#br#
Effects of Dimensional Errors on Friction Power of a Rotor System

China Mechanical Engineering ›› 2012, Vol. 23 ›› Issue (11): 1345-1349.

Previous Articles Next Articles

#br# Effects of Dimensional Errors on Friction Power of a Rotor System

Wei Yuan;Xu Wubin;Zeng Haijing;Zhang Zhouqiang

Guangxi University of Technology, Liuzhou, Guangxi, 545006

Online:2012-06-10 Published:2012-06-14
Supported by:

National Natural Science Foundation of China（No. 50865001）;
Guangxi Provincial Natural Science Foundation of China（No. 2011GXNSFF018004）

尺寸误差对转子系统摩擦功率的影响

魏塬;徐武彬;曾海景;张周强

广西工学院,柳州,545006

基金资助:
国家自然科学基金资助项目（50865001）；广西自然科学基金资助项目（2011GXNSFF018004）；广西研究生教育创新计划资助项目（2011105940802M02）
National Natural Science Foundation of China（No. 50865001）;
Guangxi Provincial Natural Science Foundation of China（No. 2011GXNSFF018004）

Abstract

Abstract:

According to the existences of dimensional errors on hydrodynamic journal bearing system, a nonlinear oil film force model was established.It emphasised on analyzing the errors of bearing diameter and journal diameter along with its interaction effects on the dynamics, carrying capacity, stability of the hydrodynamic journal bearing system. The effects on friction power loss of the hydrodynamic journal bearing system were analyzed quantitatively based on the eccentricity corresponding to the critical speed of the stability. From the diagram, it is easy to know that the dimensional errors will have different degrees of impact on the journal bearing system, the friction power decreases as the eccentricity increases, and when the eccentricity at nearly 0.6948 the friction power reaches to a minimum. The results provide a reliable theory for reducing the friction power loss, and the parameter design of journal bearing system rationally. 

Key words: hydrodynamic journal bearing, dimensional error, critical speed, friction power

摘要：

针对滑动轴承转子系统存在的尺寸误差,建立了非线性油膜力模型,着重研究了滑动轴承与轴颈直径误差及其交互作用对系统动力学特性、承载能力和稳定性的影响,并利用稳定性临界转速对应的偏心率,定量分析了偏心率对滑动轴承转子系统摩擦功率损失的影响。图形曲线分析表明,各种尺寸变化对系统会产生不同程度的影响,摩擦功率随着偏心率的增大而减小,当偏心率在0.6948附近时摩擦功率达到最小。研究结果为减小系统功耗、合理设计系统参数提供了可靠的依据。


关键词: 滑动轴承, 尺寸误差, 临界转速, 摩擦功率

CLC Number:

TH113

WEI Yuan, XU Wu-Ban, CENG Hai-Jing, ZHANG Zhou-Jiang. #br# Effects of Dimensional Errors on Friction Power of a Rotor System[J]. China Mechanical Engineering, 2012, 23(11): 1345-1349.

魏塬, 徐武彬, 曾海景, 张周强. 尺寸误差对转子系统摩擦功率的影响[J]. 中国机械工程, 2012, 23(11): 1345-1349.

References

[1]闻邦椿等著.故障旋转机械非线性动力学的理论与试验[M],2004:329.
[2]Hargreaves D J, Fillon M. Analysis of a Tilting Pad Journal Bearing to Avoid Pad Fluttering[J]. Tribology International, 2007,40 :607-612.
[3]吴起,池长青.制造误差对气体静压圆柱轴承静态特性的FEM分析[J].航空学报,1997,18(6):703-708.
[4]边新孝[1],李谋渭[1],李威[1].加工误差对气体静压径向轴承的影响[J].北京科技大学学报,2005,27(3):331-333.
[5]Ighil N T, Bounif A, Maspeyrot P. Thermo--hy- drodynamic Study of the Journal Bearing Under Static Load [J]. Mechanical Engineering Science, 2008,222: 1801-1809.
[6]刘大全.考虑温粘热效应的滑动轴承非线性油膜力模型研究及其应用[D].复旦大学,2005:
[7]张伟忠[1],焦映厚[2],陈照波[2].滑动轴承非线性油膜力模型的对比分析[J].汽轮机技术,2011(1):24-26.
[8]徐武彬[1],王镇江[1],陈其兵[1],李冰[1],张宏献[1].基于Sommerfeld数的滑动轴承转子系统稳定性分析[J].中国机械工程,2009(23):2875-2879.
[9]Dong D L. The Effect of Oil Aeration on the Behav- ior of Journal Bearings[D]. Staffordshire, UK: Staffordshire University, 2006.
[10]Ogrodnik P J. Operation of Rotor-bearing Sys- tems Subjected to Dynamic Conical Misalignment [D]. Staffordshire, UK: Staffordshire Universi- ty, 1989.
[11]刘凯[1],牛世勇[1],刘中[2],阮忠唐[1],.滚柱轴承离合器滚动摩擦功耗分析[J].机械科学与技术,1998,17(4):603-604.
[12]崔东辉[1],徐龙祥[1].机械加工误差对主动磁悬浮轴承性能的影响[J].机械工程学报,2009,45(6):24-33.
[13]Nikolakopoulos P G, Papadopoulos C A. A Study of Friction in Worn Misaligned Journal Bearings Under Severe Hydrodynamic Lubrication[J]. Tri- bology International, 2008,41 : 461-472.
[14]陈存祖.关于油浸径向滑动轴承摩擦功率计算问题的探讨.南昌水专学报,1988.

#br# Effects of Dimensional Errors on Friction Power of a Rotor System

尺寸误差对转子系统摩擦功率的影响

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 11

Recommended Articles

Metrics

[1]	GUO Ming, NIE Songlin, JI Hui, YIN Fanglong. Design and Lubrication Characteristics of a New Integrated Slipper/Swashpalte Interface in Seawater Hydraulic Piston Pumps [J]. China Mechanical Engineering, 2022, 33(24): 2942-2952.
[2]	WANG Zhiqiang, , LEI Zhenyu, . Study on Influence Parameters of Rail Corrugation on Tangential Tracks of Metro [J]. China Mechanical Engineering, 2021, 32(04): 420-430.
[3]	Wang Jianghui, Xu Wubin, Li Bing, Li Xiaolei. A New Method for Judging Criticat Speed of Nonlinear Bearing Rotor System [J]. China Mechanical Engineering, 2016, 27(14): 1964-1968.
[4]	Mao Wengui, Han Xu, Liu Guiping. Research on Dynamic Characteristics of Sliding Bearing Nonlinear Oil-film Based on Fluid-structure Interaction [J]. China Mechanical Engineering, 2014, 25(3): 383-387,403.
[5]	Yu Dezhong;Xu Xianghong. Dimensional Error Modeling Analysis and Simulation of Sheet Metal MultiStage Assemblies [J]. China Mechanical Engineering, 2013, 24(17): 2331-2336.
[6]	CENG Hai-Jing, XU Wu-Ban, WEI Yuan, ZHANG Hong-Xian, HU Jun-Jun. Friction Power Loss Analysis of Hydrodynamic Bearing Rotor System Allowing for Roundness Errors [J]. China Mechanical Engineering, 2012, 23(8): 906-909.
[7]	LONG Xiao-Beng, NIU Kun, WEI Sai-Yuan. Research on Hydrodynamic Lubrication Performance of Journal Bearings Based on General Film Thickness Equation Using CFD Software [J]. China Mechanical Engineering, 2012, 23(21): 2521-2524.
[8]	ZHANG Hong-Xian, XU Wu-Ban, WANG Tian-Jiang, CHEN Ji-Bing, LI Bing. Effects of Ovality Errors on Dynamics Stability of Elliptic Hydrodynamic Journal Bearings [J]. China Mechanical Engineering, 2011, 22(20): 2466-2469.
[9]	HU Xu-1, JUE Zong-Chang-1, XU Mo-Na-2, SUN Jin-Ju-1. Geometric Theory for a Translational Rotary Compressor [J]. China Mechanical Engineering, 2011, 22(16): 1896-1900.
[10]	WANG Hong-Chao, GUO Lei-Lei, MO Li, XU Shuo-Yuan. Critical Speed Calculation of Rigid Rotor Supported by AMB [J]. China Mechanical Engineering, 2010, 21(8): 904-907.
[11]	XU Wu-Ban, WANG Tian-Jiang, CHEN Ji-Bing, LI Bing, ZHANG Hong-Xian. Stability Analysis of Hydrodynamic Journal Bearing System Based on Sommerfeld Number [J]. J4, 2009, 20(23): 2875-2879.