随动导丝及喷水机构大锥度高速电火花线切割研究

摘要/Abstract

摘要：

高速往复走丝电火花线切割机床大锥度（≥±5°）切割时，受到诸多因素的影响，尤其是电极丝采用导轮定位产生的结构误差的影响，加上切割时工作液不能很好地包裹住电极丝并随着电极丝沿倾斜方向进入加工区域，使其加工精度和表面粗糙度比直体切割时差很多，对于锥度零件的多次切割特别是大锥度零件的多次切割则显得更加困难，其根本原因是没有能够保持电极丝空间位置及稳定性的随动导丝器和喷水机构。为此，设计了一种随着电极丝倾斜能随动导丝并跟踪喷液的六连杆大锥度随动导丝及喷水机构。通过试验，在相同加工参数条件下，新型随动机构与现有机构相比，圆锥加工误差从80μm减小到40μm，表面粗糙度Ra从4.059μm减小至3.495μm，多次切割后加工精度可以达到25μm（锥度±20°，工件厚40mm），表面粗糙度Ra达到1.670μm。

关键词: 高速电火花线切割, 大锥度, 随动机构, 多次切割

Abstract:

Because many factors especially the structure error influences caused by wire electrode using wheel positioning, and dielectric fluid cannot grip the wire electrode very well so that could not flow into the machining area with wire electrode along the direction of dip when big taper parts in cutting, the machining accuracy and surface roughness of the taper parts were worse than parts with stretched cutting. Multi cutting of taper parts especially big taper parts was much more difficult. The basic reason was that it had no follow-up guide and spray mechanism which could keep the wire electrode space position and stability. In view of the above mentioned problems, the paper presented the design of a six connecting rod big taper follow-up guide and spray mechanism that could guide wire along with wire electrode's inclination and realize tracking spray at the same time. On the basis of new mechanism, experimental results show that taper machining errors decrease from 80μm to 40μm. Surface roughness Ra decreases from 4.059μm to 3.495μm. After multi cutting, taper machining (taper ±20°, thickness 40mm) errors are decreased to 25μm. Surface roughness Ra is decreased to 1.670μm.

Key words: high speed wire-cut electric discharge machining(HSWEDM), large taper, servo guide mechanism, multi cutting

中图分类号:

TG661

李凌铃, 刘志东, 岳伟栋. 随动导丝及喷水机构大锥度高速电火花线切割研究[J]. 中国机械工程, 2015, 26(9): 1167-1172.

Li Lingling, Liu Zhidong, Yue Weidong. Study on HSWEDM Possessing Function of Guiding Wire and Following-up Spray during Large Taper Cutting[J]. China Mechanical Engineering, 2015, 26(9): 1167-1172.

参考文献

[1]刘志东，高长水. 电火花加工工艺及应用[M]. 北京: 国防工业出版社, 2011.
[2]高素芳，孙保锋，王刚，等. 大锥度高速走丝线切割机床四连杆机构及控制软件的开发[C]//第12届全国特种加工学术会议. 长沙, 2007:4.
[3]陆霖琰，刘志东，田宗军，等. 高速走丝电火花线切割工作液失效研究[J]. 中国机械工程, 2011, 22(15): 1793-1797.
Lu Linyan, Liu Zhidong, Tian Zongjun, et al. Research on Cooling Liquid Failure of WEDM-HS[J]. China Mechanical Engineering, 2011, 22(15): 1793-1797.
[4]步丰林，李明辉. 超大厚度电火花线切割工艺研究[J]. 上海交通大学学报, 1996, 30(9): 124-128.
Bu Fenglin, Li Minghui.Technology Research of High Thickness HSWEDM Cutting[J]. Journal of Shanghai Jiaotong University, 1996, 30(9): 124-128.
[5]刘志东. 高速走丝电火花线切割工作液的性能要求及研究方向[J]. 航空精密制造技术, 2005, 41(3): 38-39.
Liu Zhidong. Research on the General Feature of Emulations and Dielectrics and Its Iendency in WEDM-HS[J]. Aviation Precision Manufacturing, 2005, 41(3): 38-39.
[6]张伟，陈文义. 流体力学[M]. 天津：天津大学出版社, 2009.
[7]范圣耀，张秋菊，陈海卫. 电火花线切割电极丝动态特性研究[J]. 机械科学与技术, 2012, 31(5): 771-777.
Fan Shengyao, Zhang Qiuju, Chen Weihai. Reviewing Dynamic Characteristics of Electrode Wire of Wire-cut Electrical Discharge Machining[J]. Mechanical Science and Technology, 2012, 31(5): 771-777.
[8]刘志东，潘阳，李谢峰，等. 往复走丝电火花线切割机床工艺特点及现状[J]. 电加工与模具, 2012(6): 60-64.
Liu Zhidong, Pan Yang, Li Xiefeng, et al. Process Characteristics and Status of High Speed Wire-cut Electrical Discharge Machine [J]. Electromachining & Mould, 2012(6): 60-64.
[9]刘志东，王振兴，张艳，等. 高速走丝电火花线切割高效切割技术研究[J]. 中国机械工程, 2011, 22(4): 385-389.
Liu Zhidong, Wang Zhenxing, Zhang Yan, et al.Efficient Cutting of High Speed Wire-Cut Electrical Discharge Machining by Liquid Spray[J]. China Mechanical Engineering, 2011, 22(4): 385-389.
[10]郭钟宁，李大超，俞大民，等. 电火花线切割加工中线电极的动态特性仿真与实验研究[J]. 中国机械工程, 2000,11(7): 32-36.
Guo Zhongning, Li Dachao, Yu Daming, et al.Dynamic Characteristics of the Simulation and Experimental Research of Wire Electrode in WEDM-HS[J]. China Mechanical Engineering, 2000,11(7): 32-36.
[11]刘志东，俞容亨. 高速走丝电火花线切割机床多次切割的实现[J]. 中国机械工程, 2007, 18(20): 2410-2413.
Liu Zhidong, Yu Ronghen.Realization of Multi-cutting in WEDM-HS[J]. China Mechanical Engineering, 2007, 18(20): 2410-2413.
[12]张艳. 高速走丝电火花多次切割精度及表面质量研究[D]. 南京：南京航空航天大学, 2010.