类金刚石膜在水环境下的摩擦学行为

中国机械工程

类金刚石膜在水环境下的摩擦学行为

郭飞飞1;金守峰1;秦立果2;董光能2

1.西安工程大学机电工程学院，西安，710048
2.西安交通大学机械工程学院，西安，710049

出版日期:2019-09-25 发布日期:2019-09-24
基金资助:
陕西省自然科学基础研究项目(2018JQ5171）；
西安工程大学博士科研启动基金资助项目(BS1701）

Tribological Behavior of DLC Films under Water Environment

GUO Feifei1;JIN Shoufeng1;QIN Liguo2;DONG Guangneng2

1.College of Mechanical and Electrical Engineering,Xi'an Polytechnic University,Xi'an,710048
2.College of Mechanical Engineering,Xi'an Jiaotong University,Xi'an,710049

Online:2019-09-25 Published:2019-09-24

摘要/Abstract

摘要： 测试了 CoCrMo合金表面沉积类金刚石薄膜与CoCrMo在水溶液润滑下的摩擦磨损行为。结果表明：摩擦副在不同浓度牛血清白蛋白溶液润滑下的平均摩擦因数均在0.10左右，CoCrMo合金销磨损量最小值为1.69×10-5 mm3；相同条件下，生理盐水溶液润滑的磨损量为1.38×10-5 mm3，且销表面有转移膜生成；牛血清白蛋白溶液润滑时，界面蛋白吸附层屏蔽了转移膜的形成。根据结果可知，转移膜的形成经历了磨屑附着、连续转移、局部脱落的过程。

关键词: CoCrMo合金, 类金刚石膜, 摩擦, 磨损, 润滑

Abstract: Tribological behavior of the DLC films was analyzed systematically, which were deposited on the polished surfaces of CoCrMo alloy with respect to the CoCrMo under the lubrication of aqueous solution. Results show that the average friction coefficient is about 0.10 under bovine serum albumin (BSA) solution lubrication with different concentrations,and the smallest wear loss of CoCrMo pin is about 1.69×10-5 mm3. In the same conditions, the wear loss of CoCrMo pins under the lubrication of physiological saline solution is 1.38×10-5 mm3. The DLC transfer layer exists on the wear scar lubricated with physiological saline solution. It indicates that the formation of DLC transfer layer is inhibited by the adsorption of bovine serum albumin protein layer. The formation of transfer layer has undergone the processes of wear debris adhesion, continuous transferring, and partial delamination.

Key words: CoCrMo alloy, diamond-like carbon(DLC) film, friction, wear, lubrication

中图分类号:

TH117

郭飞飞1;金守峰1;秦立果2;董光能2. 类金刚石膜在水环境下的摩擦学行为[J]. 中国机械工程.

GUO Feifei1;JIN Shoufeng1;QIN Liguo2;DONG Guangneng2. Tribological Behavior of DLC Films under Water Environment[J]. China Mechanical Engineering.

参考文献

[1]HAERI M, GILBERT J L. Study of Cellular Dynamics on Polarized CoCrMo Alloy Using Time-lapse Live-cell Imaging[J]. Acta Biomaterialia, 2013, 9(11) ：9220-9228.
[2]席翔, 夏延秋, 曹正锋, 等. 高速电弧喷涂Al-Ni-Mm-Co涂层在脂润滑下的摩擦磨损性能[J]. 中国机械工程, 2017, 28(2)：215-222.
XI Xiang, XIA Yanqiu, CAO Zhengfeng, et al. Tribology Performance of High Speed Arc Spraying Al-Ni-M-Co Film under Lubrication Condition of Different Greases[J]. China Mechanical Engineering, 2017, 28(2)：215-222.
[3]BALAGNA C, AGA M G, SPRIANO S. Tantalum-based Multilayer Film on Cobalt Alloys in Total Hip and Knee Replacement[J]. Materials Science and Engineering C, 2012, 32 (4)：887-895.
[4]LIU H, LENG Y, TANG J, et al. Tribological Performance of Ultra-high-molecular-weight Polyethylene Sliding against DLC-coated and Nitrogen Ion Implanted CoCrMo Alloy Measured in a Hip Joint Simulator[J]. Surface and Coatings Technology, 2012, 206 (23)：4907-4914.
[5]GALETZ M C, SEIFERTH S H, THEILE B, et al. Potential for Adhesive Wear in Friction Couples of UHMWPE Running against Oxidized Zirconium, Titanium Nitride Films, and Cobalt-chromium Alloys[J]. Journal of Biomedical Materials Ressearch, 2010, 93B(2)：468-475.
[6]VITU T, ESCUDEIRO A, Polcar T, et al. Sliding Properties of Zr-DLC Film：the Effect of Tribolayer Formation[J]. Surface & Film Technology, 2014, 258： 734-745.
[7]CHO Y K, JANG W S, YOO S, et al. Synthesis of Conductive Ti-C:H Films on the Stainless Steel Plates by PECVD Process[J]. Surface & Films Technology, 2008, 202 (22/23)：5390-5394.
[8]VENGUDUSAMY B, GRAFL A, PREINFALK K. Tribological Properties of Hydrogenated Amorphous Carbon under Dry and Lubricated Conditions[J]. Diamond & Related Materials, 2014, 41：53-64.
[9]SUTTON D C, LIMBERT G, STEWART D, et al. The Friction of Diamond-like Carbon Films in a Water Environment[J]. Friction, 2013, 1 (3)：210-221.
[10]DUONG C T, LEE J H, CHO Y, et al. Effect of Protein Concentrations of Bovine Serum Albumin and γ-globulin on the Frictional Response of a Cobalt-chromium Femoral Head[J]. Journal of Materials Science Materials in Medicine, 2012, 23(5)：1323-1330.
[11]LAUX K A, SCHWARTZ C J. Influence of Linear Reciprocating and Multi-directional Sliding on PEEK Wear Performance and Transfer Film Formation[J]. Wear, 2013, 301：727-734.

[1]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[2]	方远方, 张华. 铝合金型材的静轴肩倾斜搅拌摩擦焊接头性能[J]. 中国机械工程, 2021, 32(07): 815-820.
[3]	李永康1，2;王军1;廉自生1，2. 混合润滑条件下的斯特封高速摩擦与密封特性[J]. 中国机械工程, 2021, 32(05): 533-539.
[4]	孔晓瑶1,2;袁松梅1,2;朱光远1,2;张文杰1,2. 微量润滑系统参数对雾化特性的影响[J]. 中国机械工程, 2021, 32(05): 579-586.
[5]	唐斌, 范志勇, 项载毓, 吴元科, 黄博, 莫继良, . [轮轨磨耗及预测]高速列车制动摩擦块切入端特征对制动界面特性的影响[J]. 中国机械工程, 2021, 32(04): 412-419.
[6]	王志强, 雷震宇, . [轮轨磨耗及预测]地铁直线轨道钢轨波磨影响参数研究[J]. 中国机械工程, 2021, 32(04): 420-430.
[7]	王瑞1；贾谦1,2；袁小阳1. 石墨水润滑动压推力轴承的起飞转速及磨损的量化研究[J]. 中国机械工程, 2021, 32(03): 269-274.
[8]	张磊1;刘武军3;解社娟1,4;王小刚2;孔玉莹2;马强2;陈振茂1. 核电站指套管磨损缺陷的扫频涡流检测及创新型特征提取[J]. 中国机械工程, 2021, 32(01): 18-25.
[9]	吴玉厚;张珈翊;张丽秀;王俊海. 旋转滑动摩擦副摩擦噪声影响因素实验研究[J]. 中国机械工程, 2020, 31(23): 2814-2821.
[10]	王志刚, 吉川泰晴, 董文正, . [成形过程仿真优化与集成计算材料工程]塑性加工摩擦定律的研究进展[J]. 中国机械工程, 2020, 31(22): 2708-2714.
[11]	李迎春1，2;程蓓1;邱明1，2;谷守旭1;范恒华1. 不同石墨烯添加量下MoS2基复合涂层的摩擦磨损及耐腐蚀性能[J]. 中国机械工程, 2020, 31(20): 2437-2444.
[12]	李蓉蓉;尹延国;张开源;曾庆勤 ;陈奇. 机械合金化FeS/Cu复合材料的摩擦磨损性能[J]. 中国机械工程, 2020, 31(17): 2024-2030.
[13]	戴稳1;张超勇1;孟磊磊1;薛燕社1;肖鹏飞1;尹勇2. 采用深度学习的铣刀磨损状态预测模型[J]. 中国机械工程, 2020, 31(17): 2071-2078.
[14]	陈永亮1; 杨子超1;林恒利1;崔雷2;宋建岭3;王东坡2 . 拉锻式摩擦塞焊的热力耦合解析模型和试验验证[J]. 中国机械工程, 2020, 31(17): 2118-2127.
[15]	徐鲁帅1;王赟磊1;张帆1;郝木明2;袁小阳1. 螺旋槽机械密封瞬态启动过程润滑特性[J]. 中国机械工程, 2020, 31(16): 1891-1900.