基于装配定位优先级的并联结合面误差建模

中国机械工程 ›› 2015, Vol. 26 ›› Issue (24): 3295-3301.

基于装配定位优先级的并联结合面误差建模

吕程;刘子建

湖南大学汽车车身先进设计制造国家重点实验室,长沙,410082

出版日期:2015-12-25 发布日期:2015-12-17
基金资助:
国家自然科学基金资助项目(51175161,51305132)

Parallel Joint Surface Error Modeling Based on Assembly Positioning Priority

Lü Cheng;Liu Zijian

State Key Laboratory of Advanced Design and Manufacture for Vehicle Body,Hunan University,Changsha,410082

Online:2015-12-25 Published:2015-12-17

摘要/Abstract

摘要：

分析了并联结合面在装配定位优先级意义下装配误差的形成机理与计算方法。针对常见的平面结合面与圆柱结合面，分析了误差形成和装配精度失效的原因,采用小位移旋量(SDT)法描述了误差变动。针对并联结合面间位姿变动的相互影响，定义了装配定位优先级的概念，并详细分析了并联结合面装配定位优先级的判定依据。根据装配定位优先级确定了并联的各结合面误差组成及计算方法。列举了常见的并联结合面形式，并以一组常见并联结合面的装配误差分析为例，验证了该方法的可行性，为装配体误差分析、零件精度设计、装配成功率计算等提供了借鉴。

关键词: 并联结合面, 小位移旋量法, 装配定位优先级, 结合面误差建模

Abstract:

The formation mechanism and calculation method of assembly error of parallel joint surface under the effects of assembly positioning priority were analyzed.In view of the common plane joint surface and cylindrical joint surface,the formation of joint surface error and the invalid reason of assembly precision were analyzed,the variations of errors were described by SDT method.In view of the interplay of position change between parallel joint surfaces, the concept of assembly positioning priority was defined,and the judgment criterions of the assembly positioning priority of parallel joint surface were analyzed in details.The specific composition and calculation methods of the errors of all parallel joint surfaces were determined based on the assembly positioning priority.The common forms of parallel joint surface were listed,and one of them was taken as an example for assembly error analysis.As a result, the practicability of this method was verified,and the references of assembly error analyses,part precision design,assembly success rate calculation and so on were provided.

Key words: parallel joint surface；small displacement torsor method, assembly positioning priority, joint surface error modeling

中图分类号:

TH115

吕程, 刘子建. 基于装配定位优先级的并联结合面误差建模[J]. 中国机械工程, 2015, 26(24): 3295-3301.

Lü Cheng, Liu Zijian. Parallel Joint Surface Error Modeling Based on Assembly Positioning Priority[J]. China Mechanical Engineering, 2015, 26(24): 3295-3301.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2015/V26/I24/3295

参考文献

[1]杨将新,徐旭松,曹衍龙,等.基于装配定位约束的功能公差规范设计[J].机械工程学报,2010,46（2）：1-8.
Yang Jiangxin,Xu Xusong,Cao Yanlong,et al.Functional Tolerance Specification Design Based on Assembly Positioning[J].Chinese Journal of Mechanical Engineering,2010,46（2）：1-8.
[2]李春丽.复杂产品的三维功能公差分析方法研究[D].北京:北京工业大学,2013.
[3]Anselmetti B,Mejbri H,Mawussi K.Coupling Experimental Design-digital Simulation of Junctions for the Development of Complex Tolerance Chains[J].Computers in Industry,2003,50（3）:277-292.
[4]Anselmetti B.Generation of Functional Tolerancing Based on Positioning Features[J].Computer-aided Design,2006,38(8):902-919.
[5]蒋科,刘检华,宁汝新,等.定位优先级约束下间隙配合的变动解析与装配成功率计算[J].机械工程学报,2014,50（15）：136-146.
Jiang Ke,Liu Jianhua,Ning Ruxin,et al.Variation　Analysis and Assembly Success Rate Computation for Clearance Fit under Constraint of Location Priority[J].Chinese Journal of Mechanical Engineering,2014,50(15):136-146.
[6]Camelio J,Hu S J,Ceglarek D.Modeling Variation Propagation of Multi-station Assembly Systems with Compliant Parts[J].Journal of Mechanical Design,2003,125(4):673-681.
[7]Bourdet P,Mathieu L,Lartigue C,et al.The Concept of Small Displacement Torsor in Metrology[J].Series on Advances in Mathematics for Applied Sciences,1996,40:110-122.
[8]黄强,李青锋.机床通用误差模型的建立及应用[J].中国机械工程,2013,24(12):1626-1630.
Huang Qiang,Li Qingfeng.Buliding and Application of General Model for Machine Tool Errors[J].China Mechanical Engineering, 2013, 24(12): 1626-1630.
[9]Rocha C R,Tonetto C P,Dias A. A Comparison between the Denavit-hartenberg and the Screw-based Methods Used in Kinematic Modeling of Robot Manipulators[J].Robotics and Computer-integrated Manufacturing,2011,27(4):723-728.
[10]Chiabert P,Orlando M.About a CAT Model Consistent with ISO/TC 213 Last Issues[J].Journal of Materials Processing Technology, 2004, 157/158:61-66.
[11]Mejbri H,Anselmetti B,Mawussi K.Functional Tolerancing of Complex Mechanisms:Identification and Specification of Key Parts[J]. Computers & Industrial Engineering,2005,49(2):241-265.
[12]张斌.精密工程中免形状测量的关键技术研究[D].北京:北京工业大学,2012.