中厚板辊式矫直过程模型算法修正与应用

中国机械工程 ›› 2012, Vol. 23 ›› Issue (3): 335-338.

中厚板辊式矫直过程模型算法修正与应用

王效岗;黄庆学;胡鹰

太原科技大学,太原,030024

出版日期:2012-02-10 发布日期:2012-02-15
基金资助:
国家重点基础研究发展计划(973计划)资助项目（2011CB612204）；国家青年自然科学基金资助项目（51105264）；山西省基础研究计划资助项目（2011021019-4）
National Program on Key Basic Research Project (973 Program)（No. 2011CB612204）;
National Natural Science Foundation of China（No. 51105264）

Correction and Application of Numerical Model on Plate Roller Levelling

Wang Xiaogang;Huang Qingxue;Hu Ying

Taiyuan University of Science and Technology,Taiyuan, 030024

Online:2012-02-10 Published:2012-02-15
Supported by:

National Program on Key Basic Research Project (973 Program)（No. 2011CB612204）;
National Natural Science Foundation of China（No. 51105264）

摘要/Abstract

摘要：

用数值计算和实验验证相结合的方法,研究了将材料模型和中性层偏移引入矫直模型的分层算法。研究结果表明：分层算法结果与实验数据有较好的一致性;运用分层算法通过变形运算,可得到每个弯曲单元的应力应变分布,同时得到截面上残余应力分布,在1~4弯曲单元,残余应力的最大值位于弹性区向塑性区的过渡处,在5~9弯曲单元,残余应力的最大值位于板材的表面。

关键词:

板材, 矫直模型, 中性层, 残余应力

Abstract:

A model of plate in level was studied herein using both numerical analysis and experimental verification.The results show that the relative accurate results can be obtained between measurement data and calculated results. It is obtained that the distribution of stresses and strains in the level init. The distribution of residual stress on the cross section is drawn at the same time, the results show that the maximum valve of residual stress locates at the transition part which transmit from elastic zone to plastic zone in 1~4 level unit, and locates at the plate surface in 5~9 level unit.

Key words: plate steel, leveling model, neutral layer, residual stress

中图分类号:

TG333.2

王效岗, 黄庆学, 胡鹰.

中厚板辊式矫直过程模型算法修正与应用

[J]. 中国机械工程, 2012, 23(3): 335-338.

WANG Xiao-Gang, HUANG Qiang-Hua, HU Ying.

Correction and Application of Numerical Model on Plate Roller Levelling

[J]. China Mechanical Engineering, 2012, 23(3): 335-338.

[1]	陈兴怖1，2;胡勇1，2;黄朝炎1，2;王尧3;王健3. 复杂曲度船体外板展开算法研究[J]. 中国机械工程, 2020, 31(08): 931-936.
[2]	张子骞1, 杨会林1, 田永利2. 薄壁管材矫直过程应变中性层偏移模型与分析[J]. 中国机械工程, 2013, 24(10): 1390-1395.
[3]	杨春强1, 2, 黄云1, 2, 吴建强1, 2. 船用螺旋桨砂带磨削表面质量的试验研究 [J]. 中国机械工程, 2011, 22(14): 1659-1663.
[4]	王效岗;黄庆学;马勤;. 中厚板的横向波浪矫直研究[J]. J4, 2009, 20(01): 0-23,4.