双层缩套厚壁筒自增强残余应力分析

中国机械工程 ›› 2012, Vol. 23 ›› Issue (11): 1364-1368.

双层缩套厚壁筒自增强残余应力分析

袁格侠1;刘宏昭2;赵迎祥1;魏宏波1

1.宝鸡文理学院,宝鸡,721016
2.西安理工大学,西安,710048

出版日期:2012-06-10 发布日期:2012-06-14
基金资助:
陕西省教育厅专项科研计划项目(2010JK397)；宝鸡市2010年科技计划工业攻关项目；宝鸡文理学院重点科研项目(ZK11066)
Shanxi Provincial Specialized Science Research Program of Ministry of Education of China（No. 2010JK397）

#br# Analysis of Autofrettaged Residual Stress of Shrink-fit Two-layer Thick-wall Cylinders

Yuan Gexia1;Liu Hongzhao2;Zhao Yingxiang1;Wei Hongbo1

1.Baoji University of Arts and Sciences, Baoji, Shaanxi,721016
2.Xi'an University of Technology, Xi'an, 710048

Online:2012-06-10 Published:2012-06-14
Supported by:

Shanxi Provincial Specialized Science Research Program of Ministry of Education of China（No. 2010JK397）

摘要/Abstract

摘要：

基于ANSYS平台,使用APDL语言开发了双层缩套厚壁筒自增强残余应力求解参数化有限元接触模型。考虑缩套预应力的影响,基于理想弹塑性材料模型和Mises屈服准则,推导出了双层缩套厚壁筒自增强残余应力解析解,并将其有限元分析值和解析解进行了比较,有限元分析值与解析解在屈服区结果一致,而在弹性区略有差别,与已有的解析解相比,由于考虑了缩套初始预应力对自增强处理过程应力状态的影响,其残余应力有限元模型的仿真结果和解析解都具有更高的精度。


关键词: 双层厚壁筒, 缩套, 自增强, 接触分析, 残余应力

Abstract:

Based on ANSYS platform, APDL language of ANSYS was used to model parametric contact of two-layer thick-wall cylinders. Consideration of shrinkage residual stress, analytical solutions of autofrettaged residual stress of shrink-fit two-layer thick-wall cylinders was firstly given based on ideal elastic-plastic material mechanics model and Mises yield criterion. Comparison of the finite element analysis data with analytical solutions shows they are the same in yield zone, but are a little different in the elastic zone. Comparing with existing analytical solutions, the finite element model simulation results and analytical solution of the residual stress of the two-layer cylinders herein have higher precision for considering the effects of shrinkage stress on autofrettaged processing. 

Key words: two-layer thick-wall cylinder, shrink-fit, autofrettage, contact analysis, residual stress

中图分类号:

TH49

袁格侠1, 刘宏昭2, 赵迎祥1, 魏宏波1. 双层缩套厚壁筒自增强残余应力分析[J]. 中国机械工程, 2012, 23(11): 1364-1368.

YUAN Ge-Xia-1, LIU Hong-Zhao-2, DIAO Ying-Xiang-1, WEI Hong-Bei-1. #br# Analysis of Autofrettaged Residual Stress of Shrink-fit Two-layer Thick-wall Cylinders[J]. China Mechanical Engineering, 2012, 23(11): 1364-1368.

参考文献

[1]Yuan Gexia, Liu Hongzhao,Wang Zhongmin. Opti- mum Design for Shrink-fit Multi-layer Vessels under Ultrahigh Pressure Using Different Materials [J]. Chinese Journal of Mechanical Engineering, 2010,23(5) :582-589.
[2]Jahed H, Farshi B, Karimi M. Optimum Autofret- tage and Shrink- fit Combination in Multi- layer Cylinders[J]. ASME J. Pressure Vessel Technolo- gy, 2006,128(5) :196-200.
[3]Majzoobi G H, Farrahi G H, Pipelzadeh M K, et al. Experimental and Finite Element Prediction of Bursting Pressure in Compound Cylinders [J]. International Journal of Pressure Vessels and Pip- ing,2004, 81: 889-896.
[4]Hanlon P C (EDT). Compressor Handbook [ M]. New York : McGraw- hill Professional Pub, 2001.
[5]邵国华,魏兆灿等编.超高压容器[M],2002:237.
[6]傅卫国[1],吴光华[2].热套圆筒最佳过盈量和自增强压力简捷计算[J].化工装备技术,1993,14(4):22-25.
[7]李敬安.水炮的多层自增强高压腔筒的优化设计方法.中国矿业学院学报,1986,.
[8]Parker A P. Bauschinger Effect Design Procedures for Compound Tubes Containing an Autofrettaged Layer[J]. ASME J. Pressure Vessel Technology, 2001,123(2):203-206.
[9]才鸿年等著.火炮身管自紧技术[M],1997:407.
[10]Parker A P, Kendall D P. Residual Stresses and Lifetimes of Tubes Subjected to Shrink Fit prior to Autofrettage[J]. ASME J. Pressure Vessel Tech- nology, 2003,125 (3) : 282-286.
[11]Lee Eunyup,Lee Youngshin, Yang Quiming,et al. Autofrettage Process Analysis of a Compound Cylinder Based on the Elastic- perfectly Plastic and Strain Hardening Stress-strain Curve[J]. Journal of Mechanical Science and Technology, 2009,23: 3153-3160.
[12]袁格侠[1,2],刘宏昭[1],范彩霞[1,3],王娟平[2],王胜[1].自增强超高压容器残余应力分析[J].中国机械工程,2011,22(5):536-540.

[1]	张波;魏冰阳;刘大可. 基于等切共轭的弧齿锥齿轮差曲面建立与解析[J]. 中国机械工程, 2020, 31(04): 459-464.
[2]	聂少武1,2;蒋闯2;邓效忠2;苏建新2;杨建军1;王建华3. Ease-off拓扑修正的准双曲面齿轮齿面修形方法[J]. 中国机械工程, 2019, 30(22): 2709-2715,2740.
[3]	曹雪叶, 赵均海 , 张常光. 基于三剪统一强度准则的厚壁圆筒自增强分析[J]. 中国机械工程, 2017, 28(01): 75-81.
[4]	周镇宇, 唐进元, 丁撼. 变位非正交面齿轮副小轮齿向修形轮齿接触分析[J]. 中国机械工程, 2016, 27(15): 2003-2009.
[5]	曹乃亮, 杨利伟, 李志来. 包带式解锁支座的设计与试验[J]. 中国机械工程, 2015, 26(18): 2447-2451.
[6]	陈海辉, 曾莹莹, 钟汉通. 残余应力松弛和自增强处理压力对在役高压容器的安全影响[J]. 中国机械工程, 2014, 25(23): 3227-3231.
[7]	刘伟先;周光明;王新峰;钱元 . 真空辅助湿法斜接型挖补修理后层合板拉伸性能研究[J]. 中国机械工程, 2014, 25(17): 2396-2401.
[8]	牟世刚, 冯显英, 李蕾. 滚珠型弧面凸轮连续传动机构承载接触分析 [J]. 中国机械工程, 2012, 23(4): 379-382.
[9]	钱凌云, 刘全坤, 王成勇, 李亨, 韩豫. 厚壁圆筒自增强压力的优化分析 [J]. 中国机械工程, 2012, 23(4): 474-479.
[10]	王效岗, 黄庆学, 胡鹰. 中厚板辊式矫直过程模型算法修正与应用 [J]. 中国机械工程, 2012, 23(3): 335-338.
[11]	袁格侠, 刘宏昭, 范彩霞, 王娟平, 王胜. 自增强超高压容器残余应力分析 [J]. 中国机械工程, 2011, 22(5): 536-540.
[12]	杨春强1, 2, 黄云1, 2, 吴建强1, 2. 船用螺旋桨砂带磨削表面质量的试验研究 [J]. 中国机械工程, 2011, 22(14): 1659-1663.
[13]	唐进元, 雷国伟. CNC机床运动误差对弧齿锥齿轮齿面接触质量的影响研究 [J]. 中国机械工程, 2010, 21(20): 2395-2401,2429.
[14]	李宝福, 刘平芳, 樊俊伟. 圆柱扭转弹簧扭矩计算方法的改进 [J]. 中国机械工程, 2010, 21(19): 2318-2321.
[15]	朱瑞林, 朱国林. 外压自增强圆筒的设计计算方法 [J]. 中国机械工程, 2010, 21(15): 1869-1874.