钛合金拉伸试棒粉末温压成形研究

中国机械工程 ›› 2010, Vol. 21 ›› Issue (22): 2751-2754.

钛合金拉伸试棒粉末温压成形研究

彭小明;庞俊忠;陈虹;吴伏家

中北大学,太原,030051

出版日期:2010-11-25 发布日期:2010-12-01
基金资助:
太原市科技项目基金资助项目(08121023)
Science and Technology Foundation of Taiyuan ( No. 08121023)

Study on Powder Warm Pressing for Titanium Alloy Tensile Test Bar

Peng Xiaoming;Pang Junzhong;Chen Hong;Wu Fujia

North University of China,Taiyuan，030051

Online:2010-11-25 Published:2010-12-01
Supported by:
Science and Technology Foundation of Taiyuan ( No. 08121023)

摘要/Abstract

摘要：

研究了钛合金拉伸试棒粉末温压成形过程。在双向压制方式下，采用一种新型聚合物作模壁润滑剂，并在用其作内润滑剂主要成分的情况下使经过特殊配制的钛合金粉末温压达到拉伸试棒的要求。实验结果表明：在700MPa压力和模具粗糙度Ra值不大于0.4μm的情况下，长径比超过6的钛合金试棒在110℃时压坯密度达到最高值4.0g/cm3，温度高于或低于110℃时，密度均减小。

关键词:

钛合金, 拉伸试棒, 温压, 致密化过程

Abstract:

The process of powder warm pressing for titanium alloy tensile test bar was studied.Under the conditions of two-way pressing,using a new polymer as die wall lubricant and the main ingredient of internal lubricant, the experiments made the titanium alloy powder formulated specially achieve the requirements of tensile test bar by warm pressing. The results show that: at 700MPa and

the Ra value of mold roughness is less than 0.4μm, the green density of titanium alloy test bar whose diameter-high ratio is more than 6 achieves the maximum of 4.0g/cm3 at the optimum of 110℃,above or below the temperature the density will be lower.

Key words: titanium alloy, tensile test bar, warm pressing, densification process

中图分类号:

TG146.23

彭小明, 庞俊忠, 陈虹, 吴伏家.

钛合金拉伸试棒粉末温压成形研究

[J]. 中国机械工程, 2010, 21(22): 2751-2754.

BANG Xiao-Meng, LONG Dun-Zhong, CHEN Gong, TUN Fu-Jia.

Study on Powder Warm Pressing for Titanium Alloy Tensile Test Bar

[J]. China Mechanical Engineering, 2010, 21(22): 2751-2754.

[1]	王合旭, 蒋彦龙, 施红, 韩建军. 飞机空气导管泄漏特性的试验研究及数值模拟[J]. 中国机械工程, 2015, 26(9): 1183-1188.
[2]	尹延国, 俞建卫, 王永国, 解挺, 田明, 宋平. 温压模具感应加热温度场的有限元模拟分析 [J]. 中国机械工程, 2011, 22(5): 611-615.
[3]	章凯, 李萍, 薛克敏. 高压扭转对铜粉锥形件温压成形的改善 [J]. 中国机械工程, 2011, 22(15): 1875-1879.
[4]	李登万, 陈洪涛, 许明恒, 钟成明. 基于均匀设计法的钛合金清洁加工试验研究 [J]. 中国机械工程, 2011, 22(1): 15-18.
[5]	危卫华, 徐九华, 傅玉灿, 侯红亮, 李志强. 改善钛合金切削加工性的置氢工艺及置氢量优化 [J]. 中国机械工程, 2010, 21(02): 196-201.
[6]	程继贵;蔡艳波;宋鹏;万磊;. W-Cu粉末温压成形的研究[J]. J4, 2009, 20(17): 0-2131.