基于修正Preston方程的百页轮抛光材料去除深度建模

doi:10.3969/j.issn.1004-132X.2022.22.008

中国机械工程 ›› 2022, Vol. 33 ›› Issue (22): 2711-2716.DOI: 10.3969/j.issn.1004-132X.2022.22.008

基于修正Preston方程的百页轮抛光材料去除深度建模

张军锋1；史耀耀2；蔺小军2；吴晓君1

1.西安建筑科技大学机电工程学院，西安，710055
2.西北工业大学航空发动机高性能制造工业和信息化部重点实验室，西安，710072

出版日期:2022-11-25 发布日期:2022-12-22
作者简介:张军锋，男，1986年生，讲师、博士。研究方向为机电控制及自动化、复杂曲面磨削工艺及机理等。发表论文5篇。E-mail:574836232@qq.com。
基金资助:
陕西省教育厅自然科学专项(20JK0726)

Modeling of Material Removal Depth in ABFW Polishing Based on Modified Preston Equation

ZHANG Junfeng1；SHI Yaoyao2；LIN Xiaojun2；WU Xiaojun1

1.School of Mechanical and Electrical Engineering,Xian University of Architecture and Technology,Xian，710055
2.Key Laboratory of High Performance Manufacturing for Aero Engine,Ministry of Industry and Information Technology,Northwestern Polytechnical University,Xian,710072

Online:2022-11-25 Published:2022-12-22

摘要/Abstract

摘要： 由于百页轮具有一定的柔性，故实际材料去除深度与名义抛光深度不一致，直接影响抛光效率及表面质量的控制。基于Hertz弹性接触理论建立了抛光接触区抛光压力和切削速度分布函数，并依据修正的Preston方程建立了材料去除深度模型，据此确定了影响材料去除深度的关键抛光工艺参数(磨粒粒度、主轴转速、百页轮变形量和进给速度)，获得了百页轮抛光接触区的材料去除深度分布规律和关键抛光工艺参数对材料去除深度的影响规律。最后，通过模拟仿真和抛光实验验证了所建模型和影响规律的正确性，结果表明，该模型可以较好地预测百页轮柔性抛光的材料去除深度。

关键词: 百页轮, 柔性抛光, 材料去除深度, Preston方程

Abstract: Due to the elasticity of ABFW, the actual material removal depth was not consistent with the nominal polishing depth, which directly affected the control of polishing efficiency and surface quality. Based on the Hertz elastic contact theory, the distribution function of polishing pressure and cutting speed in the contact area was established, and the material removal depth model was established according to the modified Preston equation. Based on this, the key processing parameters that affected the material removal depthi.e、abrasive particle size, spindle speed, ABFW deformation and feed rate were determined. Then, the distribution of material removal depth in contact areas and the influences of key polishing process parameters on the material removal depth were obtained. Finally, the correctness of the model and the influence law were verified by simulation and polishing experiments, the results show that the model may better predict the material removal depth of ABFW polishing.

Key words: , abrasive belt flap wheel(ABFW), flexible polishing, material removal depth, Preston equation

中图分类号:

V261.2

张军锋, 史耀耀, 蔺小军, 吴晓君. 基于修正Preston方程的百页轮抛光材料去除深度建模[J]. 中国机械工程, 2022, 33(22): 2711-2716.

ZHANG Junfeng, SHI Yaoyao, LIN Xiaojun, WU Xiaojun. Modeling of Material Removal Depth in ABFW Polishing Based on Modified Preston Equation[J]. China Mechanical Engineering, 2022, 33(22): 2711-2716.

参考文献

［1］段继豪. 整体叶盘构件数控磨削工艺关键技术研究［D］. 西安：西北工业大学, 2016.
DUAN Jihao. Research on the Key Technology of NC Grinding Process for Blisk Structural Components［D］. Xian：Northwestern Polytechnical University, 2016.
［2］淮文博, 史耀耀, 唐虹, 等. 砂布轮抛光叶片表面粗糙度预测与参数优化［J］. 计算机集成制造系统, 2017, 23(12):2708-2718.
HUAI Wenbo, SHI Yaoyao, TANG Hong, et al. Surface Roughness Prediction and Processing Parameters Optimization in Abrasive Cloth Wheel Polishing Process for Blade［J］. Computer Integrated Manufacturing Systems, 2017, 23(12):2708-2718.
［3］ZHANG J F, SHI Y Y, LIN X J, et al. Five-axis Abrasive Belt Flap Wheel Polishing Method for Leading and Trailing Edges of Aero-engine Blade［J］. International Journal of Advanced Manufacturing Technology, 2017, 93(9/12):3383-3393.
［4］CHEN Z, SHI Y Y, LIN X J, et al. Analysis and Optimization of Process Parameter Intervals for Surface Quality in Polishing Ti-6Al-4V Blisk Blade［J］. Results in Physics, 2019, 12:870-877.
［5］XIAN C, SHI Y Y, LIN X J, et al. Force Modeling for Polishing Aero-engine Blades with Abrasive Cloth Wheels［J］. The International Journal of Advanced Manufacturing Technology, 2020, 106(11):5255-5267.
［6］LIU D, SHI Y Y, LIN X J, et al. Polishing Surface Integrity of TC17 Aeroengine Blades［J］. Journal of Mechanical Science and Technology, 2020, 34(2):689-699.
［7］刘德, 史耀耀, 蔺小军, 等. 叶片抛光表面粗糙度与残余应力优化分析［J］.计算机集成制造系统, 2021, 27(5):1328-1340.
LIU De, SHI Yaoyao, LIN Xiaojun, et al. Optimization Analysis of Surface Roughness and Residual Stress of Polished Aero-engine blade［J］. Computer Integrated Manufacturing Systems, 2021, 27(5):1328-1340.
［8］WU S, KAZEROUNIAN K, GAN Z, et al. A Material Removal Model for Robotic Belt Grinding Process［J］. Machining Science and Technology, 2014, 18(1):15-30.
［9］WANG G L, ZHOU X, YANG X, et al. Material Removal Profile for Large Mould Polishing with Coated Abrasives［J］. The International Journal of Advanced Manufacturing Technology, 2015, 80(1/4):625-635.
［10］WANG Y J, HUANG Y, CHEN Y X, et al. Model of an Abrasive Belt Grinding Surface Removal Contour and Its Application［J］. The International Journal of Advanced Manufacturing Technology, 2016, 82(9/12):2113-2122.
［11］FENG D, SUN Y, DU H. Investigations on the Automatic Precision Polishing of Curved Surfaces Using a Five-axis Machining Centre［J］. International Journal of Advanced Manufacturing Technology, 2014, 72(9/12):1625-1637.
［12］SONG J, YAO Y. Material Removal Model Considering Influence of Curvature Radius in Bonnet Polishing Convex Surface［J］. Chinese Journal of Mechanical Engineering, 2015, 28(6):1109-1116.
［13］JIN M, JI S M, LI Z , et al. Material Removal Model and Contact Control of Robotic Gasbag Polishing Technique［C］∥IEEE Conference on Robotics, Automation & Mechatronics. Chengdu, 2008:879-883.
［14］母焰. 恒力砂带磨抛材料去除理论与实验研究［D］. 长春：吉林大学, 2017.
MU Yan. The Theoretical and Experimental Research on the Material Removal of Constant Force Abrasive Belt Grinding and Polishing［D］. Changchun:Jilin University, 2017.
［15］张雷, 袁楚明, 周祖德, 等. 模具曲面抛光时表面去除的建模与试验研究［J］. 机械工程学报, 2002, 38(12):98-102.
ZHANG Lei, YUAN Chuming, ZHOU Zude, et al. Modeling and Experiment of Material Removal in Polishing on Mold Curved Surfaces［J］. Journal of Mechanical Engineering, 2002, 38(12):98-102.
［16］王清辉, 谢柳杰, 许晨旸, 等. 曲面抛光的材料去除模型与摆线轨迹控制［J］. 华南理工大学学报(自然科学版), 2018, 46(3):8-15.
WANG Qinghui, XIE Liujie, XU Chenyang, et al. Material Removal Modeling and Trochoidal Toolpath Control for Surface Polishing［J］. Journal of South China University of Technology(Natural Science Edition), 2018, 46(3):8-15.
［17］吴昌林, 丁和艳, 陈义. 铝合金车轮CNC机械抛光材料去除深度建模方法研究［J］. 中国机械工程, 2009, 20(21):2558-2562.
WU Changlin, DING Heyan, CHEN Yi. Research on Modeling Method of Material Removal Depth in CNC Mechanical Polishing for Aluminum Alloy Wheel［J］. China Mechanical Engineering, 2009, 20(21):2558-2562.
［18］樊文刚, 刘月明, 王文玺, 等. 基于弹性赫兹接触的钢轨砂带打磨材料去除建模研究［J］. 机械工程学报, 2018, 54(15):191-198.
FAN Wengang, LIU Yueming, WANG Wenxi, et al. Research on Modeling Method of Material Removal for Rail Grinding by Abrasive Belt Based on Elastic Hertzian Contact, 2018, 54(15):191-198.
［19］孙兴伟, 赵正庆, 王可, 等. 螺旋曲面成型抛光用千叶轮的廓型设计及修整方法［J］. 沈阳工业大学学报, 2014, 36(2):176-181.
SUN Xingwei, ZHAO Zhengqing, WANG Ke, et al. Profile Designing and Finishing Method for Flap Wheel Applied in Shaping and Polishing of Spiral Curved Surface［J］. Journal of Shenyang University of Technology, 2014, 36(2):176-181.
［20］PRESTON F W. The Theory and Design of Plate Glass Polishing Machines［J］. Journal of the Society of Glass Technology, 1927, 11:214-256.
［21］计时鸣, 李琛, 谭大鹏, 等. 基于Preston方程的软性磨粒流加工特性［J］. 机械工程学报, 2011, 47(17):156-163.
JI Shiming, LI Chen, TAN Dapeng, et al. Study on Machinability of Softness Abrasive Flow Based on Preston Equation［J］. Journal of Mechanical Engineering, 2011, 47(17):156-163.
［22］JOHNSON K L. Contcact Mechanics［M］. New York:Cambridge University Press, 1985:129-134.

[1]	吴昌林, 丁和艳, 陈义. 材料去除深度与磨粒的关系建模方法研究 [J]. 中国机械工程, 2011, 22(3): 300-304.
[2]	吴昌林;丁和艳;陈义;. 铝合金车轮CNC机械抛光材料去除深度建模方法研究[J]. J4, 2009, 20(21): 0-2531.
[3]	张宪;何洋;计时鸣;王扬渝;赵章风;. 磁控散体抛光装置柔度调节机理研究 [J]. J4, 2008, 19(9): 0-1133.

基于修正Preston方程的百页轮抛光材料去除深度建模

Modeling of Material Removal Depth in ABFW Polishing Based on Modified Preston Equation

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics