基于蠕滑理论的精密滚珠丝杠副摩擦力研究

中国机械工程 ›› 2016, Vol. 27 ›› Issue (02): 178-186.

基于蠕滑理论的精密滚珠丝杠副摩擦力研究

陈勇将1;汤文成2;干为民1;孟浩东1

1.常州工学院,常州,213002
2.东南大学,南京,211189

出版日期:2016-01-25 发布日期:2016-12-15
基金资助:
国家科技重大专项(2013ZX04008-011）；江苏省高校自然科学研究面上项目（15KJB460001）

Study on Friction of Precision Ball Screws Based on Creep Force Models

Chen Yongjiang1;Tang Wencheng2;Gan Weimin1;Meng Haodong1

1.Changzhou Institute of Technology,Changzhou,Jiangsu,213002
2.Southeast University,Nanjing,211189

Online:2016-01-25 Published:2016-12-15
Supported by:

摘要/Abstract

摘要：

考虑不同相位角处滚珠所受离心力及摩擦力的影响，建立了双螺母预紧式滚珠丝杠副多自由度动力学模型，该模型不再基于所有滚珠受力相等和运动相同的假设，使用蠕滑力模型来表征滚珠与滚道接触界面间的摩擦力；利用经验模态分解（EMD）包络分析方法进行了滚珠丝杠副振动信号撞击频率的提取，与理论计算结果进行对比，对动力学模型进行了验证；分析了丝杠转速、轴向载荷、滚道曲率比和导程对滚珠丝杠副摩擦力的影响规律。

关键词: 滚珠丝杠副, 动态特性, 摩擦力, 经验模态分解

Abstract:

After establishing a proper friction force model to define the slip component between the ball and raceways,instead of assuming that all balls in the ball screw were equally loaded and run at the same speed,a multi degree of freedom dynamic model of the double nut preload ball screw was developed.The impact frequency of balls on the cover of the returning tube was obtained by using with the EMD and envelope method.Through theoretically calculated values with the experimental measured values of ball impact frequency the correctness of the established dynamics model was verified.The effects of screw rotational speeds,axial loads,pitch and curvature ratio on the friction of ball screws were investigated.

Key words: ball screw, dynamic characteristics；friction force；empirical mode decomposition(EMD)

中图分类号:

TH132.1

陈勇将, 汤文成, 干为民, 孟浩东. 基于蠕滑理论的精密滚珠丝杠副摩擦力研究[J]. 中国机械工程, 2016, 27(02): 178-186.

Chen Yongjiang, Tang Wencheng, Gan Weimin, Meng Haodong. Study on Friction of Precision Ball Screws Based on Creep Force Models[J]. China Mechanical Engineering, 2016, 27(02): 178-186.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.cmemo.org.cn/CN/

https://www.cmemo.org.cn/CN/Y2016/V27/I02/178

参考文献

[1]周勇,王国贤,曹小华.一种滚珠丝杠扭转振动模态的测量与分析方法[J].中国机械工程,2013,24(23):3240-3243.
Zhou Yong,Wang Guoxian,Cao Xiaohua.A Measuring and Analysis Method to Identify Torsional Vibration Modes of Ball Screw Feed Drives[J].China Mechanical Engineering,2013,24(23):3240-3243.
[2]王福吉，阳江源，贾振元，等. 滚珠丝杠副非协调性接触特性研究[J]. 中国机械工程,2011,22(19):2293-2297.
Wang Fuji，Yang Jiangyuan，Jia Zhenyuan, et al.Study on Non-conformal Contact Characteristics of Ball Screw [J]. China Mechanical Engineering,2011,22(19):2293-2297.
[3]Wei C C,Lai R S.Kinematical Analyses and Transmission Efficiency of a Preloaded Ball Screw Operating at High Rotational Speeds[J].Mechanism and Machine Theory,2011,46(7):880-898.
[4]Wei C C,Liou W L,Lai R S.Wear Analysis of the Offset Type Preloaded Ball-screw Operating at High Speed[J]. Wear, 2012, 292: 111-123.
[5]Olaru D,Puiu G C,Balan L C,et al.A New Model to Estimate Friction Torque in a Ball Screw System[M].Product Engineering. Berlin: Springer, 2004.
[6]陈勇将，汤文成. 微型滚珠丝杠副摩擦力矩模型的建立与实验验证[J]. 东南大学学报,2011,41(5):983-986.
Chen Yongjiang,Tang Wencheng.Theoretical and Experimental Research on Friction Torque Model of Micro-type Ball Screw[J]. Journal of Southeast University,2011,41(5):983-986.
[7]Kalker J J. A Fast Algorithm for the Simplified Theory of Rolling Contact [J]. Vehicle System Dynamics,1982, 11(1):1-13.
[8]Kalker J J.Three-dimensional Elastic Bodies in Rolling Contact[M].Dordrecht:Kluwer Academic Publishers,1990.
[9]Chen Y J,Tang W C.Dynamic Contact Stiffness Analysis of a Double-nut Ball Screw Based on Quasi-static Method[J].Mechanism and Machine Theory Journal,2014,73(3):76-90.
[10]Harris T A.Rolling Bearing Analysis[M].New York:John Wiley & Sons,2007.
[11]Feng G H,Pan Y L.Investigation of Ball Screw Preload Variation Based on Dynamic Modeling of a Preload Adjustable Feed-drive System and Spectrum Analysis of Ball-nuts Sensed Vibration Signals[J].International Journal of Machine Tools and Manufacture, 2012, 52(1):85-96.

[1]	李国龙, 赵晓亮, 王玉, 陶一杰. 复杂工况下磨齿机主轴运行模态的分析方法[J]. 中国机械工程, 2026, 37(1): 51-59.
[2]	徐洋, 祖莉, 李伟龙, 刘晓玲, 何建樑, 刘俊. 基于随机森林算法的行星滚柱丝杠副摩擦力矩预测[J]. 中国机械工程, 2025, 36(07): 1505-1511.
[3]	樊玉杰, 陈俣哲, 郝梦杰, 王苏扬, 杜宇辰, 夏晶, 管小燕. 复合润滑结构改善滑动导轨表面爬行现象研究[J]. 中国机械工程, 2024, 35(10): 1740-1746,1761.
[4]	李大柱, 牛江, 梁树林, 池茂儒. 时频能量谱与 VGG16结合的车轮扁疤损伤程度估计方法[J]. 中国机械工程, 2023, 34(16): 1907-1914.
[5]	钱门贵, 陈涛, 于耀翔, 郭亮, 高宏力, 李威霖, . 一种改进基尼指数加权的轴承健康指标构建方法[J]. 中国机械工程, 2023, 34(15): 1813-1819，1855.
[6]	李朕均, 赵春雨. 进给系统角接触球轴承的热力耦合分析[J]. 中国机械工程, 2023, 34(07): 821-829.
[7]	周鑫, 李阁强, 雷贤卿, 许增健. 集成能量再生模块的全液压转向系统分析[J]. 中国机械工程, 2022, 33(18): 2227-2233.
[8]	王庆港, 陈源, 彭旭东, 李运堂, 李孝禄, 王冰清, 金杰. 三自由度微扰下箔片端面气膜密封动态特性分析[J]. 中国机械工程, 2022, 33(15): 1828-1840.
[9]	李瑞, 孟祥慧, 谢友柏. 船用低速机关键摩擦副建模分析与摩擦力无线测量验证[J]. 中国机械工程, 2022, 33(04): 380-387，396.
[10]	秦大同, 吕雪慧, 陈锐博, 杨战斌. 运行工况下风电传动系统机电耦合建模及其动态特性分析[J]. 中国机械工程, 2022, 33(03): 253-260.
[11]	梁医, 王旭东, 王晓艺, 冯健文, 冯本哲, 欧屹, 冯虎田. 滚动直线导轨副的滚道中心距误差与承载性能的关系[J]. 中国机械工程, 2021, 32(18): 2254-2261,2267.
[12]	郭俊超, 甄冬, 孟召宗, 师占群, 谷丰收. 基于WAEEMD和MSB的滚动轴承故障特征提取[J]. 中国机械工程, 2021, 32(15): 1793-1800.
[13]	席静谣, 周长光, 冯虎田, 张鲁超. 几何误差和倾覆力矩对双螺母滚珠丝杠副载荷分布的影响#br#[J]. 中国机械工程, 2021, 32(10): 1181-1190.
[14]	刘涛1,2;韩炎1,2;孙仁福1,2;赵丁选1,2. 数字型液压变压器动态特性研究[J]. 中国机械工程, 2021, 32(03): 284-289.
[15]	张耀满;暴凤旭;齐培宁. 滚珠丝杠螺母副热态特性建模方法[J]. 中国机械工程, 2020, 31(20): 2486-2490,2496.