液压支架双级安全阀设计及其快速动载冲击试验研究

doi:10.3969/j.issn.1004-132X.2023.18.006

中国机械工程 ›› 2023, Vol. 34 ›› Issue (18): 2194-2203.DOI: 10.3969/j.issn.1004-132X.2023.18.006

液压支架双级安全阀设计及其快速动载冲击试验研究

周国强1;王慧1,2;宋宇宁3;赵国超1,2

1.辽宁工程技术大学机械工程学院，阜新，123000
2.辽宁省大型工矿装备重点实验室，阜新，123000
3.营口理工学院机械与动力工程系，营口，115000

出版日期:2023-09-25 发布日期:2023-10-19
通讯作者: 王慧（通信作者），男，1960年生，教授、博士研究生导师。研究方向为机电液一体化系统仿真与应用及流体传动与控制。E-mail:wanghui9955@163.com。
作者简介:周国强，男，1996年生，博士研究生。研究方向为液压与气动元件设计及特性。E-mail:zgq7618@163.com。
基金资助:
国家自然科学基金（52204169）；辽宁省自然科学基金（2022-YKLH-07）；辽宁省教育厅科学研究经费（L2020011）;矿山液压技术与装备国家地方联合工程研究中心开放研究基金(MHTE23-R12)

Design of Double-stage Safety Valves for Hydraulic Support and Experimental Study of Their Rapid Dynamic Load Impact Test

ZHOU Guoqiang1;WANG Hui1,2;SONG Yuning3;ZHAO Guochao1,2

1.School of Mechanical Engineering,Liaoning Technical University,Fuxin,Liaoning，123000
2.Liaoning Provincial Key Laboratory of Large-scale Industrial and Mining Equipment,Fuxin,Liaoning，123000
3.Department of Mechanical and Power Engineering,Yingkou Institute of Technology,Yingkou,Liaoning，115000

Online:2023-09-25 Published:2023-10-19

摘要/Abstract

摘要： 为提高液压支架的抗冲击性和稳定性，设计了一种额定流量、额定压力分别为50 L/min和45 MPa的一级直动阀与额定流量、额定压力分别为1000 L/min、50 MPa的二级差动阀相组合的新型双级安全阀。开发了基于蓄能器组的快速动载冲击试验系统，利用AMESim-Simulink联合仿真技术获得了快速动载冲击试验系统的压力动态响应特性和双级安全阀压力流量动态响应特性，研制了快速动载冲击试验台样机对双级安全阀进行了测试。结果表明，二级差动阀额定压力、额定流量分别约为49.2 MPa和992 L/min，开启时间小于3 ms，压力稳定时间在13～15 ms范围内，卸荷时间小于5 ms，验证了设计的双级安全阀具有卸荷速度快与抗冲击性能优良的特点及快速动载冲击试验方案的正确性。

关键词: 液压支架, 双级安全阀, AMESim-Simulink联合仿真技术, 快速动载冲击试验

Abstract: In order to improve the impact resistance and stability of the hydraulic supports, a new type of double-stage safety valve combined with a first-stage direct-acting valve with rated flow and pressure of 50 L/min and 45 MPa respectively and a second-stage differential valve with rated flow and pressure of 1000 L/min and 50 MPa respectively was designed. Moreover, a rapid dynamic load impact test system was developed based on the accumulator group, and the pressure dynamic response characteristics of the rapid dynamic load impact test system and the pressure-flow dynamic response characteristics of the double-stage safety valve were obtained by using AMESim and Simulink combined-simulation technology. Finally, a rapid dynamic load impact test bench prototype was established to test the double-stage safety valves. The results show that the rated pressure and flow rate of the second-stage differential valve are about 49.2 MPa and 992 L/min respectively, the opening time is less than 3 ms, the pressure stabilization time is within 1315 ms, and the unloading time is less than 5 ms. The experiments verify that the designed double-stage safety valve has the characteristics of fast unloading speed and excellent impact resistance and the correctness of the rapid dynamic load impact test scheme.

Key words: hydraulic support, double-stage safety valve, AMESim and Simulink combined-simulation technology, rapid dynamic load impact test

中图分类号:

TD355

周国强, 王慧, 宋宇宁, 赵国超, . 液压支架双级安全阀设计及其快速动载冲击试验研究[J]. 中国机械工程, 2023, 34(18): 2194-2203.

ZHOU Guoqiang, WANG Hui, SONG Yuning, ZHAO Guochao, . Design of Double-stage Safety Valves for Hydraulic Support and Experimental Study of Their Rapid Dynamic Load Impact Test[J]. China Mechanical Engineering, 2023, 34(18): 2194-2203.

参考文献

［1］ZHAO T, LIU C, YETILMEZSOY K, et al. Segmental Adjustment of Hydraulic Support Setting Load in Hard and Thick Coal Wall Weakening:a Study of Numerical Simulation and Field Measurement［J］. Journal of Geophysics and Engineering, 2018, 15(6):2481-2491.
［2］王世博,张辉.综采工作面推移动力学模型与仿真分析［J］.机械工程学报,2022,58(7):117-130.
WANG Shibo, ZHANG Hui. Dynamic Model and Simulation Analysis of Advancement of Fully Mechanized Mining Face［J］. Journal of Mechanical Engineering, 2022,58(7):117-130.
［3］刘前进,徐刚,卢振龙,等.液压支架工况综合评价与预警模型研究及应用［J］.煤炭科学技术,2022,50(10):198-206.
LIU Qianjin, XU Gang, LU Zhenlong, et al. Research and Application of Comprehensive Evaluation and Early Warning Model of Hydraulic Support Working Condition Based on Working Resistance Analysis［J］. Coal Science and Technology, 2022, 50(10):198-206.
［4］张金虎,王国法,杨正凯,等.高韧性较薄直接顶特厚煤层四柱综放支架适应性和优化研究［J］.采矿与安全工程学报,2018,35(6):1164-1169.
ZHANG Jinhu, WANG Guofa, YANG Zhengkai, et al. Adaptability Analysisand Optimization Study of Four-leg Shield Caving Support in Ultra Thick Seam with High Toughness and Thinner Immediate Roof［J］. Journal of Mining & Safety Engineering, 2018,35(6):1164-1169.
［5］NIU Y C. Development of High Pressure and Constant Low Flow Test System for Hydraulic Support Safety Valve［C］∥IOP Conference Series:Earth and Environmental Science, 4th International Conference on Environmental, Industrial and Energy Engineering.Guiyang:IOP Publishing, 2020, 610(1):012014.
［6］WANG F T, DUAN C H, TU S H, et al. Hydraulic Support Crushed Mechanism for the Shallow Seam Mining Face under the Roadway Pillars of Room Mining Goaf［J］. International Journal of Mining Science and Technology, 2017, 27(5):853-860.
［7］PYTLIK A. Process Characteristics of Hydraulic Legs Equipped with Safety Valves at Dynamic Load Caused by a Mining Tremor［J］. Archives of Mining Sciences, 2015, 60(2):595-612.
［8］原长锁,张兴辉.8.8 m超大采高液压支架支护强度计算分析与应用［J］.煤炭科学技术,2019,47(增刊2):21-26.
YUAN Changsuo, ZHANG Xinghui. Calculation Analysis and Application of Suppurt Strength of 8.8 m Ultra Large Mining Height Hydraulic Supports［J］. Coal Science and Technology, 2019, 47(S2):21-26.
［9］丁飞,王谦.液压支架结构疲劳动态可靠性评估方法［J］.中国安全科学学报,2015,25(6):86-90.
DING Fei, WANG Qian. Fatigue Dynamic Reliability Assessment Method of Hydraulic Support Structure［J］. China Safety Science Journal, 2015, 25(6):86-90.
［10］王洁,张建卓,刘凌威.高压大流量快开阀仿真及实验研究［J］.中国机械工程,2018,29(8):916-922.
WANG Jie, ZHANG Jianzhuo, LIU Lingwei. Simulation and Experimental Study of High Pressure and Large Flow Quick Opening Valves［J］. China Mechanical Engineering, 2018, 29(8):916-922.
［11］赵怀志,王晓东.液压支架大流量安全阀冲击特性影响因素仿真分析［J］.液压与气动,2022,46(2):131-137.
ZHAO Huaizhi, WANG Xiaodong. Simulation Analysis of Influencing Factors on Impact Characteristics of Large Flow Safety Valve for Hydraulic Support［J］. Chinese Hydraulics & Pneumatics, 2022, 46(2):131-137.
［12］BARBARYAN T, HOSEINZADEH S, HEYNS P S, et al. Developing a Low-fluid Pressure Safety Valve Design through a Numerical Analysis Approach［J］. International Journal of Numerical Methods for Heat & Fluid Flow, 2019, 30(3):1427-1440.
［13］钟麒,谢耿,汪谢乐,等.多电压复合驱动的高速开关阀性能研究［J］.机械工程学报,2021,57(4):191-201.
ZHONG Qi, XIE Geng, WANG Xiele, et al. Performance Analysis of High Speed On/Off Valve by Multi-voltages Compound Excitation［J］. Journal of Mechanical Engineering, 2021, 57(4):191-201.
［14］ZONG C, LI Q, ZHENG F, et al. Fluid-structure Coupling Analysis of a Pressure Vessel-pipe-safety Valve System with Experimental and Numerical Methods［J］. International Journal of Pressure Vessels and Piping, 2022, 199(10):147-158.
［15］张嘉鹭,赵继云.液压支架大流量安全阀冲击特性试验系统设计与分析［J］.液压与气动,2021,45(11):62-68.
ZHANG Jialu, ZHAO Jiyun. Design and Analysis on Impact Characteristic Test System of Hydraulic Support Large Flow Safety［J］. Chinese Hydraulics & Pneumatics, 2021, 45(11):62-68.
［16］穆洪远,程硕,李凯,等.线性高速开关阀的设计及验证［J］.机械工程学报,2021,57(22):247-254.
MU Hongyuan, CHENG Shuo, LI Kai, et al. Design and Verification of Linear High-speed On-off Valve［J］. Journal of Mechanical Engineering, 2021, 57(22):247-254.
［17］姚静,寇成浩,尹钰鑫,等.超高压大流量比例插装阀测试方法［J］.中国机械工程,2020,31(6):638-646.
YAO Jing, KOU Chenghao, YIN Yuxin, et al. Test Methods of Uitra-high Pressure and Large Flow Proportional Cartridge Valves［J］. China Mechanical Engineering, 2020, 31(6):638-646.
［18］张晋,朱汉银,姚静,等.某双阀芯电液比例多路阀主阀进口节流流场及阀口压降特性研究［J］.中国机械工程, 2017,28(10):1135-1143.
ZHANG Jin, ZHU Hanyin, YAO Jing, et al. Research on Flow Field and Pressure Drop Characteristics of Main Valve Inlet Throttle of a Dual Spool Electro-hydraulic Proportional Multi-way Valve［J］. China Mechanical Engineering, 2017, 28(10):1135-1143.
［19］张建卓,王洁,潘一山,等.6500 kN静-动复合加载液压冲击试验机研究［J］.煤炭学报,2020,45(5):1648-1658.
ZHANG Jianzhuo, WANG Jie, PAN Yishan, et al. Hydraulic Impact Test Bench with 6500 kN Static and Dynamic Composite Loading［J］. Journal of China Coal Society, 2020, 45(5):1648-1658.
［20］畅军亮.高压大流量安全阀设计及实验系统研究［D］. 徐州：中国矿业大学,2015.
CHANG Junliang. Research on the High Pressure and Large Flow Relief Valve Design and Experimental System［D］. Xuzhou:China University of Mining and Technology, 2015.
［21］COLOMBO D, LIMA G B A, PEREIRA D R, et al. Regression-based Finite Element Machines for Reliability Modeling of Downhole Safety Valves［J］. Reliability Engineering & System Safety, 2020, 198(6):106-118.
［22］刘磊.高压大冲击流量条件下乳化液锥阀失效机理及关键技术研究［D］.徐州：中国矿业大学,2016.
LIU Lei. Failure Mechanism and Key Technology of Emulsion Poppet Valve under Condition of High-pressure Large-impact-flow［D］. Xuzhou:China University of Mining and Technology, 2016.
［23］宋宇宁.液压支架用抗冲击双级保护大流量安全阀研究［D］.阜新：辽宁工程技术大学,2017.
SONG Yuning. Research on a High Capacity Unloading Valve with the Characteristics of Impact Resistance and Double-stage Protection for Hydraulic Support［D］. Fuxin:Liaoning Technical University, 2017.
［24］CHAO Z Q, NING C M, LI H Y. A Study of Simulation of Hydropreumatic Suspension Experiment Rig Based on Amesim and MATLAB/Simulink［J］. Applied Mechanics and Materials, 2014, 599(8):207-211.
［25］王慧,周国强,宋宇宁,等.液压支架抗冲击双级安全阀参数耦合特性研究［J］.中国安全科学学报,2021, 31(10):23-31.
WANG Hui, ZHOU Guoqiang, SONG yuning, et al. Study on the Dynamic Characteristics of the Anti-impact Two-stage High-flow Safety Valve Parameter Coupling of Hydraulic Support［J］. China Safety Science Journal, 2021, 31(10):23-31.

液压支架双级安全阀设计及其快速动载冲击试验研究

Design of Double-stage Safety Valves for Hydraulic Support and Experimental Study of Their Rapid Dynamic Load Impact Test

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 1

编辑推荐

Metrics