基于最小二乘映射的多参数结构问题快速计算方法

中国机械工程 ›› 2011, Vol. 22 ›› Issue (6): 706-709.

基于最小二乘映射的多参数结构问题快速计算方法

陈沛;韩旭;姜潮;张正

湖南大学汽车车身先进设计制造国家重点实验室,长沙,410082

出版日期:2011-03-25 发布日期:2011-04-15
基金资助:
国家自然科学基金资助项目(10802028)
National Natural Science Foundation of China（No. 10802028）

Efficient Method for Computation of Multi-parameterized Problem Based on Least Square Mapping

Chen Pei;Han Xu;Jiang Chao;Zhang Zheng

State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,Hunan University,Changsha,410082

Online:2011-03-25 Published:2011-04-15
Supported by:
National Natural Science Foundation of China（No. 10802028）

摘要/Abstract

摘要：

针对机械工程中复杂结构多参数问题,提出一种新的基于最小二乘映射的减基法。该方法通过在参数域采集样本点，计算系统在有限个样本点下的响应以构造减基空间,利用最小二乘映射把原方程向减基空间进行投影得到减缩方程，在减基空间快速求解该减缩系统，获得原问题的减缩解，并把减缩解还原到原空间，得到问题的近似解。当系统参数发生变化时，能通过减缩系统快速得到新参数下的响应，极大地提高了计算效率。最后将该方法用于赛车车架刚度计算,结果表明方法是有效且可靠的。

关键词:

减基法, 最小二乘映射, 多参数问题, 拉丁超立方采样

Abstract:

A new reduced-basis method based on the least square mapping was suggested to improve the efficiency of solving complex and multi-parameterized problems in mechanical engineering.In this method,sampling points were obtained from the parameter domain,and a reduced-basis space was constructed by computing responses of the problem at these points.Then the least square mapping was employed to conduct projection from original space onto the reduced-basis space.A reduced system was obtained and

can be solved efficiently.By projecting the reduced solution back into the original space,an approximate solution of the original system was obtained efficiently and accurately.Even with new variables, the solution can be obtained fastly by solving the reduced system.The numerical example demonstrates that this method is of validity and reliability.

Key words:

reduced-basis method, least square mapping, multi-parameterized problem, Latin hypercube sampling

中图分类号:

TB121

陈沛, 韩旭, 姜潮, 张正.

基于最小二乘映射的多参数结构问题快速计算方法

[J]. 中国机械工程, 2011, 22(6): 706-709.

CHEN Pei, HAN Xu, JIANG Chao, ZHANG Zheng.

Efficient Method for Computation of Multi-parameterized Problem Based on Least Square Mapping

[J]. China Mechanical Engineering, 2011, 22(6): 706-709.

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.