Lattice Truss Structures[J]. Materials Science and Engineering: A, 2013, 560: 851-856.
[12]史玉升, 钟建伟, 蔡道生, 等. 基于零件切片的选择性激光烧结预热温度控制方法[J]. 机械工程学报, 2006,42(6):67-72.
SHI Yusheng, ZHONG Jianwei, CAI Daosheng, et al. Selective Laser Sintering Preheating Temperature Control Method Based on Part Slicing[J]. Journal of Mechanical Engineering, 2006,42(6):67-72.
[13]杨家懿, 朱伟, 史云松,等. 激光选区烧结高分子纳米复合材料研究进展[J]. 高分子材料科学与工程, 2017, 33(6):184-190.
YANG Jiayi, ZHU Wei, SHI Yunsong, et al. Research Progress of Polymer Nanocomposites by Selective Laser Sintering[J]. Polymer Materials Science and Engineering, 2017, 33(6):184-190.
[14]潘腾, 朱伟, 闫春泽, 等. 激光选区烧结3D打印成形生物高分子材料研究进展[J]. 高分子材料科学与工程, 2016, 32(3):178-183.
PAN Teng, ZHU Wei, YAN Chunze, et al. Advances in 3D Printing of Biopolymer Materials by Selective Laser Sintering[J]. Polymer Materials Science and Engineering, 2016, 32(3):178-183.
[15]MEYERS S, KRUTH J P, VLEUGELS J. Direct Selective Laser Sintering of Reaction Bonded Silicon Carbide[C]∥Solid Freeform Fabrication Symposium. Austin, 2015:1750-58.
[16]ZHU W, FU H, XU Z, et al. Fabrication andCharacterization of Carbon Fiber Reinforced SiC Ceramic Matrix Composites Based on 3D Printing Technology[J]. Journal of the European Ceramic Society, 2018, 38(14): 4604-4613.
[17]FU H, ZHU W, XU Z, et al. Effect of Silicon Addition on the Microstructure, Mechanical and Thermal Properties of Cf/SiC Composite Prepared via Selective Laser Sintering[J]. Journal of Alloys and Compounds, 2019, 792, 1045-1053.
[18]LUO Z H, JIANG D L, ZHANG J X, et al.Preparation of Reaction-bonded Silicon Carbide with Well Controlled Structure by Tape Casting Method[J]. Ceramics International, 2012, 38(3): 2125-2128.
[19]WANG J, LIN M, XU Z, et al. Microstructure and Mechanical Properties of C/C-SiC Composites Fabricated by a Rapid Processing Method[J]. Journal of the European Ceramic Society, 2009, 29(14): 3091-3097.
[20]冯岩. 碳化硅复合陶瓷耐磨性能研究[J].材料开发与应用, 2017, 32(3):22-26.
FENG Yan. Study on Wear Resistance of Silicon Carbide Composite Ceramics[J]. Development and Application of Materials, 2017, 32(3):22-26.
[21]周松青, 肖汉宁. 碳化硅陶瓷摩擦化学磨损机理及磨损图的研究[J]. 硅酸盐学报, 2002,30(5):641-644.
ZHOU Songqing, XIAO Hanning. Study on Tribochemical Wear Mechanism and Wear Diagram of Silicon Carbide Ceramics[J]. Journal of the Chinese Ceramic Society, 2002,30(5):641-644.
[22]吴玲. 制动用C/C-SiC复合材料摩擦学性能研究现状[J]. 材料导报, 2014, 28(13):52-55.
WU Ling. Research Status of Tribological Properties of C/C-SiC Composites for Braking[J]. Materials Review, 2014, 28(13):52-55.
[23]丁雨田, 戴雷, 尹建军, 等.铝合金表面Ni-SiC复合镀层的摩擦磨损性能[J]. 机械工程学报, 2004,42(3):173-177.
DING Yutian, DAI Lei, YIN Jianjun, et. al. Friction and Wear Properties of Ni-SiC Composite Coating on Aluminum Alloy Surface[J]. Journal of Mechanical Engineering, 2004,42(3):173-177.
[24]李双. 短纤维增强反应烧结碳化硅的制备与性能研究[D]. 哈尔滨:哈尔滨工业大学, 2013.
LI Shuang. Preparation and Properties of Short Fiber Reinforced Reaction Sintered Silicon Carbide[D]. Harbin :Harbin Institute of Technology,2013.
[25]KRENKEL W, BERNDT F. C/C-SiC Composites for Space Applications and Advanced Friction Systems [J]. Materials Science and Engineering: A, 2005, 412(1/2): 177-181.