Study on Effects of Tooth Root Transition Arc on Grinding Temperature and Residual Stress during Full Tooth Groove Profile Grinding

doi:10.3969/j.issn.1004-132X.2022.11.0003

Abstract

Abstract: A three-dimensional FE (finite element) simulation model of the grinding temperature field was proposed by considering the coupling effects of three adjacent heat sources（tooth bottom heat source， transition arc heat source and tooth profile heat source）to calculate the grinding temperature in profile grinding of full tooth grooves. Then， the residual stresses caused by grinding were calculated by the FE method based on thermal structure coupling. The characteristics of the grinding temperature and residual stress fields were analyzed， as well as the influences of the size of the tooth root transition arcs on the grinding temperature and the residual stress distribution at the tooth root after grinding. The results show that the effects of the transition arc radius on the grinding temperature are relatively small， but the effects on the residual stress are relatively large. Compared with a tooth groove without transition arcs， the maximum residual stress after grinding is reduced by more than 20% when the radius of the transition arcs exceeds 2 mm. The measurement results are consistent with the FE simulation ones， which proves the correctness of the simulation results.

Key words: profile grinding, gear, tooth root transition arc, grinding temperature, residual stress

摘要： 在齿轮全齿槽成形磨削过程中，考虑相邻三个热源（齿底热源、过渡圆弧热源、齿廓热源）的耦合效应，建立了磨削温度场的三维有限元仿真模型，计算了全齿槽成形磨削温度，并在此基础上，采用基于热-结构耦合的有限元方法计算了磨削引起的残余应力，分析了磨削温度场和残余应力场的分布特征，以及齿根过渡圆弧的大小对磨削温度和磨削后齿根处残余应力分布的影响。结果表明，过渡圆弧半径对磨削温度的影响相对较小，但对齿根处残余应力的影响较大；与没有过渡圆弧的齿槽相比，当过渡圆弧半径超过2 mm时，磨削后齿根最大残余应力降低20%以上。实验测量结果与有限元仿真结果一致，证明了模拟结果的正确性。

关键词: 成形磨削, 齿轮, 齿根过渡圆弧, 磨削温度, 残余应力

CLC Number:

TG580

YI Jun , GONG Zhifeng, YI Tao, ZHOU Wei, . Study on Effects of Tooth Root Transition Arc on Grinding Temperature and Residual Stress during Full Tooth Groove Profile Grinding[J]. China Mechanical Engineering, 2022, 33(11): 1278-1286.

易军, 龚志锋, 易涛, 周炜, . 齿根过渡圆弧对全齿槽成形磨削温度和残余应力影响的研究[J]. 中国机械工程, 2022, 33(11): 1278-1286.

References

［1］DENKENA B， KHLER J， SCHINDLER A， et al. Continuous Generating Grinding：Material Engagement in Gear Tooth Root Machining［J］. Mechanism & Machine Theory， 2014， 81：11-20.
［2］刘谦，杨理钧，田欣利，等. 基于微晶刚玉砂轮的20CrMnTi齿轮成型磨削表面完整性［J］. 工程科学学报， 2018， 40（3）：357-365.
LIU Qian， YANG Lijun， TIAN Xinli， et al. Surface Integrity of Form Grinding 20CrMnTi Gear Based on a New Microcrystalline Corundum Wheel［J］. Chinese Journal of Engineering， 2018， 40（3）：357-365.
［3］JERMOLAJEV S， BRINKSMEIER E， HEINZEL C. Surface Layer Modification Charts for Gear Grinding［J］. CIRP Annals， 2018， 67（1）：333-336.
［4］REGO R， LPENHAUS C， GOMES J， et al. Residual Stress Interaction on Gear Manufacturing［J］. Journal of Materials Processing Technology， 2018， 252：249-258.
［5］张魁榜，韩江，夏链，等. 齿轮成形磨削加工热力耦合数值仿真研究［J］. 合肥工业大学学报（自然科学版）， 2015， 38（10）：1297-1302.
ZHANG Kuibang， HAN Jiang， XIA Lian， et al. Numerical Simulation of Thermo-mechanical Coupling of Gear Form Grinding Process［J］. Journal of Hefei University of Technology（Natural Science）， 2015， 38（10）：1297-1302.
［6］WANG Y Z， CHU X M， HUANG Y Z， et al. Surface Residual Stress Distribution for Face Gear under Grinding with a Long-radius Disk Wheel［J］. International Journal of Mechanical Sciences， 2019， 159：260-266.
［7］WANG Z， CHEN L， LIU Z M， et al. Accurate Control of Residual Stress Distribution along the Complex Surface Depth at the Root of Gears［J］. Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science， 2020， 234（21）：4321-4330.
［8］万国新，唐进元，李国文，等. 齿根过渡圆角半径对齿根裂纹扩展的影响规律研究［J］. 机械传动， 2017， 41（4）：101-105.
WAN Guoxin， TANG Jinyuan， LI Guowen， et al. An Investigation of Influence of Transition Arc Radius on the Tooth Root Crack Propagation［J］. Journal of Mechanical Transmission， 2017， 41（4）：101-105.
［9］DONG P， ZUO S M， DU S F， et al. Optimum Design of the Tooth Root Profile for Improving Bending Capacity［J］. Mechanism and Machine Theory， 2020， 151：103910.
［10］YI J， JIN T， ZHOU W， et al. Theoretical and Experimental Analysis of Temperature Distribution during Full Tooth Groove Form Grinding［J］. Journal of Manufacturing Processes， 2020， 58：101-115.
［11］DING W， ZHANG L， LI Z， et al. Review on Grinding-induced Residual Stresses in Metallic Materials［J］. International Journal of Advanced Manufacturing Technology， 2017， 88（9/12）：2939-2968.
［12］王利增. 工艺参数对20CrMnTi渗碳钢的组织性能和表面残余应力的影响［D］. 大连：大连交通大学， 2011.
WANG Lizeng. The Effect of Technics Parameter on the Microstructure Property and Residual Stress of 20CrMnTi Carburization Steel［D］. Dalian：Dalian University of Technology， 2011.
［13］JIN T， STEPHENSON D J. Heat Flux Distributions and Convective Heat Transfer in Deep Grinding［J］. International Journal of Machine Tools & Manufacture， 2005， 46（14）：1862-1868.
［14］任敬心，华定安. 磨削原理［M］. 北京：电子工业出版社， 2011.
REN Jingxin， HUA Dingan. Princple of Grinding［M］. Beijing：Publishing House of Electronics Industry， 2011.
［15］TANG J Y， DU J， CHEN Y P. Modeling and Experimental Study of Grinding Forces in Surface Grinding［J］. Journal of Materials Processing Technology， 2008， 209（6）：2847-2854.
［16］YI J， JIN T， DENG Z H. The Temperature Field Study on the Three-dimensional Surface Moving Heat Source Model in Involute Gear Form Grinding［J］. The International Journal of Advanced Manufacturing Technology， 2019， 103（5/8）：3097-3108.
［17］ROWE W B. Thermal Analysis of High Efficiency Deep Grinding［J］. International Journal of Machine Tools & Manufacture， 2001， 41（1）：1-19.
［18］李征，丁文锋，周欢，等. 基于混合材料模型的颗粒增强钛基复材高速磨削温度研究［J］. 机械工程学报， 2019， 55（21）：186-198.
LI Zheng， DING Wenfeng， ZHOU Huan， et al. Grinding Temperature of Particulate Reinforced Titanium Matrix Composites in High-speed Grinding Based on Multi-material Model［J］. Journal of Mechanical Engineering， 2019， 55（21）：186-198.

[1]	CHEN Li-Feng, TUN Xiao-Ling, QIN Da-Tong, XIAO Zheng-Meng. Study on Frictional Power Losses of Spur Gear [J]. J4, 201016, 21(16): 1911-1915.
[2]	WANG Rong, LI Junjie, ZHENG Wenge, WANG Jia, HE Mingrong. Gear Fatigue Damage Prediction with Coupling Effect of Environmental Randomness and Load Sequence [J]. China Mechanical Engineering, 2026, 37(1): 105-113.
[3]	ZHANG Xu, LI Congbo, ZHANG You, ZHANG Chenghui, ZHOU Feng. Geometric Parameter Optimization Method of Honing Wheels for Lower-noise Texture [J]. China Mechanical Engineering, 2025, 36(12): 2875-2884.
[4]	Shuai MO, Xuan HUANG, Wenbin LIU, Wei ZHANG. Nonlinear Dynamics of Continuously Tunable Planetary Gear Metamaterial [J]. China Mechanical Engineering, 2025, 36(11): 2509-2516.
[5]	Chenfan JIA, Huaiju LIU, Caichao ZHU, Taimin CHEN, Jinxiao CHEN. An Aviation Gear Bulk Temperature Prediction Method and Verification Research Based on CatBoost [J]. China Mechanical Engineering, 2025, 36(08): 1658-1667.
[6]	Jinzhan SU, Yaoke FENG, Bin LIU, Xinlong CAO, Linlin SUN. Analysis and Optimization of Meshing Performance of Straight Bevel Gears Machined by Dual Interlocking Circular Cutters [J]. China Mechanical Engineering, 2025, 36(08): 1683-1690.
[7]	Jiyuan HAN, Jiahao ZHANG, Yong ZHAN, Hongyi ZHANG, Dongyue QU. Prediction of Residual Stress in Boring Main Bearing Holes of Marine Diesel Engine Bodies [J]. China Mechanical Engineering, 2025, 36(08): 1883-1892.
[8]	HUANG Hao1, WANG Zeng2, LI Bo2, LU Zehua1, LIU Huaiju1. Structure-thermal Compliance Collaborative Topology Optimization of Aero-engine Gears Transmission Case Based on Compromise Programming Method [J]. China Mechanical Engineering, 2025, 36(07): 1471-1478.
[9]	NIU Yanzhao1, LIU Hongwei1, SONG Yali2, ZHU Xianglong1, HUANG Jiamei2, KANG Renke1. Optimization and Experimental Study of Bolt Retreat Groove Rolling Wheels Based on Finite Element Simulation [J]. China Mechanical Engineering, 2025, 36(06): 1214-1221.
[10]	LI Guangjun1, 2, MA Jing1, 2, DUAN Hong1, 2, HU Xiwen1, 2, XU Lei1, 2, MAO Shimin3, PENG Xianlong4. Numerical Rolling Tests of Actual Measured Tooth Surfaces for Oversized Face Gears [J]. China Mechanical Engineering, 2025, 36(05): 1008-1017.
[11]	SUN Hao1, LAN Qixin2, YAO Bin2, LU Jingjing1, ZHANG Jinhui2, PAN Zhirong2, ZHAO Kexin2. Study on Lubricating Performances and Mechanism of Nano-carbon Balls Cutting Fluids [J]. China Mechanical Engineering, 2025, 36(04): 715-723.
[12]	ZHOU Jinhua1, 2, QI Qi1, 2, REN Junxue1, 2, ZHAN Mei1, 2. Inverse Solution for TC4 Residual Stress Gradient Distribution in Four-axis Milling with Tapered Ball-end Cutters [J]. China Mechanical Engineering, 2025, 36(04): 770-779.
[13]	MO Shuai1, 2, 3, HUANG Xuan1, 2, HUANG Zurui1, 2, ZHANG Wei1. Continuous Multi-stable Gear Cell Mechanical Metastructures and Mechanics Properties [J]. China Mechanical Engineering, 2025, 36(04): 857-863，887.
[14]	TAO Dehua1, WANG Ying2, CAO Zhenxin1, LI Ning1, HU Liguang1, XUAN Zhongyi1, JIANG Hongkui1. Analysis of Transmission Characteristics of Multi-stage Denatured Pascal Worm Gears [J]. China Mechanical Engineering, 2025, 36(03): 475-482.
[15]	LIU Huaiju, LU Zehua, ZHU Caichao. State-of-the-art and Trend of High Loading Capacity Plastic Gear Drives [J]. China Mechanical Engineering, 2025, 36(01): 2-17.