超声塑化注射系统环形间隙的设计与仿真

中国机械工程

超声塑化注射系统环形间隙的设计与仿真

李霞;田海港;张伟伟;张三川

郑州大学机械工程学院，郑州，450001

出版日期:2017-08-10 发布日期:2017-08-07
基金资助:
国家自然科学基金资助项目（51107121）；
河南省高等学校重点科研项目（15A460032,16A460010）
National Natural Science Foundation of China （No. 51107121）

Design and Simulation of Annular Clearances for Ultrasonic Plasticizing Injection Systems

LI Xia;TIAN Haigang;ZHANG Weiwei;ZHANG Sanchuan

School of Mechanical Engineering, Zhengzhou University,Zhengzhou , 450001

Online:2017-08-10 Published:2017-08-07
Supported by:
National Natural Science Foundation of China （No. 51107121）

摘要/Abstract

摘要： 为获得较优的超声塑化注射系统环形间隙，首先进行超声工具头与塑化腔环形间隙的理论研究，获得环形间隙泄漏量和超声工具头摩擦力的理论公式;然后建立超声工具头与塑化腔环形间隙的有限元模型，利用ANSYS CFX模块研究环形间隙的泄漏量和工具头摩擦力的理论值和仿真值并进行比较，分析环形间隙大小与入口总压力对泄漏量和工具头摩擦力的影响规律。研究结果表明，当超声工具头与塑化腔之间的环形间隙为0.1～0.15mm、入口总压力为10～20MPa时，环形间隙的泄漏量和工具头摩擦力都较小。

关键词: 超声塑化, 环形间隙, 泄漏量, 工具头摩擦力

Abstract: In order to obtain the optimal annular clearance sizes of ultrasonic plasticizing injection systems, a theoretical study of annular clearances of ultrasonic tool heads and plasticizing cavities were proceeded, the theoretical formula of annular clearance leakages and frictions of ultrasonic tool head were acquired. Then annular clearance finite element models of ultrasonic tool heads and plasticizing cavities was established, the theoretical values and simulation values of annular clearance leakages and tool head frictions were studied and compared by mean of ANSYS CFX module, and the influence laws of annular clearance sizes and inlet total pressures on leakages and frictions of tool head were analyzed. The results show that annular clearances of ultrasonic tool head and plasticizing cavities are as 0.10~0.15mm, total pressures of inlet is 10~20MPa, leakages of annular clearances and frictions of tool head are smaller.

Key words: ultrasonic plasticizing, annular clearance, leakage, tool head friction

中图分类号:

TQ320.5

李霞;田海港;张伟伟;张三川. 超声塑化注射系统环形间隙的设计与仿真[J]. 中国机械工程.

LI Xia;TIAN Haigang;ZHANG Weiwei;ZHANG Sanchuan. Design and Simulation of Annular Clearances for Ultrasonic Plasticizing Injection Systems[J]. China Mechanical Engineering.

参考文献

[1]贾娟娟.注塑螺杆的结构设计及塑化过程数值模拟研究[D].西安:陕西科技大学,2009.
JIA Juanjuan. Structure Design and Plasticization Process Numerical Simulation of the Injection Screw [D].Xi'an: Shaanxi University of Science & Technology,2009.

[2]蒋俊,郭媛,曾良才,等.间隙密封液压缸泄漏量仿真分析[J].润滑与密封,2013(7):75-79.
JIANG Jun, GUO Yuan, ZENG Liangcai, et al. Simulation and Analysis of Leakage for Clearance Seal of Hydraulic Cylinder [J].Lubrication Engineering,2013(7):75-79.

[3]周梓荣,彭浩舸,曾曙林.环形间隙中泄漏流量的影响因素研究[J].润滑与密封，2005(1):7-9.
ZHOU Zirong, PENG Haoke, ZENG Shulin. Research on the Influence Factor of Leakage in Annular Clearance Seals[J].Lubrication Engineering,2005(1):7-9.

[4]周梓荣,李夕兵,刘迎春. 环形缝隙中压力水的流动规律研究与实验 [J].中国机械工程,2005,16(11):1008-1012.
ZHOU Zirong, LI Xibing, LIU Yingchun. Study and Experiment on Flow Behavior of Pressurized-water in Annular Micro-gaps [J] China Mechanical Engineering,2005,16(11):1008-1012.

[5]徐林.湍流工况下泵的环状间隙密封内流场分析及泄漏量计算[J].水泵技术,2002(2):17-20.
XU Lin. Analysis of Flow Field in the Annular Clearance of Pump and Calculated Leakage in Turbulent Flow Condition[J].Pump Technology,2002(2):17-20.

[6]侯煜.基于CFD环形间隙泄漏量及其摩擦力的仿真计算[D].太原:太原理工大学,2007.
HOU Yu.Simulation and Calculation of Annular Gap's Leakage and Friction Based on CFD [D].Taiyuan: Taiyuan University of Technology,2007.

[7]KAZAMA T,SASAKI H,NARITA Y.Simultaneous Temperature Measurements of Bearing and Seal Parts of a Swash Plate Type Axial Piston Pump—effects of Piston Clearance and Fluid Property[J]. Journal of Mechanical Science & Technology,2010,24(1):203-206.

[8]高雨,傅连东,湛从昌,等.液压缸活塞变间隙密封结构形状研究 [J].中国机械工程,2016,27(24):3345-3350.
GAO Yu, FU Liandong, ZHAN Congchang, et al. Research on Piston Variable Clearance Sealing Structure Shape in Hydraulic Cylinders [J]. China Mechanical Engineering, 2016,27(24):3345-3350.

[9]杨秀峰.水压环形缝隙泄漏特性的理论和实验研究[D].武汉:华中科技大学,2012.
YANG Xiufeng. Theoretical and Experimental Research on Leakage Characteristics of Water Hydraulic Annular Clearance[D].Wuhan: Huazhong University of Science and Technology,2012.

[10]刘春太,陈静波,王利霞，等.注射成型过程中非牛顿塑料熔体的粘度模型[J].中国塑料,1997,11(1):48-52.
LIU Chuntai, CHEN Jingbo, WANG Lixia, et al. The Viscosity Model of Non-Newtonian Plastics Melt in Injection Molding [J].China Plastics,1997,11(1):48-52.

[11]CHIANG H H, HIEBER C A, WANG K K. A Unified Simulation of the Filling and Post filling Stages in Injection Molding. Part I: Formulation [J].Polymer Engineering and Science,1991,31(2):116 -124.

[12]赵怀学.超声波辅助精密微注塑机理及应用研究[D].天津:天津大学,2011.
ZHAO Huaixue. Study on Mechanism and Application in Precision Injection Molding of Microstructures Assisted by Ultrasonic[D]. Tianjin: Tianjin University,2011.

[13]王国志,李玉辉,吴文海,等.变形对轴向柱塞泵柱塞副泄漏量的影响研究[J].机床与液压,2011,39(17):50-52.
WANG Guozhi, LI Yuhui, WU Wenhai, et al. Influence of Deformation on Leakage of Piston and Cylinder in Axial Piston Pump[J].Machine Tool and Hydraulics,2011,39(17):50-52.

[14]曾曙林,周梓荣,尹久仁.水压环形缝隙泄漏量的实验研究[J].机床与液压,2003(2):169-171.
ZENG Shulin, ZHOU Zirong, YIN Jiuren. A Leakage Testing Research for Annular Gap under Water Hydraulic Pressure [J].Machine Tool and Hydraulics,2003(2):169-171.