基于非线性拓扑优化的汽车变厚度保险杠耐撞性设计

中国机械工程

基于非线性拓扑优化的汽车变厚度保险杠耐撞性设计

杨江林1;张诗阳2

1.湖南大学汽车车身先进设计制造国家重点实验室，长沙,410082
2.湖南第一师范学院教育科学学院，长沙,410205

出版日期:2017-09-10 发布日期:2017-09-07
基金资助:
国家自然科学基金资助项目(51575172)
National Natural Science Foundation of China （No. 51575172）

Crashworthiness Design of Bumper Beam Structure with Tailor Rolled Using Nonlinear Topology Optimization Method

YANG Jianglin1;ZHANG Shiyang2

1.State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha, 410082
2.College of Educational Science, Hunan First Normal University, Changsha, 410205

Online:2017-09-10 Published:2017-09-07
Supported by:
National Natural Science Foundation of China （No. 51575172）

摘要/Abstract

摘要： 结合非线性拓扑优化方法和连续变厚度轧制技术对汽车保险杠横梁进行了耐撞性设计。推导了基于板壳厚度插值的非线性吸能灵敏度公式，并把灵敏度约束在轴向与周向上。应用该方法对三点弯工况下的保险杠进行优化设计，最终确定了保险杠的厚度分布。优化结果表明，等质量情况下，对比均匀厚度的保险杠，具有连续变厚度（TRB）结构的保险杠吸收能量值平均提升了近30%。

关键词: 保险杠, 耐撞性, 变厚度板, 拓扑优化, 非线性的

Abstract: The crashworthiness of automotive bumper beams was designed with the TRB rolling manufacturing processes by nonlinear topology optimization. For shell structures, the nonlinear sensitivity formulas of energy absorbing were given based on the thickness interpolation. The sensitivity was constrained in both of axial and circumferential directions. The utilization of this method optimized the bumper beams under three-point bending conditions and the thickness distributions of bumper beams were determined. Compared with that of the uniform thickness structure, the crashworthiness of varied thickness structures is found to enhance averagely by nearly 30% under the same mass conditions.

Key words: bumper beam, crashworthiness, tailor-rolled blank(TRB), topology optimization, nonlinear

中图分类号:

U461.91

杨江林1;张诗阳2. 基于非线性拓扑优化的汽车变厚度保险杠耐撞性设计[J]. 中国机械工程.

YANG Jianglin1;ZHANG Shiyang2 . Crashworthiness Design of Bumper Beam Structure with Tailor Rolled Using Nonlinear Topology Optimization Method[J]. China Mechanical Engineering.

参考文献

[1]钟志华, 张维刚. 汽车碰撞安全技术[M]. 北京: 机械工业出版社,2005.
ZHONG Zhihua, ZHANG Weigang. Automotive Crash Safety Technology[M]. Beijing: China Machine Press,2005.

[2]杜继涛. TRB轧制建模及其在汽车覆盖件上应用的关键技术 [D]. 上海: 同济大学,2008.
DU Jitao. TRB Rolling Modeling and Its Key Technologies in Automotive Panel Applications [D]. Shanghai: Tongji University,2008.

[3]张勇, 李光耀, 孙光永, 等. 多学科设计优化在整车轻量化设计中的应用研究[J]. 中国机械工程,2008,19(7):877-881.
ZHANG Yong, LI Guangyao, SUN Guangyong, et al. Application Research on Multidisciplinary Design Optimization of the Full Vehical Lightweight[J]. China Mechanical Engineering,2008,19(7):877-881.

[4]丁晓明，吕俊成，王伟. 基于典型工况的汽车后桥壳结构轻量化优化设计[J]. 中国机械工程,2016,27(8):1047-1052.
DING Xiaoming, LYU Juncheng, WANG Wei. Light Weight Design of Automobile Rear Axle Housing Based on Typical Conditions[J]. China Mechanical Engineering,2016,27(8):1047-1052.

[5]胡朝辉，张健，李光耀，等. 基于区间分隔的卡车车架轻量化设计[J]. 中国机械工程,2016,27(8):1130-1135.
HU Zhaohui, ZHANG Jian, LI Guangyao, et al. Lightweight Design of a Truck Frame Based on Intervals[J]. China Mechanical Engineering,2016,27(8):1130-1135.

[6]马军伟, 张渝, 丁波. 基于TRB结构的汽车前纵梁轻量化设计[J]. 汽车零部件,2015(3):21-23.
MA Junwei, ZHANG Yu, DING Bo. Lightweight Design of Automotive Front Rail Based on Tailor Rolled Blank Structure[J]. Automobile Parts,2015(3):21-23.

[7]CUANG C H, YANG R J, LI G, et al. Multidisciplinary Design Optimization on Vehicle Tailor Rolled Blank Design[J]. Structural and Multidisciplinary Optimization,2008,35(6):551-560.

[8]HUANG X, XIE Y M, LU G. Topology Optimization of Energy-absorbing Structures [J]. International Journal of Crashworthiness,2007,12(6):663-675.

[9]聂昕, 黄鹏冲, 陈涛, 等. 基于耐撞性拓扑优化的汽车关键安全件设计[J]. 中国机械工程,2013,24(23):3260-3265.
NIE Xin, HUANG Pengchong, CHEN Tao, et al. Topology Optimization of Automotive Key Safety Component Design Based on Crashworthiness[J]. China Mechanical Engineering,2013,24(23):3260-3265.

[10]高云凯, 张玉婷, 方剑光. 基于混合元胞自动机的铝合金保险杠横梁设计[J]. 同济大学学报(自然科学版),2015,43(3):456-461.
GAO Yunkai, ZHANG Yuting, FANG Jianguang. Design of an Aluminum Bumper Beam Based on Hybrid Cellular Automata[J]. Journal of Tongji University(Natural Science),2015,43(3):456-461.

[11]曹立波, 宋慧斌, 武和全, 等. 基于拓扑优化的汽车前纵梁耐撞性设计[J]. 中国机械工程,2016,27(6):827-832.
CAO Libo, SONG Huibin, WU Hequan, et al. Crashworthiness Design of Automotive Front Rail Using Topology Optimization Method[J]. China Mechanical Engineering,2016,27(6):827-832.

[12]SIGMUND O. A. 99 Line Topology Optimization Code Written in MATLAB [J]. Structural and Multidisciplinary Optimization,2001,21(2):120-127.

[1]	赵清海1,2;张洪信2;蒋荣超2;华青松1,2;袁林2. 考虑拓扑相关热载荷的散热结构多相材料拓扑优化设计[J]. 中国机械工程, 2020, 31(20): 2403-2411.
[2]	王冠1；张骞2；寇琳媛1；刘志文3；李世康3. 基于混合元胞自动机算法的连续体结构非线性拓扑优化[J]. 中国机械工程, 2020, 31(18): 2161-2173.
[3]	陈涛1;李宁宁1;李卓1;李奇奇1;陈少伟1;张茜2. 侧面柱碰撞条件下电动汽车电池系统结构优化[J]. 中国机械工程, 2020, 31(09): 1021-1030.
[4]	宋小春;文辉;涂君;张旭;黄松岭. 变厚度板中水平剪切波的传播特性分析[J]. 中国机械工程, 2020, 31(04): 417-424.
[5]	姚佐平;韦勇;吕俊成;刘昌业;梁永彬. 基于精细化多刚体模型的微型汽车耐撞性研究[J]. 中国机械工程, 2020, 31(03): 352-359,372.
[6]	刘延伟1;朱云学1;林子越1;赵克刚2;黄谢鑫3. 考虑自锁元件动态特性的超越离合器-齿轮系统模型研究[J]. 中国机械工程, 2019, 30(15): 1765-1775.
[7]	王欣；喻豪杰；顾振华；胡伟楠. 计及二阶效应的一种桁架臂几何非线性方法[J]. 中国机械工程, 2019, 30(13): 1540-1544.
[8]	李宇鹏1,2；巴春来1；刘来超3. 采用结构仿生的重型机床立柱的综合优化[J]. 中国机械工程, 2019, 30(13): 1621-1625,1637.
[9]	白中浩;谭雯霄;张林伟;周存文. 基于仿生微圆结构的汽车吸能盒耐撞性分析[J]. 中国机械工程, 2019, 30(11): 1261-1267.
[10]	邹坤;侯亮;卜祥建;方奕凯. 基于工况风险评估的叉车门架多工况拓扑优化[J]. 中国机械工程, 2019, 30(05): 568-577.
[11]	贺红林;夏自强;袁维东. 基于改进优化准则法的自由阻尼结构动力学拓扑优化[J]. 中国机械工程, 2018, 29(13): 1531-1539.
[12]	张勇;曾意;徐翔;林继铭;赖雄鸣. 环形梯度多胞结构的多工况耐撞性研究[J]. 中国机械工程, 2018, 29(04): 485-492,498.
[13]	许小奎;郭宝峰;金淼. 基于对比度增强抑制灰度的改进优化准则法[J]. 中国机械工程, 2017, 28(24): 2944-2948,2956.
[14]	梁明轩1,2,3;李正刚2;唐任仲1;陈立2;黄川2. 基于柔性多体动力学的机械臂结构优化设计[J]. 中国机械工程, 2017, 28(21): 2562-2566.
[15]	房伟1;全书海1;谭保华2,3;冉斌4;王力1;焦亚田1. 汽车尾气热电转换装置电气拓扑结构优化[J]. 中国机械工程, 2017, 28(21): 2620-2626.