采用薄膜热电偶的多层印刷电路板原位钻削温度测量

中国机械工程

采用薄膜热电偶的多层印刷电路板原位钻削温度测量

崔云先1;牟瑜1;王成勇2;郑李娟2;殷俊伟1;薛生俊1

1.大连交通大学机械工程学院, 大连, 116028
2.广东工业大学机械工程学院, 广州, 510643

出版日期:2019-11-25 发布日期:2019-11-26
基金资助:
国家自然科学基金资助项目(51575074，51875110)

In-situ Drilling Temperature Measurement of Multilayer PCB Using Thin Film Thermocouple

CUI Yunxian1;MU Yu1;WANG Chengyong2;ZHENG Lijuan2;YIN Junwei1;XUE Shengjun1

1. School of Mechanical Engineering， Dalian Jiaotong University， Dalian, Liaoning,116028
2. School of Mechanical Engineering，Guangdong University of Technology， Guangzhou, 510643

Online:2019-11-25 Published:2019-11-26

摘要/Abstract

摘要： 针对工业用多层印刷电路板(PCB)加工过程中钻削温度难以准确测量的技术难题，提出了一种基于薄膜热电偶的PCB各板层原位钻削温度测量方法。根据PCB的截面结构采用材料叠层建模方法对PCB钻削过程进行建模仿真，掌握了钻削过程中PCB钻削温度的分布及变化情况，并确定了传感器最佳镀膜位置为钻头进给方向的垂直底部。采用直流脉冲磁控溅射技术，在不同层数的PCB上制备薄膜热电偶传感器，并对其静、动态性能进行研究，结果表明所研制的温度传感器在30~200 ℃范围内，塞贝克系数为37.4 μV/℃，非线性误差不超过0.65%，动态响应时间为0.095ms。对不同层数的PCB进行了多组钻削温度测量实验，结果显示，钻削过程中4层、12层、20层的最高钻削温度分别为49.30 ℃、53.90 ℃、63.90 ℃，且每组重复实验的温度相对稳定，温度测量误差不超过0.8 ℃。该测量方法为PCB高速钻削工艺改进提供了参考。

关键词: 印刷电路板, 薄膜热电偶, 原位钻削温度, 钻削仿真

Abstract: Aiming at the technical problems that it were difficult to measure drilling temperature accurately in the processes of the industrial PCB drilling, a method was proposed based on thin film thermocouple sensor to measure the in-situ drilling temperatures of each layer during PCB drilling processes. The drilling processes of PCB were modeled and simulated by method of layered material modeling according to cross-section structures of PCB. The distribution and variations of PCB drilling temperatures during the drilling processes were clarified. The sensor optimum coating positions were the vertical bottoms of the bit feed directions. Thin film thermocouple sensors were deposited on different PCB layers by DC pulsed magnetron sputtering. The static and dynamic performances of the sensors were studied. Results show that the Seebeck coefficient of the temperature sensor is as 37.4 μV/℃ in the range of 30~200 ℃. The non-linear error is less than 0.65%. The dynamic response time is as 0.095 ms.Several groups of drilling temperature measurements were carried out on different PCB layers. Results show that the maximum drilling temperatures of 4 layers, 12 layers and 20 layers during drilling processes are 49.30 ℃, 53.90 ℃ and 63.90 ℃ respectively. The temperature of each group of repeated experiments is stablize, and the errors are less than 0.8 ℃. In summary, the method provides a reference for improving PCB high speed drilling processes.

Key words: printed circuit board(PCB), thin film thermocouple, in-situ drilling temperature, drilling simulation

中图分类号:

TH811

崔云先1;牟瑜1;王成勇2;郑李娟2;殷俊伟1;薛生俊1. 采用薄膜热电偶的多层印刷电路板原位钻削温度测量[J]. 中国机械工程.

CUI Yunxian1;MU Yu1;WANG Chengyong2;ZHENG Lijuan2;YIN Junwei1;XUE Shengjun1. In-situ Drilling Temperature Measurement of Multilayer PCB Using Thin Film Thermocouple[J]. China Mechanical Engineering.

参考文献

[1]KUS A, ISIK Y, CAKIR M C, et al. Thermocouple and Infrared Sensor-based Measurement of Temperature Distribution in Metal Cutting[J]. Sensors, 2015,15(1):1274-1291.
[2]QIU F, HAN L. Temperature Measurement for Stacked Die Chip by Using Infrared Radiation Thermometer[C]∥International Conference on Electronic Measurement &Instruments. Chengdu, 2011:71-76.
[3]王成勇，廖冰淼.一种多层PCB钻孔钻削温度的测量装置及方法：中国，CN104568212A [P].2017-07-11.
WANG Chengyong, LIAO Bingmiao. A Multi-layer PCB Drilling Temperature Measuring Device and Method: China, CN104568212A [P]. 2017-07-11.
[4]周春雷.本构模型参数对切削过程仿真影响的研究[J]. 现代制造工程, 2017(1)：105-109.
ZHOU Chunlei. Study on the Influence of Constitutive Model Parameters on Cutting Process Simulation [J].Modern Manufacturing Engineering, 2017 (1)：105-109.
[5]王海涛.6061铝合金高速铣削有限元仿真与实验研究[D].青岛：青岛理工大学，2015.
WANG Haitao. Finite Element Simulation and Experimental Study on High Speed Milling of 6061 Aluminum Alloy[D].Qingdao: Qingdao University of Technology, 2015.
[6]PAVAN A, DAYANANDA P, VIJAYA K M, et al. Influence of Seawater Absorption on Vibrational and Tensile Characteristics of Quasi-isotropic Glass/Epoxy Composites[J]. The Journal of Materials Research and Technology,2018：1427-1433.
[7]SRIVASTAVAV K. Influence of Water Immersion on Mechanical Properties of Quasi-isotropic Glass Fibre Reinforced Epoxy Vinylester Resin Composites[J]. Materials Science & Engineering：A (Structural Materials:Properties, Microstructure and Processing), 1999, 263(1):56-63.
[8]MIYANO Y, NAKADA M , NISHIGAKI K . Prediction of Long-term Fatigue Life of Quasi-isotropic CFRP Laminates for Aircraft Use[J]. International Journal of Fatigue, 2006, 28(10):1217-1225.
[9]殷俊伟,贾振元,王福吉，等. 基于CFRP切削过程仿真的面下损伤形成分析[J]. 机械工程学报, 2016, 52(17):58-64.
YIN Junwei, JIA Zhenyuan, WANG Fuji, et al. Analysis of Under-surface Damage Formation Based on CFRP Cutting Process Simulation [J]. Journal of Mechanical Engineering, 2016, 52 (17): 58-64.
[10]崔云先.瞬态切削用NiCr/NiSi薄膜热电偶测温刀具研究[D].大连：大连理工大学，2011.
CUI Yunxian. Research on NiCr/NiSi Thin Film Thermocouple Temperature Measuring Tool for Transient Cutting[D]. Dalian: Dalian University of Technology, 2011.
[11]崔云先,胡晓勇,薛帅毅.高速动车组轴温测量用特种结构薄膜传感器的研制[J]. 中国机械工程, 2018, 29(1):63-69.
CUI Yunxian, HU Xiaoyong, XUE Shuaiyi. Development of Thin Film Sensor with Special Structure for Axle Temperature Measurement of High-speed EMU [J].China Mechanical Engineering, 2018, 29 (1): 63-69.
[12]崔云先,薛帅毅,周通.薄膜瞬态温度传感器的制备及性能研究[J]. 仪器仪表学报, 2017,38(12):3028-3035.
CUI Yunxian, XUE Shuaiyi, ZHOU Tong, et al. Fabrication and Performance of Thin Film Transient Temperature Sensors [J]. Chinese Journal of Scientific Instrument, 2017,38(12): 3028-3035.