LED多线切割机同步控制系统研制

中国机械工程 ›› 2012, Vol. 23 ›› Issue (2): 131-134.

LED多线切割机同步控制系统研制

彭思齐1,2;戴瑜兴1;蒋近1

1.湖南大学,长沙,410082

2.湘潭大学,湘潭,411105

出版日期:2012-01-25 发布日期:2012-02-14
基金资助:
国家重大科技专项(2009ZX02011-02);国家发改委科研项目(20091168);湖南省重点科技计划资助项目(2009CK2005);湖南省教育厅资助科研项目(10C1282)
National Science and Technology Major Project ( No. 2009ZX02011-02);

Hunan Provincial Science and Technology Key program ( No. 2009CK2005);
Hunan Provincial Scientific Research Project of Ministry of Education of China（No. 10C1282）

Development of Synchronous Control System in LED Multi-wire Saw

Peng Siqi1,2;Dai Yuxing1;Jiang Jin1

1.Hunan University,Changsha,410082

2.Xiangtan University,Xiangtan,Hunan,411105

Online:2012-01-25 Published:2012-02-14
Supported by:

National Science and Technology Major Project ( No. 2009ZX02011-02);

Hunan Provincial Science and Technology Key program ( No. 2009CK2005);
Hunan Provincial Scientific Research Project of Ministry of Education of China（No. 10C1282）

摘要/Abstract

摘要：

同步控制是LED多线切割机控制系统成功的关键。分析了传统多线切割机切片过程的受力模型,针对其缺陷设计了一种加工罗拉摇摆装置,并给出其模糊迭代同步控制策略。与单一模糊控制方法相比,该策略充分考虑了机器改进后的结构特点和运行过程中的多种干扰,使用PD模糊控制器使系统迅速达到稳定状态并具有一定精度后,再利用迭代学习控制器消除PD模糊控制器的稳态误差。实验对比证明,该算法具有控制精度高、切片质量好的特点。

关键词:

LED, 多线切割机, 摆动装置, 模糊迭代控制, 同步控制

Abstract:

A synchronous control is the crucial to success on LED multi-wire saw control system.The stress model of traditional multi-wire saw slicing process was analyzed.Aiming at the limitation of the current system,a rocking processing roller equipment was proposed,and a fuzzy iteration control policy was given in the synchronous control of LED multi-wire saw.Comparing with the sole fuzzy control,this strategy has considered fully the structural feature of the improved multi-wire saw and many kinds of disturbances

during the operation processes.The PD fuzzy controller enables the system to achieve the steady state rapidly,and the system has certain precision.After achieving steady state,the iterative study controller can eliminate the PD fuzzy controller’s static error.The experimental contrast proves that this algorithm has high control precision and good quality of slice. 

Key words: LED, multi-wire saw, rocking equipment, fuzzy iteration control, synchronization control

中图分类号:

TP273DOI

彭思齐1, 2, 戴瑜兴1, 蒋近1.

LED多线切割机同步控制系统研制

[J]. 中国机械工程, 2012, 23(2): 131-134.

BANG Sai-Ji-1, 2, DAI Yu-Xin-1, JIANG Jin-1.

Development of Synchronous Control System in LED Multi-wire Saw

[J]. China Mechanical Engineering, 2012, 23(2): 131-134.

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.