结构参数对提升阀性能的影响

摘要/Abstract

摘要： 针对电站锅炉中蒸汽吹灰器低能耗、高效率的要求，基于浸入实体方法，研究了提升阀阀座入口收缩角α及出口扩大角β对提升阀开启过程动态特性的影响，获得了不同收缩角及不同扩大角所对应的流量特性曲线。结果表明：α由20°增大至50°时，阀门小开度下的出口流量增加了23%；β由0°增大至15°时，阀门大开度下出口流量增加了56%；结构允许范围内，增大收缩角可提高阀门小开度下的流量，增大扩大角可提高阀门大开度的流量。

关键词: 提升阀, 阀座, 数值模拟, 流量

Abstract: For the requirements that steam soot blowers of utility boiler should have high efficiency and low cost, based on immersed solid method, the influences of shrinkage angle α and expansion angle β on the opening dynamic characteristics were studied, and the flow curves of different shrinkage angles and different enlargement angles were obtained. The results show that flow rate increases 23% at the small opening when α increases from 20° to 50°, flow rate increases 56% at the large opening when β increases from 0° to 15°. Increasing shrinkage angle may improve the flow rate at the small opening, and increasing expansion angle may improve the flow rate at the large opening within the ranges of the structure.

Key words: poppet valve, valve seat, numerical simulation, flow rate

中图分类号:

TK175

范宜霖1;张继伟1;胡春艳1;李树勋2. 结构参数对提升阀性能的影响[J]. 中国机械工程.

FAN Yilin1;ZHANG Jiwei1;HU Chunyan1;LI Shuxun2. Influences of Structural Parameters on Properties of Poppet Valves#br#[J]. China Mechanical Engineering.

参考文献

[1]SREB M. Integrated Life Synthesis for Boiler Sootblowers in Fossil Power Plants[J]. Computers and Structures, 1997, 63(6): 1043-1051.
[2]朱予东,阎维平,欧宗现. 熵产分析法在锅炉吹灰优化模型中的应用[J].中国电机工程学报,2008,28(8):13-17.
ZHU Yudong, YAN Weiping, OU Zongxian. Application of Entropy Generation Analysis on Research of Sootblowing Optimization for Boiler[J]. Proceedings of the CSEE, 2008, 28(8):13-17.
[3]杨卫娟,周俊虎,刘建忠,等. 600MW机组锅炉吹灰器优化投用分析[J].热力发电, 2005(1):24-26.
YANG Weijuan, ZHOU Junhu, LIU Jianzhong, et al. Analysis of Sootblowing Optimization for Boiler for 600MW Unit[J]. Thermal Power Generation, 2005(1): 24-26.
[4]ANSYS Inc. Release 15.0 Documentation for ANSYS [G]. Canonsburg, PA, USA, ANSYS Inc., 2015.
[5]谢龙汉，赵新宇，张炯明.ANSYS CFX流体分析及仿真[M]. 北京：电子工业出版社, 2010．
XIE Longhan, ZHAO Xinyu, ZHANG Jiongming. ANSYS CFX Fluid Analysis and Simulation[M]. Beijing: Publishing House of Electronics Industry ,2010.
[6]郭昌盛，林腾蛟，吕和生，等.基于浸入固体法的湿式离合器调压阀流场数值仿真[J]. 机械研究与应用, 2013(3): 1-3.
GUO Changsheng, LIN Tengjiao, LYU Hesheng, et al. Numerical Simulation of Fluid in the Pressure Regulating Valve of Wet Clutch Based on Immersed Solids Method[J]. Mechanical Research & Application,2013(3):1-3.
[7]纪兵兵，陈金梅．ANSYS ICEM CFD网格划分技术实例详解[M]．北京：水利水电出版社，2012．
JI Bingbing, CHEN Jinmei. ANSYS ICEM CFD Meshing Technology Example[M]. Beijing: China Water & Power Press,2012.
[8]李树勋，王虎斌，范宜霖，等.氮气式水击泄压阀初启阶段动态特性研究[J]. 华中科技大学学报(自然科学版),2016,44(7):10-13.
LI Shuxun, WANG Hubin, FAN Yilin, et al. Study on Dynamic Characteristics of Nitrogen Surge Relief Valve and in Opening Process[J]. Journal of Huazhong University of Science and Technology (Natural Science), 2016,44(7):10-13.
[9]SONG X G, CUI L, PARK Y C. Three-dimensional CFD Analysis of Spring-loaded Pressure Safety Valve from Opening to Re-closure[C]//Proceedings of the ASME 2010 Pressure Vessels and Piping Division/K-PVP Conference. Washington DC: ASME, 2010:295-303.
[10]刘亚俊,唐电,魏华刚.清洗机斜盘轴向柱塞泵流道的流场仿真与结构优化设计[J]. 中国机械工程, 2013, 24(17): 2358-2361.
LIU Yajun, TANG Dian, WEI Huagang. Flow Field Simulation and Structure Optimal Design for Passage in Swash Plate Axial Piston Pump of Pressure Washer[J]. China Mechanical Engineering, 2013, 24(17): 2358-2361.
[11]李树勋，范宜霖，叶琛，等.基于改进设计的平衡阀开孔型线优化及试验[J]. 浙江大学学报(工学版), 2015,49(5):908-915.
LI Shuxun, FAN Yilin, YE Chen, et al. Optimization and Text for Opening Profile Line of Balance Valve Based on Improved Design[J]. Journal of Zhejiang University (Engineering Science) 2015,49(5):908-915.
[12]TAO G, CHEN H Y, J Y Y. Optimal Design of the Magnetic Field of a High-speed Response Solenoid Valve [J]. Journal of Materials Processing Technology, 2002, 129(1/3): 555-558.
[13]弓永军，周华，杨华勇.结构参数对先导式纯水溢流阀性能的影响[J]. 浙江大学学报(工学版),2006,40(5):869-873.
GONG Yongjun, ZHOU Hua, YANG Huayong. Properties of Pilot Operated Water Hydraulic Relief Valve with Different Structure Parameters[J]. Journal of Zhejiang University (Engineering Science) , 2006,40(5):869-873.

[1]	郭威, 孙洪鸣, 徐高飞, 李广伟, 周悦, 王敏健, . 全海深着陆车着底冲击特性与集中应力结构改进[J]. 中国机械工程, 2021, 32(07): 867-874.
[2]	杜飞;王新云;邓磊;夏巨谌;金俊松. 高速冲击连接技术的研究进展[J]. 中国机械工程, 2021, 32(05): 600-610.
[3]	乔巍1;姚卫星1,2. 剪滞效应对复合材料固化变形影响的数值分析[J]. 中国机械工程, 2021, 32(05): 611-616,623.
[4]	胡健1;陈泽中1;刘涛2;杨金华3. 车门防撞梁热成形工艺优化仿真与试验[J]. 中国机械工程, 2021, 32(01): 92-100.
[5]	花少震, 孟凡净, 刘华博, 丁海. [成形过程仿真优化与集成计算材料工程]注射成形熔体喷射的三维模拟及消除对策研究[J]. 中国机械工程, 2020, 31(22): 2715-2722.
[6]	胡冕;丁晓红. 热管滚珠丝杠热性能仿真和实验[J]. 中国机械工程, 2020, 31(20): 2445-2453.
[7]	王林1;潘骏1;贺青川1;丁炜2;顾利威2. 后倾式离心风机叶轮机器人焊接工艺优化[J]. 中国机械工程, 2020, 31(19): 2379-2387.
[8]	包道日娜；刘旭江；王小雪；王帅龙；刘嘉文. 小型水平轴可变偏心距风力机输出特性分析[J]. 中国机械工程, 2020, 31(18): 2196-2205.
[9]	童哲铭1；陈尧1；童水光1；余跃1；李进富2；郝国帅3. 基于NSGA-Ⅲ算法的低比转速离心泵多目标优化设计[J]. 中国机械工程, 2020, 31(18): 2239-2246.
[10]	沈建邦;肖俊华;梁希;徐耀玲. 负泊松比曲边内凹蜂窝结构的面内冲击动力学数值研究[J]. 中国机械工程, 2020, 31(16): 1998-2004.
[11]	李顺;刘桓龙;陈冠鹏. 不同液压能耦合模式下蓄电池轨道工程车的加速功率特性[J]. 中国机械工程, 2020, 31(12): 1452-1460.
[12]	侯勇俊;王斌. 凸轮和齿扇齿条复合驱动的新型往复泵仿真及分析[J]. 中国机械工程, 2020, 31(09): 1074-1079,1088.
[13]	姚静1,2,3;寇成浩1;尹钰鑫1;孔祥东1,2;孙瑞辉4;李昊5. 超高压大流量比例插装阀测试方法[J]. 中国机械工程, 2020, 31(06): 638-646.
[14]	邹伟生1;刘瑞仙1;刘少军2. 粗颗粒海底矿石浆体提升电泵研究[J]. 中国机械工程, 2019, 30(24): 2939-2944.
[15]	岳敏楠1;李春1,2;郝文星1;张俊伟1. 气动弹片对翼型气动及噪声特性的影响[J]. 中国机械工程, 2019, 30(12): 1409-1416.