覆盖件模具拼接区表面微观几何形貌的反演分析

doi:10.3969/j.issn.1004-132X.2021.07.007

摘要/Abstract

摘要： 为提高车身覆盖件模具拼接区的加工质量，首先分析不同加工参数下拼接缝前后的表面形貌几何特性和残留高度的空间特性，然后基于小波包提取加工表面轮廓信号不同频段的能量熵特征，最后根据能量熵特征、材料去除率和刀具寿命预测函数反演表面形貌的加工参数。研究结果表明，基于反演分析方法得到的加工参数可以实现拼接区微观几何形貌的可控。

关键词: 拼接模具, 表面形貌, 小波包, 能量熵, 反演分析

Abstract: In order to improve processing quality of splicing areas for body cover panel die, the geometric characteristics of surface appearance and spatial characteristics of residual height before and after splicing seams were analyzed separately under different processing parameters. And then, energy entropy of different frequency bands for contour signals of the processing surfaces was extracted based on wavelet packets characteristics. Finally, processing parameters of the surface topography were retrieved according to the energy entropy characteristics, material removal rate, and tool life prediction function. Research results show that the processing parameters obtained based on inversion analysis method may achieve controllable micro-geometry of the splicing areas.

Key words: splicing mould, surface topography, wavelet packet, energy entropy, inversion analysis

中图分类号:

TH164

吴石, 赵洪伟, 李鑫. 覆盖件模具拼接区表面微观几何形貌的反演分析[J]. 中国机械工程, 2021, 32(07): 806-804.

WU Shi, ZHAO Hongwei, LI Xin. Inversion Analysis of Surface Micro-geomorphology in Splicing Areas of Cover Molds[J]. China Mechanical Engineering, 2021, 32(07): 806-804.

参考文献

［1］吴石，杨琳，刘献礼，等. 覆盖件模具曲面曲率特征对球头刀铣削力的影响［J］. 机械工程学报， 2017, 53(13):188-198.
WU Shi, YANG Lin, LIU Xianli, et al. Influence of Curvature Characteristics of Sculptured on Milling Force in Ball-end Milling of Panel Moulds［J］. Journal of Mechanical Engineering， 2017, 53(13):188-198.
［2］LIU Xianli, GAO Haining, YUE Caixu, et al. Modeling of Cutting Force and Surface Quality in the Seam Area of Splicing Dies［J］. Journal of Vibration, Measurement and Diagnosis， 2018, 38(3):429-437.
［3］SENATORE J, SEGONDS S, RUBIO W, et al. Correlation between Machining Direction, Cutter Geometry and Step-over Distance in 3-axis Milling：Application to Milling by Zones［J］. Computer Aided Design, 2012, 44(12):1151-1160.
［4］OMAR O, WARDANY E, ELBESTAWI M A. An Improved Cutting Force and Surface Topography Prediction Model in End Milling［J］. International Journal of Machine Tools and Manufacturing, 2007, 47(7/8):1263-1275.
［5］GAO T, ZHANG W H, QIU K P, et al. Numerical Simulation of Machined Surface Topography and Roughness in Milling Process［J］. Journal of Manufacturing Science and Engineering, 2006, 128：96-103.
［6］LIU X, SOSHI M, SAHASRABUDHE A, et al. A Geometrical Simulation System of Ball End Finish Milling Process and Its Application for the Prediction of Surface Micro Features［J］. Journal of Manufacturing Science and Engineering, 2006, 128(1):74-85.
［7］PENG F Y, WU J, FANG Z L. Modeling and Controlling of Surface Micro-topography Feature in Micro-ball-end Milling［J］. International Journal of Advanced Manufacturing Technology, 2013(1):145-154.
［8］王鹏，王西彬，颜培，等. 切削刃数量对球墨铸铁铣削性能及表面形貌特征的影响［J］. 表面技术, 2018, 47(12):314-320.
WANG Peng, WANG Xibin， YAN Pei, et al. Effect of Number of Cutting Edges on Cutting Performance and Surface Morphology in Face Milling of Nodular Cast Iron［J］. Surface Technology, 2018, 47(12):314-320.
［9］任志英，高诚辉. 小波变换在粗糙表面几何形貌表征中的应用［J］. 中国工程机械学报, 2013, 11(1):78-82.
YIN Zhigao, GAO Chenghui. Applications of Wavelet Transform for Rough-surface Morphological Characterization［J］. Chinese Journal of Construction Machinery, 2013, 11(1):78-82.
［10］刘帅. 多轴球头铣削表面形貌分析及摩擦系数研究［D］. 济南：山东大学, 2015.
LIU Shuai. Morphological Analysis of Multi-axial Ball End Milled Surfaces and Research on FrictionCoefficient［D］. Jinan:Shandong University, 2015.
［11］WANG Q, LIU F, WANG X. Multi-objective Optimization of Machining Parameters Considering Energy Consumption［J］. The International Journal of Advanced Manufacturing Technology, 2014, 71(5/8):1133-1142.
［12］NATARAJAN E, KAVIARASAN V, LIM W H, et al. Enhanced Multi-objective Teaching-learning-based Optimization for Machining of Delrin［J］. IEEE Access, 2018, 6:51528-51546.
［13］陶会荣，张福民，曲兴华. 真实加工表面后向散射特性分析及表面参数反演［J］. 光谱学与光谱分析, 2015, 35(7):1986-1991.
TAO Huirong, ZHANG Fumin, QU Xinghua. Backscattering Characteristics of Machining Surfaces and Retrieval of Surface Multi-parameters［J］. Spectroscopy and Spectral Analysis, 2015, 35(7):1986-1991.
［14］陈建岭，孙杰，李剑峰. 钛合金铣削加工参数多目标优化研究［J］. 中国机械工程, 2014, 25(2):169-173.
ZHANG Jianling, SUN Jie, LI Jianfeng. Multi-objective Optimization of Cutting Parameters during Milling of Titanium Alloys［J］. China Mechanical Engineering, 2014, 25(2):169-173.
［15］张臣，周来水，余湛悦，等. 基于仿真数据的数控铣削加工多目标变参数优化［J］. 计算机辅助设计与图形学学报, 2005(5):1039-1045.
ZHANG Chen, ZHOU Laishui, YU Zhanyue, et al. Multi-objective and Varying Parameter Optimization of Machining Parameters Based on NC Simulation Data［J］. Journal of Computer-aided Design and Computer Graphics, 2005(5):1039-1045.

[1]	梁淑宝, 张培林, 曹建军, 任国全. 基于蚁群优化的提升小波包渐变式阈值降噪方法 [J]. J4, 201016, 21(16): 1964-1969.
[2]	范思敏;肖继明;董永亨;洪贤涛;赵亭. 球头铣刀铣削球面的表面形貌建模与仿真研究[J]. 中国机械工程, 2020, 31(24): 2924-2930，2936.
[3]	岳彩旭;刘鑫;刘智博;谢娜;王彦武. 基于有限元仿真的拼接模具铣削用刀具优化[J]. 中国机械工程, 2020, 31(17): 2085-2094.
[4]	张勇斌, 严广和, 李建原, 姜晨. 金刚石涂层微铣刀的铣削加工试验[J]. 中国机械工程, 2020, 31(15): 1772-1777.
[5]	刘伟1，2;商圆圆1，2;邓朝晖1，2;刘仁通1，2. 砂轮表面形貌定量评价及修整效果研究[J]. 中国机械工程, 2018, 29(19): 2277-2283.
[6]	麦云飞1;刘志亮1;王书文1;董冰洋2. 旋转滑动摩擦高频噪声产生机理的实验研究[J]. 中国机械工程, 2017, 28(18): 2198-2203,2208.
[7]	董彩云1;张超勇1;孟磊磊1;肖鹏飞1;罗敏2;林文文3. 基于谐波小波包和BSA优化LS-SVM的铣刀磨损状态识别研究[J]. 中国机械工程, 2017, 28(17): 2080-2089,2108.
[8]	张浩, 孙见君, 马晨波, 涂桥安. 机械密封端面形貌的三维重建及其表征[J]. 中国机械工程, 2017, 28(11): 1287-1291,1299.
[9]	胡中伟, 邵铭剑, 方从富, 于怡青, 徐西鹏, . 蓝宝石不同晶面轴向超声振动辅助磨削特性研究[J]. 中国机械工程, 2017, 28(11): 1380-1385.
[10]	张建宇, 孟浩, 胥永刚. 基于信源估计和频域反卷积的滚动轴承故障特征分离与辨识[J]. 中国机械工程, 2017, 28(01): 45-51.
[11]	张宇飞, 么子云, 唐松林, 朱丽娜, 张进杰. 一种基于主成分分析和支持向量机的发动机故障诊断方法[J]. 中国机械工程, 2016, 27(24): 3307-3311.
[12]	曾一凡, 杨卫平, 吴勇波, 刘曼利. 超声振动辅助固结磨粒抛光硅片表面形成机理及实验[J]. 中国机械工程, 2016, 27(23): 3208-3214.
[13]	张高峰, 何杨, 鲁炎鑫, 周后明, 朱科军. 碳纤维增强复合材料低温冷风磨削试验研究[J]. 中国机械工程, 2016, 27(20): 2779-2784,2790.
[14]	吴芬, 黄美发, 陈磊磊, 吴常林. 基于多分辨率奇异值分解的表面滤波方法[J]. 中国机械工程, 2016, 27(13): 1766-1772.
[15]	周友行, 杨文佳, 谢赛元, 张俏, 章本毅. 孔系钻削振动信号特征波动可视化研究及其应用[J]. 中国机械工程, 2016, 27(12): 1615-1620.