随焊冲击旋转挤压控制LD10薄板件焊接变形和热裂纹的研究

中国机械工程 ›› 2013, Vol. 24 ›› Issue (13): 1817-1821.

随焊冲击旋转挤压控制LD10薄板件焊接变形和热裂纹的研究

张勇;綦秀玲

辽宁工程技术大学，阜新，123000

出版日期:2013-07-10 发布日期:2013-07-11
基金资助:
先进焊接与连接国家重点实验室开放课题研究基金资助项目(AWPT-M12-01)

Control of Welding Residual Deformation and Hot Crack of LD10 Thin Plate by Welding with Impacting Rotation Compression

Zhang Yong;Qi Xiuling

Liaoning Technical University,Fuxin,Liaoning,123000

Online:2013-07-10 Published:2013-07-11

摘要/Abstract

摘要：

LD10铝合金薄板在焊接过程中易产生焊接热裂纹，焊后薄板件易产生较大的焊接变形。采用冲击旋转挤压头对焊缝及相邻区域施加一定频率的冲击旋转挤压作用,使焊缝及近缝区产生塑性延展;对LD10常规焊接件和随焊冲击旋转挤压件的焊接残余变形与焊接残余应力进行测量，对比分析了常规焊接件和随焊冲击旋转挤压件的拉伸试验、维氏硬度、断口分析和金相组织，明确了随焊冲击旋转挤压工艺对焊接件组织及性能的影响。试验结果表明，随焊冲击旋转挤压处理后，工件的残余应力被降低到较低水平，随焊冲击旋转挤压工艺起到控制焊接残余应力和变形的作用,并且抑制了焊接热裂纹的产生。

关键词: LD10, 焊接残余应力与变形, 热裂纹, 随焊冲击旋转挤压

Abstract:

Large welding residual deformation and hot cracks can be easily found during LD10 thin plate welding. The motion, welding with impacting rotation compression, was utilized to generate a force. The force acted on the weld bead and near weld zone to produce plastic extension. In order to know the effects of the welding with impact rotation compression on the microstructure and mechanical properties of the weldment, welding residual stress and deformation, metallographic observation, SEM of fracture, tensile experiment and hardness measurement of the weld joint were utilized. The experimental results show that the residual stress and deformation, hot crack can be reduced by the technology of welding with impacting rotation compression.

Key words: LD10, welding residual stress and deformation, hot cracking, welding with impacting rotation compression

中图分类号:

TG404

张勇, 綦秀玲. 随焊冲击旋转挤压控制LD10薄板件焊接变形和热裂纹的研究[J]. 中国机械工程, 2013, 24(13): 1817-1821.

ZHANG Yong, QI Xiu-Ling. Control of Welding Residual Deformation and Hot Crack of LD10 Thin Plate by Welding with Impacting Rotation Compression[J]. China Mechanical Engineering, 2013, 24(13): 1817-1821.

参考文献

[1]宋仁国. 高强度铝合金的研究现状及发展趋势[J]. 材料导报, 2001,14(1):20-21.
Song Renguo. Current Status and Trends in High Strength Aluminum Alloy Research[J].Materials Review, 2001,14(1):20-21.
[2]陈小会，揭小平，闫洪,等. 高强铝合金的研究现状及进展[J]. 材料导报,2009,23(14):489-492.
Chen Xiaohui, Jie Xiaoping, Yan Hong, et al. Research Status and Evolvements in High Strength Aluminum Alloy[J]. Materials Review, 2009,23(14):489-492.
[3]刘会杰.焊接冶金及其焊接性[M].北京:机械工业出版社，2007.
[4]Xu Wenli,Tian Xitang,Liu Xuesong,et al.A New Method for Welding Aluminum Alloy LY12CZ Sheet with High Strength[J].China Welding, 2001,10(2):121-127.
[5]刘伟平,田锡唐,张修智.一种防止高强铝合金焊接热裂纹产生的新方法[J].焊接学报,1995,16(2):106-111.
Liu Weiping,Tian Xitang,Zhang Xiuzhi. A New Method for Prevention of Weld Hot Cracking[J]. Transactions of the China Welding Institution, 1995,16(2):106-111.
[6]Kondakov T F. High Temperature Rolling in Welding Butt Joints[J]. Welding International,1988,2(2)：172-175
[7]邹增大，王新洪，曲仕尧. 锤击消除焊接接头残余应力的数值模拟[J]. 中国机械工程，1999，10(4):466-468.
Zou Zengda, Wang Xinhong, Qu Shiyao. The Numerical Simulation of the Peening Effect on Welding Residual Stress[J].China Mechanical Engineering, 1999，10(4):466-468.
[8]Terai K. Study on the Prevention of Welding Deformation in Thin-skin Plate Structures[J]. Kawasaki Technical Review, 1978, 61：61-66.
[9]Hanus F, Hubo R. Flame Straightening of Thermomechanically Rolled Structural Steel[J]. Steel Research, 1999,40(4/5)：193-197.
[10]范成磊，方洪渊，杨建国，等.随焊冲击碾压控制焊接应力变形新方法[J].机械工程学报，2004，40(8)：87-90.
Fan Chenglei,Fang Hongyuan, Yang Jianguo, et al. New Technology to Control Welding Stress and Distortion with Trailing Impacting Rolling[J]. Chinese Journal of Mechanical Engineering, 2004，40(8)：87-90.
[11]范成磊，方洪渊，陶军，等. 随焊冲击碾压控制焊接应力变形防止热裂纹机理[J]. 清华大学学报(自然科学版)， 2005,45(2):159-162.
Fan Chenglei, Fang Hongyuan, Tao Jun, et al. Mechanism of Weld with Trailing Impact Rolling to Control Residual Stresses Deformation and Hot Cracking[J]. Journal of Tsinghua University(Science and Technology), 2005,45(2):159-162.