矩形管辊弯成形角部充满度分析及试验验证

doi:10.3969/j.issn.1004-132X.2023.07.013

中国机械工程 ›› 2023, Vol. 34 ›› Issue (07): 866-874.DOI: 10.3969/j.issn.1004-132X.2023.07.013

矩形管辊弯成形角部充满度分析及试验验证

邢梦龙1;杜凤山1;付玉涛2

1.燕山大学国家冷轧板带装备及工艺工程技术研究中心，秦皇岛，066004
2.秦皇岛宸铭异型管制造有限公司，秦皇岛，066000

出版日期:2023-04-10 发布日期:2023-05-04
通讯作者: 杜凤山（通信作者），男，1960年生，教授、博士研究生导师。研究方向为轧钢设备、工艺及数字化技术。E-mail:fsdu@ysu.edu.cn。
作者简介:邢梦龙，男，1992年生，博士研究生。研究方向为孔型设计及辊弯成形工艺。E-mail:xingmenglong1016@163.com。
基金资助:
国家自然科学基金（51975510）；河北省自然科学基金（E2017203043）

Analysis and Experimental Verification of Corner Filling Degree of Rectangular Tube Roll Forming

XING Menglong1;DU Fengshan1;FU Yutao2

1.National Cold Rolling Strip Equipment and Process Engineering Technology Research Center of
Yanshan University,Qinhuangdao,Hebei,066004
2.Qinhuangdao Chen-Ming Special-shaped Pipe Manufacturing Co.,Ltd.，Qinhuangdao,Hebei,066000

Online:2023-04-10 Published:2023-05-04

摘要/Abstract

摘要： 为了提高矩形管辊弯成形角部的成形精度，根据体积不变定律和金属秒流量相等原则对矩形管角部欠充满原因进行分析；结合工厂实际生产参数建立辊弯成形有限元模型，分析圆管管径和壁厚对成形过程中增厚系数、角部充满度的影响；根据角部欠充满区域中性层弧长线性对应关系进行圆管管径修正，确定系数修正关系式；对角部成形过程进行损伤判定，筛选出合适的圆管管径，将其仿真结果与试验进行对比。结果表明：辊弯成形过程中壁厚的增大使得角部处于欠充满状态；壁厚越小，成形过程中的增厚系数越小，所需圆管管径越小；圆管管径越大，角部充满度越好，同时管径的增大会增加辊弯出口处角部内侧损伤的可能性；仿真与试验结果的误差较小，验证了仿真模型的准确性。

关键词: 辊弯成形, 角部充满度, 系数修正, 角部损伤

Abstract: In order to improve the forming accuracy of square rectangular tube corners formed by roller forming, the causes of underfilling rectangular tube corners were analyzed according to the law of constant volume and the principle of equal metal flow per second. The finite element model of roll forming was established according to the actual production parameters in the factories, and the influences of pipe diameter and wall thickness on the thickening coefficient and corner filling degree in the forming processes were analyzed. According to the linear relation of arc length of neutral layer in underfilled regions of the corner, the tube diameter was corrected and the coefficient correction relation was determined. The damage of the corner forming processes was judged, and the appropriate diameter of the round pipe was selected. The simulation results were compared with the experimental ones. The results show that the corners are underfilled with the increase of wall thickness during roll forming. The decrease of wall thickness leads to the decrease of thickening coefficient, and the required diameters of circular pipes are smaller. With the increase of pipe diameters, the corner filling degree is better, at the same time, the increase of pipe diameters will increase the possibility of damage in the inner corner at the exit of roll forming. The errors between the test results and the experimental results are small, which verifies the accuracy of the simulation model.

Key words: roll forming, corner filling degree, coefficient modification, corner damage

中图分类号:

TG306

邢梦龙, 杜凤山, 付玉涛. 矩形管辊弯成形角部充满度分析及试验验证[J]. 中国机械工程, 2023, 34(07): 866-874.

XING Menglong, DU Fengshan, FU Yutao. Analysis and Experimental Verification of Corner Filling Degree of Rectangular Tube Roll Forming[J]. China Mechanical Engineering, 2023, 34(07): 866-874.

参考文献

［1］HALMOS G T. Roll Forming Handbook［M］. Boca Raton：CRC Press，2006:2-5.
［2］NAGAMACHI T, NAKAKO T, NAKAMURA D. Effects of Forming Conditions of Roll Offset Method on Sectional Shape at the Corner of Square Steel Pipe［J］. Materials Transactions, 2013, 54:1703-1708.
［3］NAGAMACHI T, NAKAKO T, NAKAMURA D. Mechanism of Pipe End Deformation after Cutting of Square Steel Pipe Formed by Roll Forming［J］. Materials Transactions, 2013, 54:1910-1915.
［4］ABRINI K, FARAHMAND H R. An Upper Bound Analysis for the Reshaping of Thick Tubes with Experimental Verification［J］. International Journal of Mechanical Sciences, 2008,50:342-358.
［5］FARAHMAND H R, ABRINI K. An Upper Bound Analysis for Reshaping Thick Tubes to Polygonal Cross-section Tubes through Multistage Roll Forming Process［J］. International Journal of Mechanical Sciences, 2015,100:90-98.
［6］BAYOUMI L S. Cold Drawing of Regular Polygonal Tubular Sections from Round Tubes［J］. International Journal of Mechanical Sciences, 2001,43:2541-2553.
［7］BAYOUMI L S. Analysis of Flow and Stresses in Flattening a Circular Tube by Rolling［J］. Journal of Materials Processing Technology, 2002, 128:130-135.
［8］LEU D K, WU J Y. Finite Element Simulation of the Squaring of Circular Tube［J］. International Journal of Advanced Manufacturing Technology, 2005, 25:691-699.
［9］HOSSEINZADEH M, MOUZIRAJI M G. An Analysis of Tube Drawing Process Used to Produce Squared Sections from Round Tubes through FE Simulation and Response Surface Methodology［J］.International Journal of Advanced Manufacturing Technology, 2016,87:2179-2194.
［10］YAO Y, QUACH W M, YOUNG B. Finite Element-based Method for Residual Stresses in Cold-formed Steel Hollow Sections［J］. Engineering Structures, 2019, 188:24-42.
［11］YAO Y, QUACH W M, YOUNG B. Cross-section Behavior of Cold-formed Steel Elliptical Hollow Sections—a Numerical Study［J］. Engineering Structures, 2019,201:109797.
［12］YAO Y, QUACH W M, YOUNG B. Simplified Models for Residual Stresses and Equivalent Plastic Strains in Cold-formed Steel Elliptical Hollow Sections［J］. Thin-Walled Structures,2020,154:106835.
［13］彭雪锋，陈强，王宇，等.局部感应加热对高强钢方管二次辊压成形的影响［J］.工程科学学报，2016,38(7):973-978.
PENG Xuefeng, CHEN Qiang, WANG Yu, et al. Effect of Local Induction Heating on Secondary Roll-forming of High Strength Square Tubes［J］. Chinese Journal of Engineering, 2016,38(7):973-978.
［14］韩飞，张涛.中厚壁方管冷弯成形效应研究［J］. 焊管，2016,39(7):61-64.
HAN Fei, ZHANG Tao. Experimental Investigation on Cold-forming Effect of Middle Thick-walled Square Tube［J］. Welded Pipe and Pipe, 2016,39(7):61-64.
［15］曾国，郭永进，于忠奇，等.辊弯成形方形型钢的残余应力［J］. 钢铁研究学报，2008,20(11):29-32.
ZENG Guo, GUO Yongjin, YU Zhongqi, et al. Residual Stresses of Roll-formed Shape with Square Section［J］. Journal of Iron and Steel Research, 2008,20(11):29-32.
［16］徐树成，刘才.方矩形管第一道次辊弯成形过程的变形和应力场［J］. 燕山大学学报，2000,24(1):15-18.
XU Shucheng, LIU Cai. The Deformation and Stress Field for Square Rectangle Tube Roll Forming Process in First Pass［J］. Journal of Yanshan University, 2000,24(1):15-18.
［17］徐树成，刘才.方矩形管连续辊弯成形过程的变形和应力场［J］. 机械工程学报，2000,36(3):93-96.
XU Shucheng, LIU Cai. Deformation and Stress Field of Square Rectangle Tube in Continue Roll Forming Process［J］. Chinese Journal of Mechanical Engineering, 2000,36(3):93-96.
［18］杜凤山，陆卫平，张建宇，等.方管闭式辊弯成形过程的变形及流场［J］. 东北重型机械学院学报，1997，21(2):100-103.
DU Fengshan，LU Weiping，ZHANG Jianyu， et al. Deformation and Flow Fields of the Square Tube Forming of 4-roll Bending［J］. Journal of Northeast Heavy Machinery Institute, 1997,21(2):100-103.
［19］杜凤山，付志强，于辉.矩形管冷弯成形的辊花设计及成形规律［J］. 中国机械工程，2016,27(21):2841-2845.
DU Fengshan，FU Zhiqiang，YU Hui．Roll Flower Design and Forming Mechanism of Rectangular Pipes in Cold Roll Forming Processes［J］. China Mechanical Engineering, 2016,27(21):2841-2845.
［20］付志强，安子军，杜凤山，等.方矩形管连续辊弯成形延伸规律［J］. 吉林大学学报(工学版)，2015, 45(2):487-493.
FU Zhiqiang, AN Zijun, DU Fengshan, et al. Elongation of Rectangular Tube in Continuous Roll Forming［J］. Journal of Jilin University (Engineering and Technology Edition), 2015, 45(2):487-493.
［21］曹国富，卢启威.方矩管管壁增厚的原因分析［J］. 焊管，2010，33(7):55-59.
CAO Guofu, LU Qiwei. Discussion on Thickening Reason of Rectangular Pipe Wall Thickness［J］. Welded Pipe and Tube, 2010,33(7):55-59.
［22］杜凤山，邢梦龙，裴新元，等.一种考虑增厚系数的圆管成型方矩形管孔型设计方法：CN， 202110057360.5［P］. 2022-03-15.
DU Fengshan，XING Menglong，PEI Xinyuan，et al. Circular Tube Forming Square Rectangular Tube Pass Design Method Based on Thickening Coefficient:CN，202110057360.5［P］. 2022-03-15.
［23］MA H, XU W C,JIN B C, et al. Damage Evaluation in Tube Spinnability Test with Ductile Fracture Criteria［J］. International Journal of Mechanical Sciences, 2015,100:99-111.
［24］BAO Y B, WIERZBICKI T. On the Cut-off Value of Negative Triaxiality for Fracture［J］. Engineering Fracture Mechanics, 2005, 72:1049-1069.

矩形管辊弯成形角部充满度分析及试验验证

Analysis and Experimental Verification of Corner Filling Degree of Rectangular Tube Roll Forming

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics