基于等切共轭的弧齿锥齿轮差曲面建立与解析

摘要/Abstract

摘要： 对弧齿锥齿轮提出了一种新的共轭求解方法，来更方便地求解共轭小轮的齿面方程，在此基础上进行了齿面接触分析。在分析过程中提出了一种新的ease-off差曲面计算方法，即用对应点的转角误差替代直线误差进行差曲面求解，使得传动误差解析、齿面修形量的确定更为直观和准确。提取了ease-off曲面上的差曲线，以方便地确定出接触路径和边缘接触点。根据全程差曲线得到了齿面接触印痕分布情况。

关键词: 齿面接触分析, 等切共轭, 差曲面, 传动误差, 差曲线

Abstract: A novel conjugate method for spiral bevel gears was proposed, which was more convenient to solve the tooth surface equation of conjugate pinion. Then, the tooth contact analysis was carried out. In the analysis processes, a new ease-off difference surface calculation method was proposed, which used angle errors of the corresponding points instead of straight-line errors to obtain difference surface. Difference curve on ease-off surface was extracted, which might easily determine the contact path and edge contact points. According to the whole difference curve, the distribution of contact marks on the tooth surfaces was obtained.

Key words: tooth contact analysis, common tangent conjugation, ease-off surface, transmission error, difference curve

中图分类号:

TH132.4

张波;魏冰阳;刘大可. 基于等切共轭的弧齿锥齿轮差曲面建立与解析[J]. 中国机械工程.

ZHANG Bo;WEI Bingyang;LIU Dake. Construction and Analysis of Spiral Bevel Gear Ease-off Surfaces Based on Common Tangent Conjugation[J]. China Mechanical Engineering.

参考文献

[1]LITVIN F L, FUENTES A. Gear Geometry and Applied Theory[M]. New York: Cambridge University Press, 2004.

[2]KOLIVAND M, KAHRAMAN A. An Ease-off Based Method for Loaded Tooth Contact Analysis of Hypoid Gears Having Local and Global Surface Deviations[J]. Journal of Mechanical Design, 2009,132(7):245-254.

[3]聂少武, 邓静, 邓效忠, 等. 基于齿面Ease off拓扑的弧齿锥齿轮齿面偏差等效修正方法[J]. 中国机械工程, 2017,28(20):2434-2440.

NIE Shaowu, DENG Jing, DENG Xiaozhong, et al. Tooth Surface Error Equivalent Correction Method of Spiral Bevel Gears Based on Ease off Topology[J]. China Mechanical Engineering, 2017,28(20):2434-2440.

[4]魏冰阳, 杨建军, 仝昂鑫, 等. 基于等距Ease-off曲面的轮齿啮合仿真分析[J]. 航空动力学报, 2017,32(5):1259-1265.

WEI Bingyang, YANG Jianjun, TONG Angxin, et al. Tooth Meshing Simulation and Analysis Based on Isometric Mapping Ease-off Surface[J]. Journal of Aerospace Power, 2017,32(5):1259-1265.

[5]DING H, TANG J, ZHOU Y, et al. A Multi-objective Correction of Machine Settings Considering Loaded Tooth Contact Performance in Spiral Bevel Gears by Nonlinear Interval Number Optimization[J]. Mechanism & Machine Theory, 2017,113:85-108.

[6]DING H, WAN G, ZHOU Y, et al. Nonlinearity Analysis Based Algorithm for Identifying Machine Settings in the Tooth Flank Topography Correction for Hypoid Gears[J]. Mechanism & Machine Theory, 2017,113:1-21.

[7]SHIH Y P, CHEN S D. Free-form Flank Correction in Helical Gear Grinding Using a Five-axis Computer Numerical Control Gear Profile Grinding Machine[J]. Journal of Manufacturing Science & Engineering, 2012,134(4):41006.

[8]吴序堂. 齿轮啮合原理[M]. 西安: 西安交通大学出版社, 2009.

WU Xutang. Gear Meshing Principle[M]. Xian: Xian Jiaotong University Press, 2009.

[9]曾韬. 螺旋锥齿轮设计与加工[M]. 哈尔滨: 哈尔滨工业大学出版社, 1989.

ZENG Tao. Design and Processing of Spiral Bevel Gear[M]. Harbin: Harbin Institute of Technology Press, 1989.

[10]郑昌启. 弧齿锥齿轮和准双曲面齿轮[M]. 北京: 机械工业出版社, 1988.

ZHENG Changqi. Spiral Bevel Gear and Hypoid Gear[M]. Beijing: China Machine Press, 1988.

[11]熊禾根. 机械传动系统Romax Designer建模、分析及应用[M]. 武汉：华中科技大学出版社, 2015.

XIONG Hegen. Modeling, Analysis and Application of Mechanical Transmission System Romax Designer[M]. Wuhan:Huazhong University of Science and Technology Press, 2015.

[1]	白亚莉1;张毅1;冀敏2;刘文强3. 基于多分布响应面算法的火炮方向机齿轮传动误差可靠性分析[J]. 中国机械工程, 2017, 28(13): 1593-1600.
[2]	雷贤卿, 孟琦, 马文锁, 杨科林. 闭环齿轮传动系统传动误差研究[J]. 中国机械工程, 2017, 28(06): 675-682.
[3]	雷贤卿, 蔡振华, 张明柱, 马文锁. 液压机械无级变速器机械变速机构的传动误差分析[J]. 中国机械工程, 2015, 26(23): 3253-3259.
[4]	雷敦财, 唐进元. 一种面齿轮传动时变啮合刚度数值计算方法[J]. 中国机械工程, 2014, 25(17): 2300-2304.
[5]	张靖1, 陈兵奎1, 吴长鸿2, 李朝阳1, 3. 圆锥滚子轴承预紧力对变速器啸叫噪声的影响分析[J]. 中国机械工程, 2013, 24(11): 1453-1458.
[6]	彭东林1, 2, 郑永1, 陈自然1, 高忠华2, 郑方燕2. 基于时栅传感器的传动误差动态测试系统研制 [J]. 中国机械工程, 2011, 22(10): 1138-1142.
[7]	郑永, 彭东林, 王先全, 杨继森, 陈自然. 新型蜗轮副综合参数检查仪研制及精度检定 [J]. 中国机械工程, 2010, 21(24): 2989-2994.
[8]	唐进元, 雷国伟. CNC机床运动误差对弧齿锥齿轮齿面接触质量的影响研究 [J]. 中国机械工程, 2010, 21(20): 2395-2401,2429.
[9]	徐恺, 邓效忠, 刘更, 杨建军, 苏建新. 含有直廓内齿轮行星轮系的传动误差计算与噪声试验 [J]. 中国机械工程, 2010, 21(1): 76-79.
[10]	王成;方宗德;贾海涛;吉强;. 修形人字齿轮传动误差计算与试验研究[J]. J4, 2009, 20(20): 0-2398.
[11]	周凯红;;唐进元;严宏志;. 摇台磨齿机与Free—form型数控磨齿机加工调整参数转换的运动分析法[J]. J4, 2009, 20(11): 0-1269.
[12]	唐进元;杜晋;. 考虑安装误差敏感性的螺旋锥齿轮主动设计方法[J]. J4, 2009, 20(10): 0-1175.
[13]	华林;黄海浪;韩星会;冯玮;. 渐开线直齿圆锥齿轮齿廓圆弧修形方法研究 [J]. J4, 2009, 20(07): 0-881.
[14]	陈书涵;严宏志;明兴祖;钟掘;谢耀东;. 螺旋锥齿轮误差齿面及差曲面的建立与分析[J]. J4, 2008, 19(18): 0-2151.
[15]	邓效忠, 杨建军, 魏冰阳, 方宗德. 超声激励下弧齿锥齿轮研齿系统动态研磨力分析[J]. 中国机械工程, 2007, 18(19): 2359-2361.