圆锥形凹模径向分块压边拉深工艺实验研究

摘要/Abstract

摘要：

采用圆锥形凹模拉深工艺可以提高成形极限，但需要用压边圈将板坯先压成与凹模面吻合的形状，当变形程度较大时，板坯很容易起皱。为了克服这一缺点，提出了将圆锥形凹模与径向分块压边方法结合的工艺，该工艺可有效改善压边圈与板坯的约束状态,从而达到抑制起皱的目的。对圆筒形件的拉深成形，采用了刚柔复合的径向分块压边圈结构，设计了圆锥形凹模径向分块多压边圈拉深模，取不同凹模半锥角的圆锥形凹模进行了圆筒形件的拉深成形实验。实验表明,新的压边方法能有效克服初始成形过程的起皱，可与锥度较小的凹模一起使用。采用凹模半锥角为45°的凹模,得到AA5754、AA6061和08Al三种板材的极限拉深系数分别为0.410、0.431、0.373，显著提高了成形极限。对圆锥形凹模的拉深成形，给出了理论计算成形极限的方法，理论与实验结果非常接近。

关键词: 圆锥形凹模拉深成形, 径向分块压边, 起皱, 拉深成形极限

Abstract:

The forming limit could be improved by using the conical die in the deep drawing process when the blank was drawn to the shape accordant to the inside surface of the die.And the blank wrinkled easily during the large deformation process.A new technology combining the conical die with the radial segmental blank holding technique was proposed to improve the restrain conditions between the blank holders and the blank and to suppress the wrinkles.The drawing die were designed with the conical die and the rigid-flexible composite segmental blank holders and the experiments for the cylindrical cup deep drawing process were conducted using the conical dies with different die semi-cone angles.The results reveal that the wrinkles at the beginning of the drawing process can be overcame effectively by the new blank holding method with smaller conical angles. The forming limit coefficients for AA5754, AA6061 and 08AL are as 0.410,0.431 and 0.373 respectively, which are enhanced effectively, adopting the die with 45° die semi-cone angle.The theoretical forming limit calculation method for the deep drawing process with the conical die is given and the theoretical results are accordant with the experimental ones.

Key words: deep drawing process with conical die, radial segmental blank holding, wrinkling, forming limit of deep drawing

中图分类号:

TG386.1

孔晓华, 秦泗吉, 陆宏, 郑星. 圆锥形凹模径向分块压边拉深工艺实验研究[J]. 中国机械工程, 2015, 26(18): 2528-2532,2538.

Kong Xiaohua, Qin Siji, Lu Hong, Zheng Xing. Experimental Research on Deep Drawing Process Using Radial Segmental Blank Holders with Conical Die[J]. China Mechanical Engineering, 2015, 26(18): 2528-2532,2538.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2015/V26/I18/2528

参考文献

[1]Kergen R,Jodogne P.Computerized Control of the Blank Holder Pressure on Deep Drawing Process[J].SAE Paper,1992,920433.
[2]Manabe K,Yang M,Yoshihara S,et al.Artificial Intelligence Identification of Process Parameters and Adaptive Control System for Deep-drawing Process[J].Materials Proeessing Technology,1998,80:421-426.
[3]Siegert K,Wagner S,Ziegler M,et al.Closed Loop Binder Force System[J].SAE Special Publications,1996,960824.
[4]Siegert K,Zeigler M,Wagner S,et al.Closed Loop Control of the Friction Force-deep Drawing Process[J].Journal of Materials Processing Technology,1997,71(1):126-133.
[5]Yagami T,Manabe K,Yamauchi Y,et al.Effect of Alternating Blank Holder Motion of Drawing and Wrinkle Elimination on Deep-drawability[J].Journal of Materials Processing Technology,2007,187:187-191.
[6]Hassan M A,Suenaga R,Takakura I V,et al.A Novel Process on Friction Aided Deep Drawing Using Tapered Blank Holder Divided into Four Segments[J].Journal of Materials Processing Technology,2005,159(3):418-425.
[7]赵磊,黄顶社,刘全坤.基于分块压边圈的汽车后柱加强板回弹控制[J].模具工业,2010,36(5):87-92.
Zhaolei,Huang Dingshe,Liu Quankong.Control of Springback in the Forming Process of Reinforcing Plate of Automotive Back Column Based on Segmented Blank Holder[J].Die & Mould Industry,2010,36(5):87-92.
[8]秦泗吉,黄晓忠,王婧.径向分块双压边圈轴对称拉深成形工艺研究[J].中国机械工程,2011,22(14):1741-1744.
Qin Siji,Huang Xiaozhong,Wang Jing.Research on Axisymmetrical Deep Drawing Process Based on Radial Double Segmental Blank-holder Technique[J].China Journal of Mechanical Engineering,2011,22(14):1741-1744.
[9]熊志清.圆杯无压边锥模拉深皱曲强度与拉深极限预测[J].机械工程学报,2001,37(9):75-78.
Xiong Zhiqing.Prediction on Wrinking Strength and Linming Drawing Ration for Cup Deep-drawing Without Blankolder through a Conical Die[J].Chinese Journal of Mechanical Engineering,2001,37(9):75-78.
[10]Hezam L M A,Hassan M A,Hassab-Allah I M,et al.Development of a New Process for Producing Deep Square Cups through Conical Dies[J].International Journal of Machine Tools and Manufacture,2009,49(10):773-780.
[11]刘琼,程培元,吴卫超.曲面凹模优化拉深工艺的模拟研究[J].冲压,2008(5):82-84.
Liu Qiong,Cheng Peiyuan,Wu Weichao.The Simulation Research on Drawing Technology of Curved Die[J]. Stamping, 2008(5):82-84.
[12]梁炳文,胡世光.板料成形塑性理论[M].北京:机械工业出版社,1987.
[13]秦泗吉.轴对称拉深成形凸缘变形区应力应变解析求解[J].机械工程学报,2011,47(24):20-25.
Qin Siji.Analytical Solution of Stress in Flange Deformation in Axisymmetrical Deep Drawing Process[J].Journal of Mechanical Engineering.2011,47(24):20-25.
[14]Yossifon S,Tirosh J.Rupture Instability in Hydroforming Deep-drawing Process[J].International Journal of Mechanical Sciences,1985,27(9):559-570.