搅拌摩擦焊和热处理复合工艺对2219铝合金组织性能的影响

中国机械工程

搅拌摩擦焊和热处理复合工艺对2219铝合金组织性能的影响

李小霞1，2;黄亮1，2;李建军1，2;王泽宇1，2

1.华中科技大学材料科学与工程学院,武汉，430074
2.华中科技大学材料成形与模具技术国家重点实验室，武汉,430074

出版日期:2017-12-10 发布日期:2017-12-08
基金资助:
国家自然科学基金资助项目（51575206）；
国家重点基础研究发展计划（973计划）资助项目（2011CB012802）；
中国航天科技集团公司航天科技创新基金资助项目(CASC150704)；
中央高校基本科研业务费专项资金资助项目（2016YXZD055）
National Natural Science Foundation of China （No. 51575206）
National Basic Research Program (973 Program) （No. 2011CB012802）
Fundamental Research Funds for the Central Universities（No. 2016YXZD055）

Effects of Compound Technology of FSW and Heat Treatment on Microstructures and Properties of 2219 Aluminum Alloys

LI Xiaoxia1，2;HUANG Liang1，2;LI Jianjun1，2;WANG Zeyu1，2

1.School of Materials Science and Engineering,Huazhong University of Science and Technology, Wuhan,430074
2.State Key Laboratory of Materials Processing and Die & Mould Technology,Huazhong University of Science and Technology,Wuhan,430074

Online:2017-12-10 Published:2017-12-08
Supported by:
National Natural Science Foundation of China （No. 51575206）
National Basic Research Program (973 Program) （No. 2011CB012802）
Fundamental Research Funds for the Central Universities（No. 2016YXZD055）

摘要/Abstract

摘要： 研究了不同时效温度和时间对2219铝合金组织性能的影响，对比了搅拌摩擦焊-固溶-时效、固溶-搅拌摩擦焊-时效、固溶-时效-搅拌摩擦焊这三种复合工艺所得2219铝合金的力学性能。结果表明，2219铝合金最佳时效工艺是180℃/6h，其抗拉强度为386MPa，断后延伸率为24.8%，该工艺所得微观组织中晶界上没有位错和第二相粒子，晶内弥散着细小的θ″相。最佳复合工艺方案为搅拌摩擦焊-固溶-时效，所得2219铝合金抗拉强度为380MPa，断后延伸率为15.4%。该工艺所得焊缝组织晶粒异常长大，薄弱区为热影响区，单向拉伸所得断口的韧窝较大较深，底部存在着第二相粒子。

关键词: 2219铝合金, 热处理, 搅拌摩擦焊, 组织性能, 析出相

Abstract: The effects on microstructures and properties of 2219 aluminum alloys under different aging temperatures and time were investigated. According to the mechanics properties of 2219 aluminum alloys, three compound technologies were compared, including FSW-solid solution-aging, solid solution-FSW-aging and solid solution-aging-FSW. The results show that the tensile strength and elongation rate of the alloys are as 386MPa and 24.8% respectively after aging at 180℃/6h. It is also found that the very fine θ″ precipitates appear inside the grains, no second phases and dislocation on grain boundaries. The best mechanics properties of 2219 aluminum alloys are achieved by the compound technology of FSW-solid solution-aging, the tensile strength and elongation rate of the alloys are as 380MPa and 15.4% respectively. The abnormal growth of grains is found in the joints, and the heat affected zones in the FSW joints are the weak areas of mechanics property. It is also found that the dimples on tensile fracture are more lager and deeper, and second-phase particles appear at the bottom.

Key words: 2219 aluminum alloy, heat treatment, friction stir welding(FSW), microstructure and property, precipitate

中图分类号:

TG166.3
TG44

李小霞1，2;黄亮1，2;李建军1，2;王泽宇1，2. 搅拌摩擦焊和热处理复合工艺对2219铝合金组织性能的影响[J]. 中国机械工程.

LI Xiaoxia1，2;HUANG Liang1，2;LI Jianjun1，2;WANG Zeyu1，2. Effects of Compound Technology of FSW and Heat Treatment on Microstructures and Properties of 2219 Aluminum Alloys[J]. China Mechanical Engineering.

参考文献

[1]李湘宁, 刘宇. 重型运载火箭动力系统分析[J]. 航空动力学报,2010,25(1):180-186.
LI Xiangning, LIU Yu. Basic Parameters Analysis of First Stage Engine System for Heavy Lift Vehicle[J]. Journal of Aerospace Power,2010,25(1):180-186.
[2]刘文芝, 张春林, 张乃仁, 等. 固体火箭发动机推力向量控制系统动态性能分析[J]. 中国机械工程,2007,18(12):1404-1408.
LIU Wenzhi, ZHANG Chunlin, ZHANG Nairen, et al. Dynamic Characteristics Analysis of Solid Propellant Rocket Motor Thrust Vector Control System[J]. China Mechanical Engineering,2007,18(12):1404-1408.
[3]佚名.神箭飞天——“长征”系列运载火箭[J].军事文摘,2016(22):16-19.
Anon. Flying Arrows—— “Long March” Series Launch Vehicle [J]. Military Dugest,2016(22):16-19.
[4]佚名.回顾长征火箭辉煌历史共启中国航天创新篇章——我国长征系列运载火箭实现200次发射[J]. 卫星与网络,2014(12):38-40.
Anon. Magnificent History Review of the Long March Rocket Altogether and China Aerospace Innovation Chapter-China's Long March Rockets Achieve 200 Launch[J]. Satellite & Network,2014(12):38-40.
[5]KAIBYSHEV R, SITDIKOV O, MAZURINA I, et al. Deformation Behavior of a 2219 Al Alloy[J]. Materials Science and Engineering: A,2002,334(1):104-113.
[6]NARAYANA G V, SHARMA V M J,DIWAKAR V, et al. Fracture Behaviour of Aluminium Alloy 2219-T87 Welded Plates[J]. Science and Technology of Welding & Joining,2004,9(2):121-130.
[7]KAIBYSHEV R, KAZAKULOV I, GROMOV D, et al. Superplasticity in a 2219 Aluminum Alloy[J]. Scripta Materialia,2001,44(10):2411-2417.
[8]NI Z, ZHAO H, MI P, et al. Microstructure and Mechanical Performances of Ultrasonic Spot Welded Al/Cu Joints with Al 2219 Alloy Particle Interlayer[J]. Materials & Design,2016,92:779-786.

[9]师春生,张智峰,赵乃勤,等.确定提高2219铝合金性能的变形热处理条件的方法:中国,201310593472.8[P].2014-02-19.
SHI Chunsheng, ZHANG Zhifeng, SHI Naiqin, et al. The Method of Deformation and Heat Treatment to Improve the Performance of 2219 Aluminum: China, 201310593472.8[P]. 2014-02-19.
[10]赵乃勤,刘燕,师春生,等.2219铝合金的时效热处理方法:中国,201310388626.X[P].2013-12-25.
ZHAO Naiqin, LIU Yan, SHI Chunsheng, et al. The Aging Heat Treatment Method of 2219 Aluminum: China, 201310388626.X[P]. 2013-12-25.
[11]陈迎春, 刘会杰, 冯吉才. 2219-O铝合金的搅拌摩擦焊接[J]. 焊接学报,2006,27(1):65-68.
CHEN Yingchun, LIU Huijie, FENG Jicai. Friction Stir Welding of 2219-O Aluminum Alloy[J]. Transactions of the China Welding Institution,2006,27(1):65-68.
[12]王春炎, 曲文卿, 姚君山, 等. 2219-T87 铝合金搅拌摩擦焊接头组织与力学性能[J]. 焊接学报,2010,31(10):77-80.
WANG Chunyan, QU Wenqing, YAO Junshan, et al. Microstructures and Mechanical Properties of Friction Stir Welded 2219-T87 Aluminum Alloy Joints[J]. Transactions of the China Welding Institution,2010,31(10):77-80.
[13]陈华斌, 王继锋, 郑德根, 等. 2219 铝合金搅拌摩擦焊接头弱连接缺陷微观表征及分析[C]//中国机械工程学会焊接学会第十八次全国焊接学术会议论文集——S05 机器人与自动化. 南昌，2013:2-5.
CHEN Huabin, WANG Jifeng, ZHEN Degen, et al. Micro Characteristic and Analysis of the Kiss Bonding Defects of the 2219 Aluminum Alloy in Friction Stir Weld[C]//The 18th National Conference on Welding of Chinese Mechanical Engineering Societiy-S05 Robotics and Automation.Nanchang,2013:2-5.

[14]罗传红, 彭卫平, 张建强, 等. 焊后热处理对 2219-T6 铝合金搅拌摩擦焊接头力学性能的影响[J]. 材料热处理学报,2015,36(3):35-39.
LUO Chuanhong, PENG Weiping, ZHANG Jianqiang, et al. Effect of Post Weld Heat Treatment on Mechanical Properties of Friction Stir Welded Joints for 2219-T6 Aluminum Alloy[J]. Transctions of Materials and Heat Treatment,2015,36(3):35-39.

[15]杜波,孙转平,杨新岐,等. 异种铝合金摩擦塞补焊接头微观组织及性能[J].机械工程学报,2017,53(4):43-48.
DU Bo, SUN Zhuanping, YANG Xinqi, et al. Microstructure and Mechanical Properties of Friction Plug Welding Joints for Dissimilar Aluminum Alloys [J]. Journal of Mechanical Engineering,2017,53(4):43-48.

[16]康举, 李吉超, 冯志操, 等. 2219-T8铝合金搅拌摩擦焊接头力学和应力腐蚀性能薄弱区研究[J]. 金属学报,2016,52(1):60-70.
KANG Ju, LI Jichao, FENG Zhicao, et al. Investigation on Mechanical and Stress Corrosion Carcking Properties of Weakness Zone in Friction Stir Wellded 2219-T8 Al Alloy[J]. Acta Metallurgica Sinica,2016,52(1):60-70

[17]MOTT N F, NABARRO F R N. An Attempt to Estimate the Degree of Precipitation Hardening, with a Simple Model[J]. Proceedings of the Physical Society,1940,52(1):86.

[18]NARAYANA G V, SHARMA V M J, DIWAKAR V, et al. Fracture Behaviour of Aluminium Alloy 2219-T87 Welded Plates[J]. Science and Technology of Welding & Joining,2004,9(2):121-130.
[19]SON S K, TAKEDA M, MITOME M, et al. Precipitation Behavior of an Al-Cu Alloy during Isothermal Aging at Low Temperatures[J]. Materials Letters,2005,59(6):629-632.