Dynamic Fit of Injection Mechanisms for Squeeze Casting Machines Based on Friction Model#br#

doi:10.3969/j.issn.1004-132X.2021.12.003

Abstract

Abstract: Fit clearance was a key factor affecting service and process control of injection mechanisms, in order to study the fit clearance of injection mechanisms, a friction model of the injection mechanisms was proposed. Friction model and numerical simulation were integrated based on secondary development of MSC.MARC software. The results of numerical simulation integrated with friction were compared with those of ordinary numerical simulation without considering friction and the injection experiments to verify effectiveness and accuracy of numerical simulation integrated with friction. Multi-cycle injection processes for the injection mechanisms of 2500 kN squeezing casting machine were simulated, and the changing rules of the fit clearance were studied. In stages of injection and punch return, changes of the fit clearance are severe. In solidification stage, changes of the fit clearance are gentle. Main reason for drastic changes of the fit clearance is the uneven axial temperature distribution in shot-sleeve.

Key words: injection mechanism, friction model, squeezing casting, fitting clearance, numerical simulation

摘要： 配合间隙是影响压射机构服役和工艺控制的核心要素，为研究压射机构配合间隙，提出一种压射机构的摩擦模型，并基于MSC.MARC软件二次开发将摩擦模型与数值模拟整合，整合摩擦的数值模拟结果与不考虑摩擦的普通数值模拟结果和压射实验结果的对比验证了整合摩擦模型数值模拟的有效性和准确性。对2500 kN压铸机压射机构进行多循环压射工艺模拟，研究了工作中配合间隙的变化规律，压射、冲头回程阶段的配合间隙变化剧烈，凝固成形阶段的配合间隙变化平缓，变化剧烈的主要原因是压室的轴向温度分布不均匀。

关键词: 压射机构, 摩擦模型, 挤压铸造, 配合间隙, 数值模拟

CLC Number:

TG233

ZHU Qian, YOU Dongdong, ZHU Quanli, . Dynamic Fit of Injection Mechanisms for Squeeze Casting Machines Based on Friction Model#br#[J]. China Mechanical Engineering, 2021, 32(12): 1405-1413.

朱谦, 游东东, 朱权利, . 基于摩擦模型的挤压铸造机压射机构动态配合[J]. 中国机械工程, 2021, 32(12): 1405-1413.

References

［1］ABID D, KTARI A, MELLOULI D, et al. Failure Analysis of Shot-sleeves Used in Brass High Pressure Die-casting Process［J］. Engineering Failure Analysis, 2019，104:177-188.
［2］宋雷，邵明，游东东. 挤压铸造压射机构的卡擦可靠性分析［J］. 华南理工大学学报(自然科学版)，2013，41(7)：32-37.
SONG Lei，SHAO Ming，YOU Dongdong. Scrapping Reliability Analysis of Injection Device of Squeeze Casting Machine［J］. Journal of South China University of Technology(Natural Science Edition)，2013，41(7)：32-37.
［3］宋雷，邵明，游东东. 利用有限元的挤压铸造压室热力耦合分析［J］. 现代制造工程，2012(11)：19-22.
SONG Lei，SHAO Ming，You Dongdong. The Thermo-mechanical Coupled Analysis of Shot Sleeve in Squeeze Casting Equipment Based on FEM［J］. Modern Manufacturing Engineering，2012(11)：19-22.
［4］白尚平，游东东，李元元. 挤压铸造机压射系统的动态配合数值模拟［J］. 特种铸造及有色合金，2012，32(8)：740-743.
BAI Shangping，YOU Dongdong，LI Yuanyuan. Numerical Simulation of the Dynamic Match for the Injection System of the Squeeze Casting Machine［J］. Special Casting & Nonferrous Alloys，2012，32(8)：740-743.
［5］YU Wenbo，CAO Yongyou，GUO Zhipeng，et al. Development and Application of Inverse Heat Transfer Model between Liquid Metal and Shot Sleeve in High Pressure Die Casting Process under Non-shooting Condition［J］. China Foundry，2016，13(4)：269-275.
［6］YOU Dongdong，WANG Xiang，CHENG Xueyu，et al. Friction Modeling and Analysis of Injection Process in Squeeze Casting［J］. Journal of Materials Processing Technology，2017，239：42-51.
［7］王时龙，冯治恒，雷松，等. 时变摩擦因数对弧齿锥齿轮动力学特性的影响［J］. 中国机械工程，2011，22(2)：148-152.
WANG Shilong，FENG Zhiheng，LEI Song，et al. Effect of Time-varying Friction Coefficient on Dynamics of Spiral Bevel Gears［J］. China Mechanical Engineering， 2011，22(2)：148-152.
［8］刘鹏，陈奇，樊浩，等. 考虑摩擦的球面切向接触刚度分形模型研究［J］. 中国机械工程，2016，27(20)：2773-2778.
LIU Peng，CHEN Qi，FAN Hao，et al. Research on Fractal Model of TCS between Spherical Surfaces Considering Friction Factors［J］. China Mechanical Engineering，2016，27(20)：2773-2778.
［9］刘恩，郭纯. 摩擦磨损试验机研究综述［J］. 现代制造技术与装备，2020，56(12)：35-36.
LIU En，GUO Chun. Review of Friction and Wear Testing Machine［J］. Modern Manufacturing Technology and Equipment，2020，56(12)：35-36.
［10］王会刚，刘晓雯，张忠纯. 压铸机送料冲头磨损机理的有限元分析及实验研究［J］. 铸造技术，2012，33(12)：1410-1411.
WANG Huigang，LIU Xiaowen，ZHANG Zhongchun. Finite Element Analysis and Wear Mechanism Research on Feed Punch of Die-casting Machine［J］. Foundry Technology，2012，33(12)：1410-1411.
［11］赵佳欢，游东东，王翔. 压射机构中压室与冲头间的摩擦性能试验研究［J］. 特种铸造及有色合金，2015，35(4)：390-392.
ZHANG Jiahuan，YOU Dongdong，WANG Xiang. Experiment of the Friction Characteristics between the Punch and Chamber of the Injection Mechanism［J］. Special Casting & Nonferrous Alloys，2015，35(4)：390-392.
［12］VACHHANI H，RATHOD M，SHAH R，et al. Dissolution and Erosion Behavior of AISI H13 Shot Sleeve in High Pressure Die Casting Process［J］. Engineering Failure Analysis，2019，101：206-214.
［13］施炜. 计及润滑条件和空穴效应的活塞环—缸套摩擦副润滑性能研究［D］. 合肥：合肥工业大学，2014.
SHI Wei. Study on the Lubrication Performance of Piston Ring-cylinder Liner Friction Pair Considering Lubrication and Cavation［D］. Hefei:Hefei University of Technology，2014.
［14］HAMID Y，USMAN A，AFAQ S K，et al. Numeric Based Low Viscosity Adiabatic Thermo-tribological Performance Analysis of Piston-skirt Liner System Lubrication at High Engine Speed［J］. Tribology International，2018，126：166-176.
［15］黄平. 润滑数值计算方法［M］. 北京：高等教育出版社，2012.
HUANG Ping. Lubrication Numerical Calculation Methods［M］. Beijing:Higher Education Press，2012.
［16］DAS P，BHUNIYA B，SAMANTA S K，et al. Studies on Die Filling of A356 Al Alloy and Development of a Steering Knuckle Component Using Rheo Pressure Die Casting System［J］. Journal of Materials Processing Technology，2019，271：293-311.

[1]	TUN Fu-Chao, TUN Bai-Hu, ZHANG Xiu-Hua. Numerical Simulation of Heat Transfer Performance of Paraffin Thermal-Sensitive Valve  [J]. J4, 201016, 21(16): 1921-1926.
[2]	FU Boyu, XU Zehua, LI Kangshuai, WANG Haoyu, HE Jiaqi, HE Qiang. Numerical Simulation and Experimental Analysis of Propeller Flow Fields and Motor Temperature Fields in High-altitude Environments for UAVs [J]. China Mechanical Engineering, 2025, 36(12): 2894-2902.
[3]	ZHANG Peng1, 3, 4, 5, ZHU Xuewei2, 3, 4, YU Baoyang1, 3, 4, WU Tianfeng1, 3, 4, ZHU Jinzhou1, 3, 4. Flow Behavior and Microstructure of 304 Stainless Steel Ultra-thin Strips in Microchannel Gas Forming [J]. China Mechanical Engineering, 2025, 36(07): 1416-1422.
[4]	FAN Zhisong, LI Ning, XU Likai, DENG Jianghua. Research on Magnetic Pulse Expansion Joining of 6063 Aluminum/Steel 20 Tubes [J]. China Mechanical Engineering, 2024, 35(12): 2185-2192.
[5]	LI Yanle, PAN Zhongtao, QI Xiaoxia, CUI Weiqiang, CHEN Jian, LI Fangyi. Effect of Heat Treatment on Temperature and Stress Distribution during Laser Cladding of 316L Steels [J]. China Mechanical Engineering, 2024, 35(04): 666-677.
[6]	PENG Wenfei, ZHANG Cheng, LIN Longfei, HUANG Minghui, YU Feng. Modeling and Prediction of Central Damages in Cross Wedge Rolling Based on Continuous Damage Mechanics [J]. China Mechanical Engineering, 2024, 35(04): 711-720,751.
[7]	LI Kunhang, ZHANG Siqi, WU Wei, HU Mingzhuo, SUN Yaling, XIONG Xin, HUANG Hong. Multi-field Coupling Simulation and Analysis for Resistance Spot Welding of Three-layer Dissimilar Unequal-thickness Steels [J]. China Mechanical Engineering, 2023, 34(24): 2996-3003.
[8]	LUO Wenze, CHENG Huimei, LIU Hongyan, WANG Yifeng, YE Yanhong, DENG Dean. Numerical Simulation of Residual Stress and Welding Deformation for High Strength Steel Q960E Butt-welded Joints [J]. China Mechanical Engineering, 2023, 34(17): 2095-2105,2141.
[9]	XU Xiang, ZHANG Yilun, MEI Zheng, LI Jian, WANG Dan, MU Liansong. Numerical Simulation and Experimental Investigation of Flow Fields in Vehicle Climatic Chambers [J]. China Mechanical Engineering, 2023, 34(17): 2115-2123.
[10]	ZHU Yulong, ZHAO Yingsong, FANG Yang, CHEN Hongen, CHEN Zhenmao, . Rotating Eddy Current Testing for Inspection of Cracks at Hole Edge [J]. China Mechanical Engineering, 2023, 34(08): 883-891.
[11]	ZHANG Yinan, DING Jianwan. Friction Model of Robot Joints Considering Influences of Temperature [J]. China Mechanical Engineering, 2023, 34(02): 127-134.
[12]	QIN Deng, DAI Zhiyuan, ZHOU Ning, LI Tian. Effects of Pantograph Subsidence on Its Aerodynamic and Acoustic Behaviors [J]. China Mechanical Engineering, 2022, 33(20): 2509-2519.
[13]	LI Wei, ZHENG Hao, LIU Yanmei, FAN Song. Numerical Simulation on Mounted Bolt Failures in Vehicle Subframe [J]. China Mechanical Engineering, 2022, 33(19): 2388-2393.
[14]	HU Futai, . Cracking Suppression and Lateral Bending Broadening Strategy of Fan-shaped Thin-wall Ribs during Extrusion [J]. China Mechanical Engineering, 2022, 33(14): 1734-1740.
[15]	MA Yi, CHEN Yutao, MENG Xiangkai, ZHAO Wenjing, PENG Xudong, . Transient Start-up Dynamics Model and Sealing Performance of Single Metal Seals in Cone Bits [J]. China Mechanical Engineering, 2022, 33(07): 777-785.